similar to: airlink gigabit ethernet card

Hi guys; I'm having a problem with a new pc that has an Realtec ethernet device. Don't know why the driver is not loading and is not detected during installation process. I tried to load r8169.ko unsuccessfully. It load but no device is detected. No dmesg or /var/log/message. ?Any help on how I can configure correctly this ethernet device? This are the data that I have: # lspci

Hi, I set up a ring group. I would like for people who select a certain voice menu option to ring a list of extensions (I have just one extension in there at the moment) and if it doesn't answer to go to an extension's voice mail. I am using a version of asterisk from CVS, last updated a couple of weeks ago. This line in extensions_addtional.conf sends the call to ringgroup 3 if

Hi! I?m having trubbles with the speed on my samba server, I just uppgraded to gigabit (Realtek 8169 NIC) at home when i copy stuff from the samba server i get around 5-6Mb/sec and if i use ftp to access the same file on the same server i get almost 30Mb/sec does anyone have a clue what causes this problem? When i used my old 3com 905c for the local net i got normal 100Mbit speed (around

Hi all, I swapped a Realtek 8139 100M Net Card for a Realtek 8169 Gig Net card in a Centos 5.6 system. After reconfiguring the network settings I find that on boot up the 8169 interface does not start. The startup script says something like "The 8169 is not available..." ifconfig -a shows a device with the right mac address called __tmpsomethingorother I can get it going if I

I need to get a second ethernet card for my HP Proliant CentOS server, to attach a LinkSys WRT54GL router to. I see that there are many Realtek RTL8169S gigabit cards going for a song on eBay. Is anyone using one of these under CentOS? Do they work OK? (I used to have a couple of Realtek cards - not gigabit - and they worked fine.) Or does anyone have a strong recommendation for other cards? Any

Ok, not exactly an Asterisk problem, but... I picked up some SNOM 200 phones because SNOM's have been recommended for use with Asterisk and they have line buttons that can subscribe to presence. However, they don't appear to power up when connected to my Negear FS108P, which is an 802.3af Power-over-ethernet capable hub. I am pretty sure these are the SNOM 200b, in that the ethernet

Hello, Marvel Yukon Gigabit Ethernet is supported by CentOS ? -- -- Devel in Precio http://www.pas-world.com

Hello all, I want to learn about requirements if I want to protect gigabit network with ipfilter as transparent firewall. Which type of hardware is required to install FreeBSD + ipf (as transparancy ) . We use 3 gigabit ethernet to protection which type of gigabit ethernet carts are powerfull. Also, what about the NMBCLUSTERS , IPSTATE_SIZE and IPSTATE_MAX in ip_state.h. I want to collect all

Hi all, I am notice strange behaviour of samba in our mixed fastEthernet/gigabitEthernet enviroment. First of all let me to describe our situation. We have a samba server running debian unstable with 2.6.3 kernel installed. Server has a gigabit copper connection (tg3 driver) to the 100/1000 Megabit switch (3COM 4228G). Client is a WinXP/Linux workstation connected by ordinary 100 Megabit

Dear Xen Users, I have a rhel5 dom0 machine with four nics, two public and two private. My goal is to run two xen instances, a fully virtualized rhel4(with a custom kernel, hence the fully virtualized) and a paravirtualized rhel5. Each instance will need one public and one private nic with gigabit connectivity. At the moment I''m simply bridging two nics to each instance. Is this the

Hello everyone. What's better for Asterisk: have 2 distinct 100Mb network cards in the system, one on the "internet" and one on the "local net" OR have one 1000Mb network card with 2 separate VLAN's set up? It's a difficult decision because 2 cards are using 2 IRQ's etc but a single 1000Mb card might generate more PCI interrupts and get me into different

Hi Folks, Is there any SIP FXS ATA with Gigabit ethernet bridge port, in the market ? -- Isamar Maia Cel. VIVO SSA: (55) 71-9940-2012 Cel. TIM SSA: (55) 71-9289-5128 Cel. Claro SSA: (55) 71-9146-8575 Fixo: (55) 71-4062-8688 Skype ID: isamar.maia "A vida ? muito curta para ser pequena" (Benjamin Disraeli) -------------- next part -------------- An HTML attachment was

Hello I am having a weird issue with a PCI-X Intel dual gigabit ethernet nic. While I am partially successful in pass thru with kvm, I have a weird issue with my pfsense freebsd vm. It see the two nics but gives them the same Mac address. I'm not sure if this is a pfsense bug or what. The nic works for everything but this Mac address issue. Long story short, I guess what I'm asking is

> > Attempting to install CentOS on a new MSI MB (MS 9618), which > uses the subject controllers. > There are two controllers on the board, seems as though only > one can be used. > I have to manually init, using ifconfig eth0, to use it. > > I understand that the Ethernet controller drivers are not available. > Is there any news on this or a possible date when

Hi list, Im having a problem with intel 82573L Gigabit Ethernet Controller. Centos 4.2 can't detect this internal ethernet port my motherboard is an Intel Desktop Board D945PSN. when i type lspci the ethernet is identified but when i type dmesg i can't see the ethernet port. -- Regards, Mark Quitoriano, CCNA Fan the flame... http://www.spreadfirefox.com/?q=user/register&r=19441

I can not disable the auto-negotiation (eth1) on my centos 6.2 via ethtool or /etc/sysconfig/network-scripts/ifcfg-eth1 the eth1 is a private network on a cheap gigabit-switch (under controll from a serverhoster). sometime the ethernet-card lost the "speed" and "duplex" information and change it to "unknown". i can only fix this with a network-restart (or

On 1/1/2015 9:41 PM, mechy2k2000 wrote: > Hello I am thinking of buying this card to and wanted to know if this NIC > is supported. The card is a Sun Microsystems PCI-X Quad-Port Gigabit > Ethernet Adapter QGEXPCI 501-6738-10. Can't find any info on how well the > card plays with centos and also proxmox ve (if any of you use that distro ) I've not tried that card on anything

Hi All, I am currently using Samba v3.0.14a and it's incredibly responsive...except when it comes to large files. Currently my specs are as follows: Santiago Dell PowerEdge SC1420, which is using SATA (RAID 5), and reiserfs 3.6 Ottawa: Desktop PC Windows XP 100/10 Ethernet Card. Douglas: Desktop PC Windows XP Gigabit Ethernet Card. These are the tests that I have performed: Test Set 1:

Do anyone have any experience using 10 Gigabit Ethernet connections with Samba? Specifically, if you have had such an experience, can you share what sorts of optimizations you made to get the maximum data transfer between server and workstation? I am just experimenting with this kind of setup myself and I see a huge GULF between the raw TCP/IP transfers that I can make between two

I got a new USB ethernet adapter from ebay, the ad said RealTek chipset, so I thought I would chance it. Well, my 5.2 system does not recognize the USB device. At all. What do I need to do? I checked the driver CD and the XP driver directory's .inf file has the following: ; ASIX AX88172 USB2 to Fast Ethernet Adapter * ; * ; Copyright 2001-2003,