similar to: APC/MGE and NUT support

Hi, I regularly have errors (kernel: dst cache overflow) and crash of a firewall under Linux 2.6.17 and the route patch from Julian Anastasov. With rtstat I see that the route cache size increases regularly without never decreasing. I have this parameters: fw:/proc/sys/net/ipv4/route# grep . * error_burst:1250 error_cost:250 gc_elasticity:15 gc_interval:60 gc_min_interval:0

Hi, I use for a customer a Linux router/firewall with 1 internal interface connected to the LAN and 3 external interfaces connected to 3 different ISP. I use a kernel 2.6.17 with a routes patch from Julian Anastasov. I mark outgoing FTP traffic for the routing. With the rules below I do not have a problem with the active/normal FTP to connect on FTP server. But the passive FTP does not pass

Hi, I have a computer which is used as router/firewall/VPN with four network card. One connected on the LAN (br0, 10.0.0.0/24), the three others to three different ISP, eth0 192.168.1.0/29, eth1 192.168.0.0/24, eth2 192.168.2.0/29. This computer is under Linux 2.6.11 with the Julian Anastasov routes patch. The configuration by default is to balance the load on the three interfaces. Then, I

Dear folks, According to mge-mib.c (NUT 2.6.2) LB condition is gained from variable .1.3.6.1.4.1.705.1.5.14.0 (i.e. upsmgBatteryLowBattery.0). The test device of me does not set this variable to yes(1) even if runtime drops below the preconfigured limit. I complained about this at Schneider Electric. They replied that low battery status is indicated by .1.3.6.1.4.1.705.1.5.14.0

Hello, I forgot nut since more than a year because a lot of job with other application My server nut failed since severals months We had 3 electric failure so I must install a new server nut I work with ubuntu 10.04.4 (64bits) / I installed nut 2.4.3 with deposits I have a MGE Pulsar evolution 2200 connected on usb last week when I began my tests all was ok (communication etc etc ..)

I'm struggling to configuring nut for MGE Pulsar Ellipse 800 (at least Ellipse 800) for two boxes - home firewall and file server. I'm using Debian 4.0 Etch, every one of them. I'm built (after some dangerouse experiments) a testing configuration, where boxes are plugged to line, server playing as a master, firewall as a slave, and UPS connected to an electric heater about 300 Wats (no

Hello, At my workplace I have exact UPS config as stated in the subject (APC MGE Galaxy 5500 + AP9635CH). I have it set up to work with snmp-ups NUT driver. Despite many readings from *upsc* command I am not receiving "On Line Status" (ups.status OL) nor "On Battery Status" (ups.status OB) and therefore I can't get my systems to shutdown during a power outage event.

mateuszx via Nut-upsdev <nut-upsdev at alioth-lists.debian.net> writes: > At my workplace I have exact UPS config as stated in the subject (APC MGE > Galaxy 5500 + AP9635CH). > I have it set up to work with snmp-ups NUT driver. > Despite many readings from *upsc* command I am not receiving "On Line > Status" (ups.status OL) nor "On Battery Status"

Hello, At my workplace I have exact UPS config as stated in the subject (APC MGE Galaxy 5500 + AP9635CH). I have it set up to work with snmp-ups NUT driver. Despite many readings from *upsc* command I am not receiving "On Line Status" (ups.status OL) nor "On Battery Status" (ups.status OB) and therefore I can't get my systems to shutdown during a power outage event.

Also, which version of NUT is involved? There were recently PRs (merged to master-branch, eventually will be in 2.8.1) about more SNMP-UPS support including APCs e.g. 1674, 1679, 1113 (should be in 2.8.0)... Many distros still ship 2.7.4... Jim On Tue, Feb 28, 2023, 00:57 Greg Troxel <gdt at lexort.com> wrote: > mateuszx via Nut-upsdev <nut-upsdev at alioth-lists.debian.net>

Hello My server with another UPS (MGE Pulsar Evolution2200 USB) is OK. All scripts work Is it possible to work with a UPS MGE CometExtrem 6 on serial port Which driver can I use ? I tried with mge-shut ou mge-utalk without any success when I start driver with upsdrvctl with mge-utalk I have (after a long time) Can't connect to UPS [MGE_cometEX] (mge-utalk-MGE_cometEX): No such

I've got an update on this case Using tkmib I discovered that my UPS (NMC per say) sends its state by OID 1.3.6.1.4.1.318.1.1.1.11.1.1.0 .iso.org.dod.internet.private.enterprises.apc.products.hardware.ups.upsState.upsBasicState.upsBasicStateOutputState.0 = 0001010000000000001000000000000000000000000000000000000000000000 (mib used for this snmpget was powernet441.mib) (I got a description about

Hello, I''m starting at the RR, and I''m trying to use google charts to generate some graphs in a single plugin in rails. But I''m testing the samples that are giving errors. I think it must be configuration error. Someone who has used google charts on rails help me? Since already thank you! Juliana. =================================================================

Hi, I'm forwarding your mail to the NUT list, because of a lack of time, and also since some others (Charles) already looked at this issue IIRC (related to the development branch 'netport'). cheers, Arnaud -- Linux / Unix Expert R&D - Eaton - http://powerquality.eaton.com Network UPS Tools (NUT) Project Leader - http://www.networkupstools.org/ Debian Developer -

Dear Sirs, I have an old but very well-working UPS MGE Pulsar ESV8+ Rack. I'd like to use it to power FreeBSD 9.0-Rel server. Of fortunately I have problem with recommended driver - mge-utalk, nut 2.6.4 (installed from FreeBSD Ports). I get messages: Could not get multiplier table: using raw readings. and updateinfo: Cannot update system status I saw similar thread on mailing list with no

Hello, I recently had a failure with my old MGE ESV8 ups, it just died on me so I had to get a new one. I found a MGE ESV8+ cheap and everything seems to work fine with it except the communication with the computer. The old ESV8 (non +) worked fine with NUT after applying some patches I got from the mailing list, but I think they are in the source tree now. I'm using the same cable that

Hi, I've seen a few emails in the archives about problems polling MGE UPSs via USB under FreeBSD, but unfortunately I didn't find a solution in them that works for me. A few details about my setup.. The UPS is a MGE Nova AVR 600 connected via USB to a FreeBSD 6.2 box. I have tried both the nut port (2.0.5) and the svn trunk but have had no success yet. I am running nut as root to

Hi, I've seen a few emails in the archives about problems polling MGE UPSs via USB under FreeBSD, but unfortunately I didn't find a solution in them that works for me. A few details about my setup.. The UPS is a MGE Nova AVR 600 connected via USB to a FreeBSD 6.2 box. I have tried both the nut port (2.0.5) and the svn trunk but have had no success yet. I am running nut as root to

Hi all, First of all thanks for the great work on nut ! (despite it's not fully functional yet overhere). Everything seemed to go fine until the final test : shutdown the UPS ! The system is running FreeBSD 5.3, the UPS is MGE Ellipse 800 USBS both linked with the MGE serial cable. The system is a remote server, only running some file services and large disks. The porting,

hello, at first I'm sorry my english isn't perfect but I tried to be clear I work with mandriva 2007 and with nut 2.0.1 installed with urpmi my UPS is a MGE Evolution 2200 connected with RS232 in my ups.conf I try to use mge-utalk driver and also mge-shut both seem to work I don't really known which I add to use It's the first point. As I saw on web site, I add maxage 25 in