similar to: Tripp-Lite OMNI750ISO

On May 8, 2018, at 10:05 PM, Charles Lepple <clepple at gmail.com> wrote: > >> I'm new to this, so let me know what you need from me and I will try my best. This UPS does power our production servers, so shutting things down aren't an easy task, but this weekend might open up some opportunity for that if need be. If I need to test it by unplugging the main power, that I can

Greetings to all, I recently connected a Tripp Lite SMX500RT1U unit to a Synology NAS (basically a Marvell ARM equipped box running a custom 2.6.24 Linux). I tried using the tripplite_usb driver contained in nut 2.4.1 with not much luck. It does read the model ID and VA rating properly, but fails at everything else - mains voltage (this is a 230VAC EU model), battery config, unit status etc.

Device manufacturer and name: Tripp-Lite OmniSmart500 upsc output: matt at backup:/etc$ sudo upsc tripplite battery.charge: 100 battery.test.status: Battery OK battery.voltage: 14.56 battery.voltage.nominal: 12 device.mfr: Tripp Lite device.model: OMNISMART500 device.type: ups driver.name: tripplite_usb driver.parameter.pollinterval: 2 driver.parameter.port: auto driver.version: 2.4.3

Hi, I am trying to configure my Tripp Lite SU5000RT3U on Ubuntu 18.04 as I am not able to completely get all the data from the UPS. After installing all required packages from the Ubuntu repos (had to run sudo apt-get install dkms, I had to install the displaylink drivers from displaylink.org by doing sudo ./displaylink-driver-4.2.29.run, and I created a sim link by doing the following: sudo ln

Hello Charles, Thanks for the feedback. I will try to answer some of these questions: > 09AE/0001 is essentially a USB-to-serial converter, and is not > compatible with usbhid-ups. (Theoretically, we could have a companion > driver that talks the same protocols over a real RS-232 port, but the > hardware I used to develop the tripplite_usb driver only has a USB > port.) Ah, that

On Thu, Jun 26, 2014 at 10:20 PM, Steve Ballantyne <steve.ballantyne at gmail.com> wrote: >> However, we don't have all of the 09AE/0001 protocols decoded in the >> tripplite_usb driver. > > I can try to help out on this front? :-) Definitely. >> > 9.783126 Unknown input voltage range: 0x02 >> > 9.783308 Unknown number of switchable

Hello Charles, Thank you for all of your help this far. I have made some great progress. I was hung up with all sorts of USB problems which we can chalk up to a "blonde moment" for me (or more accurately, a *bald* moment). In all my starting over and screwing around, I had forgotten to reinstall libusb-compat. Duh! I am now to a point that I think we can dig a little deeper. The

<nut-upsuser at lists.alioth.debian.org> I am doing my best to avoid have to spend $280 for a network monitoring card to put into a $190 UPS just to have some good remote monitoring capabilities. Rather, I would like to monitor my many 1U Tripp Lite's on my network using a Raspberry Pi running Raspian and using NUT. However, I cannot seem to get it working. And I while the hardware

I installed nut from the epel repository on Scientific Linux 7. I would like to get my smart500rt1u working, but # upsc smart500 at localhost gives the following output: battery.voltage.nominal: 0 device.mfr: Tripp Lite device.model: SMART500RT1U device.type: ups driver.name: tripplite_usb driver.parameter.pollinterval: 5 driver.parameter.port: auto driver.version: 2.7.2 driver.version.internal:

Leslie, This message is most appropriate for the NUT user list. I kept Rik Faith's and Nicholas Kain's copyright information because the tripplite_usb driver borrows heavily from the tripplite (serial) driver, but they are not responsible for the mess that I made in the USB driver. See below. On Dec 28, 2008, at 5:28 PM, Lelsie Rhorer wrote: > Gentlemen, > >

Well, I have good news and bad news. I have a Tripp Lite SmartPro UPS attached to a Linux server running Ubuntu 5.10, and I'm running the just-released nut 2.0.3. I had error -71 from the UPS, which Charles Lepple correctly called out as a likely cable problem (thank you, Charles.) The cable provided with the UPS by Tripp Lite was just plain bad. Not too long, mind you- defective. I

Hi, I'm running Fedora Core 6 and need to monitor a Tripp Lite SMART2200RMXL2U. I've loaded the nut-2.0.3-2.1 RPM. The UPS is connected via the provided USB cable, and that much appears to work: # dmesg | grep -i tripp hiddev96: USB HID v1.10 Device [Tripp Lite TRIPP LITE SMART2200RMXL2U ] on usb-0000:00:1f.4-2 # lspci | grep -i usb 00:1f.4 USB Controller: Intel Corporation 82801BA/BAM

Original Message >I have 2 SmartUOS1050SLT's that apparently protocol 3004, has there >been >any progress on getting these units supported under nut? I am running >version 2.4.1, and get the following output when starting the driver. >#lsusb >Bus 005 Device 002: ID 09ae:0001 Tripp Lite ># upsdrvctl -DDDD start >Network UPS Tools - UPS driver controller 2.4.1

Good afternoon, I'm trying without much success to monitor a Tripp Lite OMNIVS1500XL using NUT. I checked the compatibility list and saw that this UPS is supported by tripplite_usb. The system is running Debian Stable, but I've downloaded NUT 2.0.3 and compiled from source since the packaged 2.0.1 doesn't include tripplite_usb. I compiled --with-user=nut. My first attempt at

Test machine: Windows 7 Pro x64, NUT 2.6.5-3 UPS model: Tripp-Lite Internet Office UPS (INTERNET525U) I needed a UPS and I had this old, but lightly used Tripp-Lite in storage. On the compatibility list I see a (?similar?) INTERNETOFFICE700 using the tripplite_usb driver. But the driver is not liking this particular model that I have. I'll be receiving a 3S550 soon, so I'm not

Using this UPS in the UK on 240V mains. Connected via USB: Bus 001 Device 002: ID 09ae:0001 Tripp Lite Requires tripplite_usb driver as it is (Product ID: 0001). There is an entry in the compatibity list for OMNIVS800 USB (protocol 2012) using usbhid-ups which is little misleading (although I guess maybe correct for some instances of the UPS). OMNIVS1000 USB (older; product ID: 0001) is

This is a USB only ups. I could not make it work with nut. So I put this daemon together. Get it from http://www.vsys.org/sventura/dev/ at the bottom of the page. Init scripts are gentoo based but I think it should be easy to adjust them to any distro. I am planning to integrate it with nut if I can find the time and there is enough interest on it to justify the project. This is a very entry

I have a Tripp Lite OMNI900LCD. It has a usb connector and claims to be USB/HID. I haven't been able to get it to work with newusbhid or tripplite_usb. Here's lsusb -v output: Bus 001 Device 013: ID 09ae:2005 Tripp Lite Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 0 (Defined at Interface level)

I'm having problems creating a UPS connection to my Tripp Lite UPS System: Ubuntu 8.04.2 Nut 2.4.1 freshly compiled from source. When I do upsdrvctl start everything appears to work and I get :Detected a UPS: TRIPP LITE/TRIPP LITE UPS Using OMNIVS 2001 protocol (2001) Unit ID not retrieved (not available on all models) Attached to Tripp Lite UPS But

Hello All, This is my first post to the list & I have tried to do as much searching and debugging on my own as I can bear. Please HELP! I am currently using up to date Centos 5.2 32-bit - kernel version: 2.6.18-92.1.10.el5PAE #1 SMP. I am using a Tripplite OMNIVS1500 via usb connection. I am using the tripplite_usb driver. I have tried to user versions 2.2.0 from an rpm, 2.2.2 & and the