similar to: Exporting a PCI Device

Dear, I''m looking to get Xen running on a system that (afterwards) seems a bit too new. The board has the Intel G33 chipset with the Intel ICH9 southbridge. This chipset is NOT supported by kernel 2.6.18 which ships with Xen 3.1.2 (and Debian Etch). So the question is: * What version of Xen to install to get going? Should I choose unstable? * What distribution will be the easiest to get

Hi - Is there someone around who successfully got cLVM on Debian/Lenny working? I was wondering if I was the only one facing problems with... Thanks in anticipation, -- Olivier Le Cam Département des Technologies de l''Information et de la Communication CRDP de l''académie de Versailles _______________________________________________ Xen-users mailing list

Hi, I''m on a HP DL365, amd64, running SLES10sp1, but with kernel and xen of SLES10sp2, therefore using Xen 3.2. The domU shall be a Windows HVM guest. I want use the Qlogic SAN card in a domU. I''m following these instructions: http://www.novell.com/communities/node/2880/assign-dedicated-network-card-or-pci-device-xen-virtual-machine well, there is written that this only

Hi everyone, Just a quick question: Is there a limit on the vbd size for pv guest domains, I''ve found only rumors on the Internet about a 2TB limit, but from my experience with xen-3.0.3 /linux-kernel-2.6.18-5 (installed from a debian etch packages) I can say that a lvm volume of 3.7TB as created and formated in Dom0 is seen as 1.85TB only of course reporting a corrupted xfs filesystem

Hi, I have been testing XenServer 4.1 and I have migrated to Xen 3.2.1 due to the lack of PCI passthrough in Citrix XenServer. I''ve spent 6 hours this evening installing backports packages and/or compiling the source in a fresh Debian Etch install. But still my DomU is crashing. I suspect I have too many versions floating around now so I will try again from scratch. What is the simplest

Hi, I use Xen 3.0.3-1 on a Debian Etch with LVM to store my DomUs. I already exploit a Windows 2000 in a DomU but I can''t install a windows NT4 Server: I have a death of Blue Screen during the installation begining. Did someone test that scary NT4 DomU with success? I think NT4 need a disk driver but wich one? and how can I give it one? My last solution to test is: to convert a NT4

Hello. I''m trying to set up hvm for linux or windows. I start with a very simple configuration without disks at all. but the virtual machine does boot or even "power up". If i remove the ioemu from the network device and specify type=brige or type=route everything goes fine, the boot process is starting but then I cant get network working in the guest.

Hi List, is it possible with the virt-manager to choose a drbd device? Example: 9:testsever Connected Primary/Secondary UpToDate/UpToDate C is running on /dev/sda9 but I can´t use it as a drive. (syntax?) Best, Mike _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users

Dear, I''ve attempted to upgrade a Xen box from 3.1.2 to 3.2.1. Unfortunately it has been a partial success only. At this point I''m really stuck with a network problem that affects my HVM machines (Linux PV run fine). The really odd thing is that everything seems to work properly, except that the "vif" network interfaces in dom0 seem to have only dropped TX packets for

Hey guys, Has anyone had much success with XCP and Open Stack together? I''m in the process of putting together a open stack test cluster and I thought I might be able to use XCP dom0''s for it.. but to be honest it doesn''t look so good. I tried following these instructions on a separate XCP test machine: http://wiki.openstack.org/XenServerDevelopment At a first test

Hi All, I want to test REMUS over XEN, I would like to know the basic steps to be followed . I have installed xen4.1 on debian and i didn''t find any command related to remus, is there any steps which i have to carry out? _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users

What is the simplest OS I can install in Xen, preferably Linux based, and don''t tell me MS-DOS :). I have installed a minimal version of Fedora, but I want something that is even less cluttered. I have looked at Minix, but it is not fully supported. I need something small, lightweight (doesn''t have to be multi-threaded or anything), that will run small C and Assembler programs

Hi all, did somebody successfuly export ISDN Cards to DomU? I want to have 2 ISDN Cards in DomU (for Asterisk with mISDN) lspci -vt -[0000:00]-+-00.0 nVidia Corporation MCP55 Memory Controller +-01.0 nVidia Corporation MCP55 LPC Bridge ... +-05.1 nVidia Corporation MCP55 SATA Controller +-06.0-[0000:01]--+-00.0 Cologne Chip Designs GmbH ISDN

I''m needing to put a network card on a test server XCP 1.0. I''m seeing the citrix hcl (http://hcl.xensource.com) and I''m a doubt. I base that on which version to look for a compatible card? If the kernel is the same as in 5.6.0 FP1, but if the version of XCP uses the hypervisor 3.4.2 neither appears on the list. ps: I had a RTL-8169 but stopped working with update 0.5

Hello Everyone, I am new with XCP. I''ve setup several hosts with* XCP 1.0* and manage it through XenCenter and command console. Each host has two NICs, one (xenbr0) connected to a physical switch for Internet (said sw1), the other (xenbr3) connected to a physical switch for internal network (said sw2). I am trying to setup VMs and VLANs on xenbr3. I created a virtual bridge by

Hai, I am using dell insprion 580 machine for xen installation and dom0 configuation. I compiled xen source code and configured the kernal. Grub entry given below menuentry ''Xen 4.0.0-rc8 / Ubuntu 10.4 kernel 2.6.32.25 pvops'' { insmod ext2 set root=''(hd0,3)'' multiboot (hd0,3)/boot/xen-4.0.0-rc8.gz module (hd0,3)/boot/vmlinuz-2.6.32.25 dummy=dummy

Hai, I am using dell insprion 580 machine for xen installation and dom0 configuation. I compiled xen source code and configured the kernal. Grub entry given below menuentry ''Xen 4.0.0-rc8 / Ubuntu 10.4 kernel 2.6.32.25 pvops'' { insmod ext2 set root=''(hd0,3)'' multiboot (hd0,3)/boot/xen-4.0.0-rc8.gz module (hd0,3)/boot/vmlinuz-2.6.32.25 dummy=dummy

Does Xen Cloud Platform (XCP) support the notion of a driver domain? I can assign a VIF to a domain, but it seems that I can only attach that VIF to a network. What I''d like to do is attach the front-end VIF in one domain to a backend running in another domain. The second domain will control the physical interface (via PCI passthrough). This use case is easily supported using Xen +

On Wed, May 25, 2011 at 12:41 AM, JAMES BOND 123 007 <james123007@gmail.com> wrote: > Hi , > I saw your thread post at > http://web.archiveorange.com/archive/v/ZvO4jnaavtTfcyqnHoRX > , about problems with XEN 4.0 installation. > I have the same problem and my machine is similar to yours( HP Proliant > DL380G6, 4GB-RAM) This question is better asked on the xen-users list.

I have installed Ubuntu Intrepid Server on bare metal and successfully ran:- # apt-get install ubuntu-xen-server.     It installed several packages on system . Now i can see files /boot/xen-3.3.gz, /etc/init.d/xend, /etc/init.d/xendomains, but no xenified kernel gets in. Attempt  to use vmlinuz-2.6.27-7-server, obviously , fails with system panic.    I do remember recompiling  procedure for Xen