similar to: My Back-UPS RS 1000 went haywire, any ideas?

Is the battery old? PbAc ones usually last for 2-3 years and then degrade. Should be a field-replaceable part. Some 20 years ago I had an APC BackUPS become a glorified power strip every few years, so when the wall power disappeared - load went down immediately. It was also beeping about battery replacement (but in the closet, was not often noticed quickly). This is also a way for you to check if

hi all, i was running the previous RPM (samba-2.2.8a-2_rh73.i386.rpm) and have just upgraded to the 3.0.0-1. everything seemed to go smoothly. when I try to mount my media share from my other linux box, I get the following error: 1639: tree connect failed: ERRSRV - ERRbadpw (Bad password - name/password pair in a Tree Connect or Session Setup are invalid.) I'm still running against my old

All, Experiencing some issues on my FXO lines. If a call comes in on an FXO and then get transferred to another FXO (say to call someones cell phone), those two lines will stay tied together indefinitely. This happens to us when we transfer an incoming call to our on call guys after hours and on weekends. We have installed 3 other * boxes and they do the same thing. We use a Adit Channel bank

For my Smart 2200, a charged battery string is anywhere between 25.6 and 26.8 volts. I'm seeing nut report 13.0 volts, which seems suspicious. Even if the UPS were reporting half of the actual battery voltage to keep protocol compatibility with models having a 12V battery system, the value of exactly 13.0 seems unlikely. According to the page at

Leslie, This message is most appropriate for the NUT user list. I kept Rik Faith's and Nicholas Kain's copyright information because the tripplite_usb driver borrows heavily from the tripplite (serial) driver, but they are not responsible for the mess that I made in the USB driver. See below. On Dec 28, 2008, at 5:28 PM, Lelsie Rhorer wrote: > Gentlemen, > >

Ok... I asked a question a few months back about a 7960 that a user claims to be "shocking" her in her ear from time to time. A few others indicated they had similiar issues and alot of them seemed to stem from power over ethernet. Here's what we've done... We replaced the phone, ran two new cat5 cables to a different switch, put in a power brick and disabled power over

On December 2, 2018 7:29:38 PM GMT+02:00, raul <raulvior.bcn at gmail.com> wrote: >I have restored original configuration and enabled the ignorelb flag. I > >didn't point out in the original e-mail that after every poweroff the >battery percentage is reported at 40% instead of 100% and charges >slowly again to 100%. Maybe the UPS sends a LB event and shuts down

Hi All, I have what is probably a 12 year old (or older) Compaq R3000 UPS plugged into a FreeBSD 8 system running NUT version 2.6.5 This UPS contains a total of 16 batteries in 2 banks of 8, each battery is 6 volts and the bank produces 50 volts. The UPS monitors battery voltage and the battery charger in the UPS works like this. For about 2 days it will apply a charge/float/topping

Hello, Somewhat off-topic, but seeking some input from other tech folk on this list. I have a Tripp-Lite SMART 2200 (a white tower that looks similar to, but predates the black SMART2200NET) that just failed its monthly battery test so I bought new batteries and replaced the old ones. Sadly once put back together, plugged in and enabled it did not power up--no lights, sounds, smoke, etc. I took

Hi, I have had this issues for ages but have ignored it, but my handsets get faint background crackle on the FXS port. When I connect the handset directly into my PSTN, it goes away complete, so I am generating this from somewhere in my asterisk box. I get it immediately when the phone goes off-hook and it stays through the dialing and call progress. I can't think of any other devices

Hi: I'm using a TDM-400 to terminate PSTN lines at my Asterisk server with kewlstart signalling. When an outside caller calls the server, the TDM-400 goes off-hook and provides a ringing tone to the caller. If the caller hangs up before the receiving party answers the phone, Asterisk fails to detect the hang-up. The TDM-400 stays off-hook, hogging the line, while Asterisk rings the

Hi - I have an fairly vanilla answering machine (actually its a combo cordless phone/answering machine) attached to an FXS port (on a TDM400 Card). Everything is working as planned except I seem to be having a bit of trouble with the answering machine. After is answers it plays the outgoing message and then hangs up before letting the caller leave a message. (it actually hangs up before the

Hi After a few days of very fine work, my dom0 went mad. (using xen-3.0.2) It''s ksoftirqd keeps 70% of cpu all the time. Is there anything I can do? Regards, Steffen begin 666 smime.p7s M,( &"2J&2(;W#0$''`J" ,( "`0$Q"S )!@4K#@,"&@4`,( &"2J&2(;W#0$'' M`0``H(())#""`JPP@@(5H ,"`0("`P]Z''3

I have the same issue of incorrect output voltage being reported by usbhid-ups, as run on NAS4Free (FreeBSD). UPS is as shown below. There is a thread on this list from 2014 that has these same issues, apparently never addressed by any of the later usbhid-ups releases. I?m using 2.7.3. The value I am especially concerned with is the output voltage; if ANY thing should be right on the report, it?s

Hi, I just got and setup a new ip500 yesterday and it worked for about 15 minutes. Then it froze during a reboot.Now, when power cycled, the logo comes on for 3 seconds and then the screen is blank and nothing further happens. 468* factory reset doesn't work. I am about to send the phone back, but wonderd if anyone had a suggestion first.

I am trying to obtain optimum gain settings for a bank of analog lines connected to a channel bank. My telco has provided a 'Type 102' test line to use for incoming level calibration. This is functionally equivalent to app Milliwatt(), but provides tone from the CO inwards. Question is, how should one use this a 0dbm test source with ztmonitor? Am I correct in understanding that a 0dbm

Hello people, I am having difficulties figuring out the POE power draw in watts from a Polycom IP601. I want to know how many IP601's can be powered from the Cisco Catalyst 3560G-48PS. The IP601 wallwart has: Input 120VAC 60hz 19W, Output 24VDC 500mA. I assume the output is appropriate value to figure out how many phones can be powered. The Cisco 3560 datasheet says "the 48-port PoE

Hello! Given the current discusison regarding ztmonitor, line testing, etc., I've been looking into purchasing a used transmission test set. From my research, it seems that there are two items that might fit the bill: the HP 3551A and the HP 4935A. I know nothing about these specific devices. I *do* have a good background in electronics, and I understand the concept what they're

Hello, I have the Cyberpower USB CP550SL RT< whats its called when i bought it :) (AE550 according to upsc) and i think its missing some monitor options such as load, wattage use, temp..etc (shows in powerpanel pro,personal ed under win) ..it seem to be really lacking the only options i get are battery.charge: 100 battery.charge.low: 10 battery.charge.warning: 20 battery.runtime: 4560

Hi Folks, Does anybody have experiences with plugging 3 TDM400P cards in one PC?? I think about a Asterisk box handling 8 incoming analogue lines and providing 4 lines to an old analogue PBX. I read a lot about trouble with the TDM400P cards so this idea seams to be not really god, or? Ciao Joerg -- _____________________ Don't PANIC