similar to: Communications with UPS lost: No status from UPS

2013/12/6 Fabio Cecamore <ceca_89 at hotmail.com>: > Hi all, Hi > I've problem with the management of my AtlantisLand UPS, the UPS don't want > to wake up after the whiteout and I don't have any idea why.. Some (very old) units are known to have problems with small values for ondelay (hence the default 3 minutes value):

2013/12/9 Fabio Cecamore <ceca_89 at hotmail.com>: > and the UPS don't wake up after the whiteout.. 2013/12/6 Fabio Cecamore <ceca_89 at hotmail.com>: > desc = "AtlantisLand Host Power 851+" Is your UPS an 'Atlantis Land Host Power 851' or an 'Atlantis Land One Power 841+'? The first one should be using a slighty modified version of the

Thanks for your reply Hyouko, these are the actual not working parameters: driver.parameter.offdelay: 60 driver.parameter.ondelay: 5 ups.delay.shutdown: 60 ups.delay.start: 300 and the UPS don't wake up after the whiteout.. My UPS is not so old :( Il 09/12/2013 16.04, hyouko at gmail.com ha scritto: > 2013/12/6 Fabio Cecamore <ceca_89 at hotmail.com>: >> Hi all, > Hi

Hello again! Sorry for not being able to test this before. Ulisses, please apply the patch to fix typo in my e-mail address. I've compiled it against nut-2.6.5 about 10 hours ago. It was everything fine until now. I'm seeing CHRG but the ups led wasn't blinking at all. Vendor software was strangely showing charging also. I am assuming this is expected behavior. I've set the

Use the name from ups.conf in front of "@localhost". ?The re?sult is quite different ;) root at artu:~# upsc Elit at artu Init SSL without certificate database Error: Driver not connected > What if you try nutdrv_qx without specifying megatec? (It should > autodetect.) > ?Here is the result: ? root at artu:~# upsdrvctl start Network UPS Tools - UPS driver controller

Merry Christmas to you all and best wishes! I ran into exactly the same problem as described. OS: FreeBSD 9.0-Rel UPS: Eaton E-Series NV 600H NUT: from Ports, nut-2.6.5_1 driver: blazer_usb I am sure the problem is not permission-related as it occurs even when the driver runs as root. My tested recipe for USB permissions is: 1. run usbconfig to find where the device is connected. In my case:

Hey all, I ended up picking up the module listed in Subject line. I switched over my config but apparently not all going smoothly. My config is: [office] driver = powerpanel port = /dev/ttyS0 desc = "Office UPS" When I test the driver running power-panel as a test, I get: > [root at cornelius init.d]# powerpanel -a office -D -D -D -D >

Hi all, after a change of UPS (to Atlantis Host Power 851) I began to use the new driver blazer_usb and compared to old one (blazer used with serial connection) I noted more CPU use and errors in dmesg: [...] [256712.584370] usb 4-5: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33 rq 9 len 8 ret -110 [256789.640795] usb 4-5: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33 rq 9 len 8

Hi, I know it's been a topic many times here, but I've searched the archives, googled for days, and I simply don't believe, that there is still no solution to this. I'm using a PowerCom BNT-600AP ups with usb port. I've downloaded the latest version from svn, compiled it, and tried to use it: * megatec(_usb) - no luck, it did not find the UPS (I?ve read in this list, that

Hi all, I've problem with the management of my AtlantisLand UPS, the UPS don't want to wake up after the whiteout and I don't have any idea why.. This is the ups.conf: [ups] driver = blazer_usb subdriver = cypress vendorid = 0665 productid = 5161 port = auto desc = "AtlantisLand Host Power 851+" pollinterval = 10 offdelay = 60 this is the upsc result: battery.charge: 100

Hi list, on my previous (lenny or squeeze) machine, I had it up and running, but that machine and configs are gone - and on my new jessie machine (see device and config details below) I cannot start the driver: # /lib/nut/bestups -DDDDD -a Patriot_Pro_II_750 0.000000 debug level is '5' 0.000806 send_to_all: SETINFO device.type "ups" 0.000842 send_to_all:

[As posted as Ubuntu Question #184284 on Launchpad] Hi, I try to set up nut (2.4.3) on my Lucid (10.04.3 LTS) to make use of my old but very trusty UPS (Best Power Fortress 660 LI). Yes, this UPS is old (about 16 years), but with its third battery pack last week it is as good as new. It runs perfectly well with Windows XP, Vista and even Windows 7. But not so with Ubuntu and nut. After

Hello all, been 5 years since I posted on this list, glad to be back :) I have a number of X-power Tigra 1kVA online UPS units. From some knowledgeable folks working for the local distributor, I learnt that from inside this looked like a Best 610 ups unit. Before, I had this UPS hooked via serial to my Windows 2003 server. For monitoring, some winpilot/upspilot software was also provided.

On Mar 5, 2015, at 2:34 AM, Jakub <jakub.scepka at gmail.com> wrote: > Come on, it started to be interesting! Do you have one of these UPSes? If so, here was Dan's email about a branch to test: > If you still can't get it to work with nutdrv_atcl_usb, another > approach could be worth considering. > > Since this UPS seems to be supported by UPSmart2000I, it could

Hello! I'm trying to use nut with a Ippon Smart Winner 3000 UPS (http://shop.key.ru/photo/items/45535.jpg) which looks like a custom-labeled OEM model of the megatec branch. I tried both the megatec_usb and the blazer_usb drivers for it, with a obvious config section: [ippon] driver = blazer_usb port = auto vendorid = 06da productid = 0003 desc = "Ippon Smart Winner 3000" If I

On Thu, Jun 26, 2014 at 10:20 PM, Steve Ballantyne <steve.ballantyne at gmail.com> wrote: >> However, we don't have all of the 09AE/0001 protocols decoded in the >> tripplite_usb driver. > > I can try to help out on this front? :-) Definitely. >> > 9.783126 Unknown input voltage range: 0x02 >> > 9.783308 Unknown number of switchable

Hello Charles, Thanks for the feedback. I will try to answer some of these questions: > 09AE/0001 is essentially a USB-to-serial converter, and is not > compatible with usbhid-ups. (Theoretically, we could have a companion > driver that talks the same protocols over a real RS-232 port, but the > hardware I used to develop the tripplite_usb driver only has a USB > port.) Ah, that

Hi all, I have problem with UPS from PowerWalker model VFI 2000 RT LCD over USB (didn't try serial yet). UPS should work via HID driver but ups.status is not rendered properly. Specification of UPS says USB HID compatible. HID driver is the only one which talks with UPS as i try a few from /lib/nut. I use driver usbhid-ups (which communicate with ups), but subdriver resolving is

Hello to all list members, I'm trying to make my UPS work with nut-2.2.2 (using Debian Testing, but compiled from source code) for a week ago, with not success. It's a Unitek Alpha 1000Ps, and I supossed it would work with megatec_usb driver, as other Unitek models. It has an USB interface, and when I plug it into my system I've got this message: chopito:/home/jordi# dmesg | tail

Dino, Alexey, there are a number of users suffering issues with your Powercom devices. Could you (Dino, and Keven if possible) please have a look at the below one, from Angela, and check for a fix? I've scheduled to release 2.6.1 next week, and having that fixed is part of the list. 2011/5/16 Angela Williams <angierfw at gmail.com> > Hi All > > On Friday 13 May 2011 at