similar to: Asterisk 11.9.0 PRI no ring indications

I am having a problem with a new PRI turn-up on dahdi 2.5.0 and asterisk 1.8.5 that I have not seen before. The PRI is setup as B8ZS, ESF and the span shows up and ok. This PRI is merely a crossover T1 going into an old DC0 class 5 switch. I am getting the following errors over and over again [Aug 16 10:26:10] NOTICE[8002]: chan_dahdi.c:3043 my_handle_dchan_exception: PRI got event: HDLC Bad FCS

Hey Guys! Please help me to find out issue. I have two PRI ## Span 1: WPT1/0 "wanpipe1 card 0" span=1,1,0,esf,b8zs bchan=1-23 hardhdlc=24 echocanceller=mg2,1-23 ## Span 2: WPT1/1 "wanpipe2 card 1" span=2,2,0,esf,b8zs bchan=25-47 hardhdlc=48 echocanceller=mg2,25-47 Sometime my calls got through but some time i am getting pri cause 44 sebpbx1*CLI> == Using SIP RTP

Hi, I have a client that has a 24 channel voice T1 that I have been using e&m signalling over for a number of years. The local telco finally got an ISDN switch and wants to move them to PRI. I didn't see this as a big problem - I've done a few others on this particular Caribbean island without issues, but this would be the first time with a Xorcom unit involved. We tried to do

Hello all. I have an NEC PBX connected via a TE210p E1 line to an asterisk 1.6 box. NEC -> E1 -> TE210P:1 -> * -> TE210P:2 -> E1 -> Telco Incomming calls from the telco to the asterisk box to the NEC work fine with indials and everything. Works sweet. Outbound from the NEC to the Asterisk box fail. Giving an long dial tone that then times out. Ie, pick up NEC handset, dial

Hello, i have succesfullu setup asterisk with Sangoma E1 card, evrything works well but i don't know how to pass indications from telco switch to the user - when users call bad number telco switch shuld talk "unallocated number" but its only send PRI_CAUSE 1. How to pass voice indications thru asterisk to clients? My /etc/zaptel.conf: span=1,0,0,CCS,HDB3,CRC4 dchan=16

I have a system setup with two T1 circuits, the customer complains of call quality issues. I've checked logs and don't see anything too strange, but when I run "dahdi show status" I see: Description Alarms IRQ bpviol CRC4 Fra Codi Options LBO T2XXP (PCI) Card 0 Span 1 OK 0 0 19 ESF B8ZS YEL 0 db

I have been getting quite a bit of PRI Resets using my Quad PRI Digium card. Prior to the resets I am getting similar notices to the following chan_zap.c:7482 pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 3 Telco claims the PRI's are fine on their end and that it is my unit. Is this timing? (google somewhat leads to this) I am running 1.08 asterisk zaptel

hi folks. i recently setup an Asterisk system in Hong Kong. their phone company told me that their T1 PRI switch type is Primary-NTT. however in chan_dahdi.conf there's no such option. i have it set to national. it worked fine for a while, but now suddenly stop working. in coming call just keep ringing and didn't even show up on console. out going call hang up immediately with cause code

Out of the blue i started receiving the following error on my PRI line which connects my asterisk server to a Norstar 0x32 key system. The asterisk zaptel.conf file was configure as follows and this config worked for 6 months until friday. Nothing was changed on either system prior to friday. here is teh zaptel.conf span=1,0,0,esf,b8zs bchan=1-23 dchan=24 span=2,0,0,esf,b8zs bchan=25-47 dchan=48

We've been working for the past 2 weeks to get a new V400P working with our PRIs from the telephone company. We're trying to get the Asterisk server setup as a VoIP gateway for SIP and AIX. We can make SIP-SIP calls, but all calls from or to the PRI fail. This is the applicable entries from the Asterisk log (configuration files follow) for a call coming from the PSTN on the PRI. I

Hello, I have been struggling with the configuration of this card on my box. I have a T1 line and I am trying to setup asterisk with it. I followed all the instructions and I still see a blinking red light on the card. I use fedora 12. If everything is fine should I see a green line when I plug in the T1 line ? I want to isolate the issue so I di not start asterisk. When I run asterisk I get

I'll keep asking weird questions here: I have two T1 WAN circuits originating at my asterisk box and terminating at Asterisk servers at remote sites. Currently I use zaptel ppp assigned to all 24 channels for data. Now I would like to split off a few of these channels for voice trunks (I should use VOIP, but at the moment I do not have fast enough servers for the codecs) At one site

On Sat, Jan 17, 2015 at 09:31:33AM +0100, Bertrand LUPART - Linkeo.com wrote: > >>> However, dahdi_genconf keeps finding no span: > >>> What am i missing? > >> > >> It looks like your driver is loaded correctly. My guess would be maybe > >> the dahdi-tools is packaged as an older version that doesn't know > >> about the newer te435

Hi again, I'm trying to setup our non pri T1 (they call it a Long Distance T1), our current pbx has the signaling set to E&M, I can set em in zapata.conf, but I'm trying to track down the proper entries for the zaptel.conf file. The digium docs only show a PRI example. Our current system has these settings: Signalling: E&M Framing mode: ESF Line Coding: B8SZ here's my

We are currently working to trunk from a Nortel 81C to an Asterisk Server 1.4 running on Red Hat Linux. We have two PRI trunks which work with the exception of the clock slips, which is causing the Nortel to reset the PRIs once a hour. Thanks for any suggestions. 81C MSDL Asterisk Digium TE110P REQ prt TYPE adan dch 10

I need some help getting a system running for one of my company's plants. I am running AsteriskNow 1.7 with Asterisk 1.6.2.10 and FreePBX 2.8.0.2. My D-Channel keeps bouncing. The telecom tech told me he thought that I might be using the wrong sync source, and I think I might have been, but I changed DAHDI system.conf to "span=1,1,0,ESF,B8ZS" (from

I am ordering T1-PRI service from local service provider and have a few questions. Is there framing and coding considerations (or is it all one standard), if so what is best? How are calls routed based on DIDs - are these just dtmf tones passed after the call is picked up and treated as normal exten=> definitions? John This e-mail was scanned and found clean by Monroe-Woodbury CSD

I have just finished installing a new asterisk box at my work. The box is quite hefty, dual Zeon 2.8s with SCSI drives and 2Gb of memory. I have a 4 port Digium T1 card for channel bank and PRI access. I activated a PRI from a local CLEC (DMS-500 based, National protocol). This PRI is on slot 2 of the card and is set as the primary timing source. It is ESF/B8ZS. All the software is latest

Okay, now I am really confused. I have two PRI's coming in from two different Carriers (QWEST and ELI), both of them are supposed to be setup to pass name and number on incoming calls. Problem that I am having is that I am not receiving inbound caller id name on either PRI, the only thing that both carriers have in common is that I am terminating into a DMS switch at the carrier.

> > >>SF framing is called d4 in the zaptel.conf. > > Thanks. > > Don't forget this will be ami and not b8zs. You have to use esf to > get > b8zs. This is not true. Line coding and framing are two different things and any type of line code can be used with any type of framing. - Line coding - AMI, B8ZS (there are others but I have forgotten them) - Framing -