similar to: Plexus 800VA UPS on ReadyNAS Duo

Hi I Bought a cheap Plexus 800VA UPS from ebuyer : http://www.ebuyer.com/product/240319 to use with my Netgear ReadyNAS duo. Initial version of NUT was very old and NAS didn't detect it although in the NAS log it said "UPS Disconnected". Syslog did send the following : Jan 25 12:46:36 nas-27lfc kernel: usb 1-1: new low speed USB device using uhci_hcd and address 2 Jan 25 12:46:37

Hi to everyone! I'm posting here after digging around the nut-upsuser and nut-upsdev mailing list, hoping I didn't miss something important. I'm trying to make my ups working with nut: it's a Tecnoware ERA LCD 0.85 which uses the so-hated UPSilon 2000 software to connect via usb. Personally I checked and seems that this junk software only works from windows, I'm trying to

Hi to all and happy new year! I'm writing here as I'm trying to get nut supporting the UPS in the subject; I didn't check well before buying and nowI discovered this is kinda bad hardware (it doesn't have a valid USB id, it just reports 0000:0001 and linux support doesn't really work as they stated), but before changing it I wanted to try to find a solution to get it work with

Hi all, I've bought UPS FSP EP 850 because I have similar UPS, FSP EP 1000. It is working on my other server with with Fedora 14, kernel 2.6.35.14-106.fc14.x86_64 and installed nut-2.6.2-1. My new UPS is detected by kernel (see below lsusb output) and is partially detected by blazer_usb driver also. But it doesn't communicate with driver (see below blazer_usb output). I run all

Hello i need your help regarding the following issue : i have a hero touch ups from infosec. it is connected via USB to a raspberry pi 3. i?ve configure ups.conf file as below [HERO] driver = blazer_usb vendorid = 0665 productid = 5161 either with port = auto or port = /dev/hidraw0 or port = /dev/ttySo the connection never works i get the

@fsp Please forward to development, manufacturing and quality management department: Model EP1000(PPF6000/100), 431107300095, 4711140480534, Art-Nr. 8296861, 70539, 14Z00000, 35-0200116-01G @nut-users http://www.networkupstools.org/ 2.4.3 debian stable, 2.6.2 upstream, linux 2.6.38-debian-bpo # /usr/local/src/nut-2.6.2/drivers/blazer_usb -u root -DDDDD -a ups Network UPS Tools - Megatec/Q1

No progress has been made: cable is UPS - PC 6 - 3 7 - 5 9 - 2 for ./blazer_ser -DDDDD -a infosec 0.000000 send_to_all: SETINFO driver.parameter.port "/dev/ttyS1" 0.000323 debug level is '5' 0.103068 send_to_all: SETINFO device.type "ups" 0.103104 send_to_all: SETINFO driver.version "2.7.3" 0.103118 send_to_all: SETINFO

Hello! I can't get my UPS to get detected. I have tried to search the internet for several hours. I have a Mustek Powermust 1400 USB that has both a USB and serial port. OS: openSUSE 20151209 (x86_64) VERSION = 20151209 CODENAME = Tumbleweed Kernel: 4.2.1-1-desktop Nut: nut-2.7.3-1.5.x86_64 installed with zypper dmesg |grep usb [94414.680765] usb 1-1.1: new low-speed USB device number 4

Hello All, I tested our new UPS yesterday. I noticed that while the blazer_ups drivers support this device, the newer nutdrv_qx does not. I suppose that this should not be the case, as nutdrv_qx will replace blazer_ups(?). Versions: I installed Nut on Ubuntu 13.10 (64 bit) from the standard package (2.6.4-2.3ubuntu2), and I also installed from the source tarball (2.7.1), into a different

Hi, I have a bunch of UPSs, most connected to pcs with Linux working 100% with NUT. The only one I have a problem with, is connected to Windows 7 64bit, and I used the straight MSI installed from the website named NUT-Installer-2.6.5-4.msi Took me a while to find a way to get it to work, but it is ugly for now. Just starting up the service results in a NUT not working at all, and I tracked it

Hi all, can anybody sugggest a proper solution to the problem described here: http://nut-upsuser.alioth.debian.narkive.com/wIMnftV0/installing-nut-for- powerwalker-vi-1500-lcd Righet now I am trying to make it go and running on version: root at raspberrypi:/home/pi/deb# apt-cache policy nut nut: Installed: 2.7.2-4 Candidate: 2.7.2-4 Version table: *** 2.7.2-4 0 500

System: Cenots Linux 6.9 Application: nut-2.7.5-0.20170613gitb1314c6 [with usb 0.1 from distro] Device: Mustek PowerMust 1060 LCD Comunication log file: dump.txt We are looking at the possibility of successful communicating with this device UPS Mustek PowerMust 1060 LCD. PS: wolfy on the list gives me assistance and i can install any new compiled nut version from sources. Thanks, Catalin.

Hello guys, Please help me to resolve the issue. I bought 'SVEN Power Pro+ 500 USB' UPS few days ago and tried to setup NUT 2.6.0 to work with it. blazer_ups driver doesn't recognize the UPS :( The Manufacturer provides 'PowerD' software for linux with installation instractions on a CD (see example below). --------===------- Welcom to PowerManager System!

Hi all, just landed here so apologize. I've googled a lot but I can't find a way to get my UPS working with NUT. here my ( relevant ) details: lsusb ... ... Bus 001 Device 027: ID 0001:0000 Fry's Electronics ... ... lsusb -v -d 0001:0000 Bus 001 Device 027: ID 0001:0000 Fry's Electronics Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB

Hello. I recently upgraded from Ubuntu Maverick to Natty and hence upgraded nut from 2.4.3-1ubuntu5 to 2.6.0-1ubuntu3. My Sven PowerPro+ 1000 UPS ( http://en.sven.ru/catalog/ups/power_pro_plus_1000.htm ) worked fine with the previous version, using megatec_usb driver, but doesn't work with the current version, since megatec_usb is no longer available. Here is the output from blazer_usb.

It seems like it works (partially?) with NUT/driver you mentioned. I will test it more when I return home. root at Failure:/lib/nut# ./nutdrv_qx -a test -x subdriver=fuji -u root -x productid=0000 -x vendorid=0001 -DDDDDD Network UPS Tools - Generic Q* USB/Serial driver 0.13 (2.7.2.5) USB communication driver 0.32 0.000000 debug level is '6' 0.001247 upsdrv_initups...

On 10/30/2017 03:19 PM, Alexa Catalin wrote: > System: Cenots Linux 6.9 > Application: nut-2.7.5-0.20170613gitb1314c6? [with usb 0.1 from distro] > Device:??Mustek PowerMust 1060 LCD > Comunication log file: dump.txt > > We are looking at the possibility of successful communicating with > this device UPS?Mustek PowerMust 1060 LCD. > > PS: wolfy on the list gives me

> We need to make sure this isn't something vm-related I suspect that this is definitely vm related now. I've tried Ubuntu server 10.10 as you suggested, and also Debian wheezy and both do the same thing. I saw in another thread that the author of the .vib of nut for ESXi is on this mailer - hopefully he can shed some light on what's happening. I would even be happy if I can

Hello, I am new to UPS stuff, please be patient with me ;-) Archlinux i686, kernel 3.0-ARCH #1 SMP PREEMPT. nut 2.6.1 installed from source via Arch's AUR repository. Mother board GA D525TUD with two serial ports, both enabled in BIOS. I got some old Orvaldi 520 PL UPS [1], which is supposed to be supported by the vendor [2] with sw called UPSmart. The statically compiled i386 binary ran

Hi all! Maybe possible adds something in megatec_usb driver for normal working with ippon 2000? This is output for drivers megatec_usb and blazer_usb: =========================================================== gate# /usr/local/libexec/nut/megatec_usb -DDDD -a IPPON Network UPS Tools - Megatec protocol driver 1.6 (2.4.1) Serial-over-USB transport layer 0.10 debug level is '4' Checking