similar to: UPSilon 2000 via USB linux

THANKS, but the 'megatec' driver only works whith windows OS via USB, and i need it for red hat OS with USB-serial connection... Please, anybody can help me.... nut-upsuser-request@lists.alioth.debian.org escribi?: Send Nut-upsuser mailing list submissions to nut-upsuser@lists.alioth.debian.org To subscribe or unsubscribe via the World Wide Web, visit

Hi to everyone! I'm posting here after digging around the nut-upsuser and nut-upsdev mailing list, hoping I didn't miss something important. I'm trying to make my ups working with nut: it's a Tecnoware ERA LCD 0.85 which uses the so-hated UPSilon 2000 software to connect via usb. Personally I checked and seems that this junk software only works from windows, I'm trying to

Hi all, Currently, the "megatec" driver only supports UPSes which have a serial (RS232) interface. However, I'm under the impression that most of the models that speak the megatec protocol, and have an USB interface, just have a standard serial-to-USB converter inside. This being the case, there should be a "/dev/ttyUSBx" device which the megatec driver could use just as

Hi all, Currently, the "megatec" driver only supports UPSes which have a serial (RS232) interface. However, I'm under the impression that most of the models that speak the megatec protocol, and have an USB interface, just have a standard serial-to-USB converter inside. This being the case, there should be a "/dev/ttyUSBx" device which the megatec driver could use just as

Hi, i just got a Phoenix Technologies PH1200UPSB 1200va serial-port ups and it is only partially supported by bestups driver (needs manual ID or driver rewriting). It comes with a tool called UPSilon 2.1 on a CD (which worked better with TERM=linux). After [sl]tracing it i came to these results: COMMANDS : - Command: I Response: "#XPHOENIX TECH PH1200UPS VER2.00C " - Command: F

Hello! I'm not a very happy owner of "Designed in Italy and manufactured in China" Tecnoware ECO LCD 650 UPS. Plan was to use it with FreeNAS 8 on HP Microserver... But this plan gone bad. I want to ask you to look at another "Megatec USB" protocol implementation. This UPS controlled by UPSilon 2000 program (Windows OS). Protocol type Mega(USB). Bad things: - Program does

On 10/08/2012 21:58, nut-upsuser-request at lists.alioth.debian.org wrote: >>> Arnaud Quette<aquette.dev<at> gmail.com> writes: >>>> 2012/6/3 Chris Rees<crees<at> freebsd.org>: >>>>> Hi all, >>>> Hi Chris, >>>> >>>>> After some research I've found that this device should run with the

Hi there! I'm a n00b NUT user trying to get it running on RHEL5 and actually do something useful for me. Few questions: 1) I want it to notify me by email on power loss and power back events. I can't find any sample scripts for this purpose... Where shall I look for them? 2) So far, I've backported the package from Fedora and got my Ablerex running (previously used with Upsilon /

Hello, I've recently bought two cheap UPS (http://www.ldlc.com/fiche/PB00109242.html). They're not supported natively by NUT (even though the monitoring software is UPSilon from megatec). After some investigation, they almost use the krauler-type communication already supported in the blazer_usb driver. However, the UPS won't reply if the language ID is not 0x4095... Therefore, I

Hi to all! Path send by Brian R. Smith with subject "[Nut-upsdev] Dynamix 650 VA USB - broken, have rough fix" really works! Tested with no-name UPS (works with UPSilon 2000 Windows software) and has USB vendorid=0001 productid=0000 Please, add it to the main branch of blazer_usb.c I belive that several users agree this.

Hi I have been searching the wiki and mailing lists and I cant see where my config is incorrect. I have a Digium tdm11b (1 fxo + 1 fxs) this is the output of cat /etc/zaptel.conf # Autogenerated by /usr/local/sbin/genzaptelconf -- do not hand edit # Zaptel Configuration File # # This file is parsed by the Zaptel Configurator, ztcfg # # It must be in the module loading order # Span 1: WCTDM/0

Hi, This is my first post ever on a technical forum, so please forgive any poor etiquette etc. Also I'm totally new to Linux all of my experience has been trying to get this UPS to work. So please bear this in mind. I'm running OpenSuse 13.1 and I have a Lupus 500 USB (Fideltronik) After quite a bit of playing around I managed to get the status of the UPS using the blazer_usb driver and

I'm afraid that I am at a loss here. I am new to Asterisk, and have successfully set up SIP. But I cannot get my FXS card working, and I'm not sure what else I can try. # modprobe wcfxo /lib/modules/2.4.21-37.0.1.ELsmp/misc/wcfxo.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may

Hi, I am struggling to get rid of a conflict on DELL 2800 : PCI Parity error (EB113 on the display) I am learning linux and asterisk as I go along, there might be obvious things I should know, but bear with me. >From demsg below my 2 digium cards installed are listed (no config or connections done to digium cards yet), the conflict is with the TDM400P card, without that card, in any slot, no

Hello everyone, has anyone ever tried to make this device work with Linux and NUT? This is what udevadm monitor says: UEVENT[1215983089.652345] add /devices/pci0000:00/0000:00:0f.2/usb1/1-1 (usb) UEVENT[1215983089.652427] add /class/usb_endpoint/usbdev1.4_ep00 (usb_endpoint) UEVENT[1215983089.657975] add /devices/pci0000:00/0000:00:0f.2/usb1/1-1/1-1:1.0 (usb) UDEV

Sorry for the huge delay and thanks Charles for taking care of this topic. >> I'm running OpenSuse 13.1 and I have a Lupus 500 USB (Fideltronik) >> >> After quite a bit of playing around I managed to get the status of the UPS using the blazer_usb driver and running NUT 2.6.5. >> But unfortunately none of the Instcmds such as load.off etc. worked. > > Can you post

On 1/23/07, Henning Brauer <hb-nut@bsws.de> wrote: > good new first: the megatec driverin 2.0.5 now works with the Online > Xanto S3000R here - well, for the very basics. > > the UPS has NO way ofidentifying itself. It also does not respond to > the power ratings query ("F"). I previously used a hacked up fentonups > driver. This means the driver cannot figure out

On Jun 9, 2014, at 6:40 AM, Hill wrote: > Hi, > This is my first post ever on a technical forum, so please forgive any poor etiquette etc. > Also I'm totally new to Linux all of my experience has been trying to get this UPS to work. So please bear this in mind. No worries. On the NUT lists, we don't set or alter the reply-to header, so please use "reply all" to make

Regards I am installing NUT for the UPS Skate UPS-2200D, the UPS have conection with USB to PC and i have problems to configure nut the ups is conected and Linux report this config Aug 19 23:34:56 dakota kernel: [22393.099595] usb 2-2: new low speed USB device using uhci_hcd and address 7 Aug 19 23:35:06 dakota kernel: [22403.186326] usb 2-2: Product: MEC0002 Aug 19 23:35:06 dakota kernel:

Sorry for my delay, I've only just read this mail. At first glance the driver looks like it should work, I will test it tomorrow (if possible) and let you know. I'll also give a reply to your questions. Many thanks for the work you've already put into this. -------------------------------------------------- From: <hyouko at gmail.com> Sent: Monday, June 30, 2014 12:42 AM To: