similar to: How Shorewall acts on localhost traffic

I''ve set up shorewall with the two-interface mode. pc #1 eth1 ---> ppp0 ---> Internet eth1: 10.10.10.254 eth0: 10.10.10.1 > via a crossover cable pc #2 eth0: 10.10.10.2 (gateway=10.10.10.254) I am able to surf the net with pc #1, but pc #2 is completely cut off from pc #1 and the net. I am also unable to ping from and to pc #2.

Hello, Which port Smb4K uses? I am not able to use Smb4K on my server for the local network. Thanks Varun

Hello, I''m a very happy user of shorewall but I have found a problem or maybe a misconfiguration I made which I can not resolve. I use a fairly large blacklist based on probes, nimda & codered attacks, proxy & relay probes etc. The only problem is that I want to block incoming trafic on all ports FROM a block but it does also block a httpd, ping etc TO a ip in a block what I do

How does one interpret the mac addresses in the log which seem to have 14 segments... Example, this appears in the log... 00:40:c7:2e:09:c0:00:01:64:4a:70:00:08:00 Yet I can''t find that in the arp table norcomix:~ # arp -an ? (192.168.2.148) at 00:10:4B:6A:AE:E7 [ether] on eth1 ? (192.168.2.149) at 00:D0:B7:1D:F2:F2 [ether] on eth1 ? (24.237.19.16) at 00:10:DC:67:BA:80 [ether] on eth0 ?

Since you''ve started signing your email, Tom, my machine can''t verify your sig. Where are you publishing your key? -- John Andersen - NORCOM http://www.norcomsoftware.com/

First of all, My apologies for this maybe slight OT post, but I have so much confidence and read so much good replies on this list, that I am still asking my question. I''m looking for a linux distribution to use on our school''s homemade routers. The routers are small miniITX based systems with 2 network interfaces. I added a 4 port D-Link network card in some cases, when I

Hello, I want VNC Server,which is outside my network ,add my VNC Client, which is behide shorewall box. How should I config the rule? TIA Thongchai

Hola and thanks for any help in advance I installed mandrake 9 a few days ago and wanted to set up some additional rules to shorewall, bu i failed :) What i want to do is basicly route any incomming udp and tcp packets on port 4665 to a workstation behind the router. router with mandrake 9, eth0 (192.168.0.1) internal net, eth1(10.0.0.0) connected to dsl modem and gets a dynamic ip

Ok this is admittedly OT, but when you want network advice you go to where network gurus hang... When popping mail from my primary mail server (Linux) from my linux laptop a simple mail check takes 15 seconds to connect when using a wireless nic (802.11g) and 1 second using the hardwired nic. Popping my backup mailserver (also linux) which is sitting RIGHT BESIDE the primary takes one second

Hi, I''m a home user who doesn''t understand the workings of the Shorewall firewall (or the linux OS on which I''ve just installed it) very well. Having just installed Shorewall 1.4.6c with a default "home user" configuration I gave it a run against the online ShieldsUp scan. Main surprise was that the ICMP echo was enabled. I''ve since gone into

Dear all We are using a definition of rules which has perfectly worked with SuSE8.2 and vmware and a local samba on some clients. The systems got an update to 9.2. Now we got a very strange problem which probably could belong to an firewall definition problem. After booting of the system the samba connection to vmware works perfect but a few hours later it isn''t possible to copy a

Whilst configuring another shorewall firewall router for another site, I must have made some totally newbie error.... While directly on the cable modem, it works great. But when placed on the LAN side of my existing Shorewall box, the NEW shorwall box could not ping, or look up dns or anything else. If I shutdown shorewall (clear) in the NEW box then it could surf the net and ping etc. When

I am making a new box to test with and was trying to install shorewall via rpm. So I download the shorewall 2.2.5 rpm and issue a rpm -ivh shorewall-2.2.5-1.noarch.rpm. I then get an error: error: Failed dependencies: which is needed by shorewall-2.2.5-1.noarch So as you can see there are no dependency issues. I thought I saw this on the mailing list a while ago but I just searched for it I did

I''m using shorewall 2.0.x at home as an Internet gateway for family. However my brother always plays online games overnight, so my parents asked whether I can do something on the gateway to control the time of accessing the Internet. I planned to put a script on crontab to schedule which it will execute say at 12:00 night daily, the script will execute a command will deny my brother

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 DeveloperCube is a new project started by veterans of the web development industry. We are proud to announce that we are now the Official Shorewall Support Forum. We are an online community offering discussion geared towards web developers, designers, and administrators of all skill levels. There are topics ranging from how to market your website,

Happy New Year to everyone: I have followed the instructions at shorewall.net/samba.htm. I''ve restarted the samba server, shorewall, rebooted, everything. And from my network I cannot browse available shares on the firewall (192.168.1.1) telnet 192.168.1.1 138 fails with connection refused, which I don''t understand. All other open ports respond with a string. -- Philip

I want to run dhcp and shorewall on the same computer.It is my gateway and that computer doing NAT for my network.How can I set up shorewall to let only users that get theire static ip address via dhcp, not to let users that had static address.

I will be off of the list until sometime Monday afternoon (Monday is a holiday here in the US). -Tom -- Tom Eastep \ Shorewall - iptables made easy Shoreline, \ http://www.shorewall.net Washington USA \ teastep@shorewall.net

A violent wind storm is expected in western Washington state later today and such storms often produce power/communications outages. I''ll do what I can to keep things running here. -Tom -- Tom Eastep \ Shorewall - iptables made easy Shoreline, \ http://shorewall.sf.net Washington USA \ teastep@shorewall.net

Hello, I am not able to open the web interface for the wrt54g router on the lan. Which port does it use ? Thanks Varun