similar to: ext-local and from-did-direct-ivr, how to change them?

Hi All; If I set a context other than the default context, then I do not see a generation for a configuration in the extensions_additional.conf for this context, but always the generation for the configuration is for the default context (from-internal). Normally, I have to put some Phones in a context and another Phones in a context, and give each context a privilages, but if I do this, then I

Hi Daniel, Am 27.03.20 um 09:24 schrieb Administrator: > Hangup is h extension. your macro will never be executed. Solution: > > same = n,Dial(whatever) > same = n,[...]) > same = n,Hangup > > exten  = h,1,1,DumpChan() >  same = n,System(/home/asterisk/bash_test) I don't really understand your code… I think I don't have to edit the first part of the conf file

Hello: We have a TDM2433E Digium Card (12 FXS, 12 FXO) and Asterisk 1.8.7.0 running. Everything seems to be ok but call transfers. This is the issue: *A, B, C and D are in FXS ports*. 1) A calls B. B anwers. 2) B tries to transfer the call to C dialing *2 (code for attended transfer). 3) A hears MOH. B dials number C. 4) Asterisk says the dialed number is incorrect or non existing. We tried

Hello- I have a low traffic AAH setup, a few hardphones, a few softphones, 50 calls per day max. I used the AMP Digital Receptionist to make a simple voice menu: "Thank you for calling xxxx". I did this for both Normal times and After Hours times. It worked fine. I then went to the AMP Maintenance window, Config Edit, got the "phpconfig for Asterisk PBX" page, and selected

Folks, First off, this is messy, and I hope someone will be kind enough to help me clean this up (the part added to extensions_additional.conf). You've been warned! For those of your using AMP or A@H, there has been a lot of talk about how to route incoming calls to different places based on which trunk is ringing. The standard answer is that you can only do this by using DIDs,

Hi All After lots of try I was successfull in connecting to PSTN to make and recevice calls , I used AMP for this purpose , now I wanted to try out this Asterisk server answers the call , ask for the extensions and then after the extension entered the call is forwarded /transfered to the extension no , I use Asterisk 1.2.4, configured using AMP , on RHEL3 I did some configuration for my

do you have selinux enabled? It should not be. p p.s. - if it comes to re-installing, you can backup all your settings with the freepbx backup utility and then restore so that you don't have to re-enter everything. From: "Lachek Butalek" <lachek@gmail.com> To: "Asterisk Users Mailing List - Non-Commercial Discussion" <asterisk-users@lists.digium.com> Date:

Figuring I knew what I was doing (I didn't - surprise) I added a totally unnecessary line in /etc/asterisk/extensions_additional.conf a couple of days ago. Troubleshooting a dialing rule issue, I'm now realizing that FreePBX is updating its database with the new settings but is not rewriting/updating extensions_additional.conf with the changes I'm making. I've tried renaming the

Greetings *`s, I am having what appears to be a small problem, but the frustration is erally getting to me, what am I doing wrong here ? I used AMP to set up a custom menu, so if caller presses 1 it goes to ext200, if caller presses 2 it goes to ext201 etc etc... Now I have created a third option that when the caller presses 3 it must play a sound and hang up. No rocket science yet. When

Hi All; When the call coming via the E1 dahdi and I handle the call (as first step) by exten => 5631040,1,Goto(OrangeCMG,s,1) it is not working and the call will be disconnected instead of queued. But, when I handle the call (as first step) by playing any sound file and then send for the queue, then it is working fine, WHY? exten => 5631040,1,Playback(WelcomeMessage) exten =>

Hi All; Again, the Cisco IP Phones 7942G and using Skinny: I upgraded the firmware to version 8.5 (skinny) and I am using skinny channel (chan_skinny) and the skinny.conf file. The phones are registering, but when we use them to place a call, we only hear tooooooooooo in the handset and we do not hear voice (even when we dial the digits, we only hear toooooooo .. but it dials and destination

Hi everybody, we use Asterisk to route all calls to a inbound phone number to a specific outbund mobile phone number, depending on time and date. I'd like to send a notification email to a specific email address, each time we receive a call. For this I used the tip of "dicko" here [1]. I'm a Asterisk newbie. Unfortunately it doesn't work. The System() command is not

Hi All; Can anyone advise if using Cisco IP Phones in skinny protocol is fine or not? Or it is better to use it in SIP protocol? Regards Bilal

Dear Tariq; About elastix.org, this can be use with Asterisk or it is coming as a complete IP Telephony, Call Center, IVR and Reporting? Because, I do not need to install another IP Telephony on the server which already has asterisk which is an IP Telephony, this will cause a problem in the service (for example, when listening for SIP port of 5060).

Hi, I'm struggling to get busydetect to work. I'm using asterisk 1.2.1 and a digium TDM04B (4 port FXO) card. I've set busydetect=yes, busycount=6 and busypattern=300,200 in zapata.conf and i've modified zondata.c with a busy setting of 620+480, 300/200 which is the busysignal received from Korea Telecom. Asterisk isn't detecting the busy signal and doesn't hangup.

Hello; Can someone advise me what is the maximum number of users (IP Phones) that can be supported by asterisk 1.8 or later? Regards Bilal -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.digium.com/pipermail/asterisk-users/attachments/20131218/7fbbc3c8/attachment.html>

I know almost nothing linux, and don't really know that much about Asterisk (proper).. but I was 'pulled' by this subject and grabbed an <mailto:Asterisk@home> Asterisk@home installation CD (version 1.3) and just went with it. Newbie doesn't quite describe it, I'm a banker.. this simply goes to show how easy Asterisk is becoming (I certainly hope this direction was meant

Hi All; I installed Asterisk on a new Server, it is a Dell Server and has 4 Ethernet ports. I gave IP address 192.168.0.3 for one Ethernet port. I am able to login for asterisk using /usr/sbin/asterisk -rvvv and from there (in the command line) I can type a commands. I have an Polycom IP Phone that is able to register for other Asterisk boxes (and some of them is 1.8.3) but with this new

Hi List; Where I can download Asterisk GUI and what I can have benifit from it? Regards Bilal ____________________________________________________________________________________ Be a better Globetrotter. Get better travel answers from someone who knows. Yahoo! Answers - Check it out. http://answers.yahoo.com/dir/?link=list&sid=396545469

Ok so I added to my Freepbx config running Asterisk 1.2.4 in extensions_custom.conf ; intercom exten => _7XXX,1,SIPAddHeader(Alert-Info: Auto Answer) exten => _7XXX,2,Dial(SIP/${EXTEN:1},12,Tt) and configured my Polycoms via this page http://www.voip-info.org/wiki/view/Polycom+auto-answer+config for auto answer and that works fine if I dial 7 then the 3 digit extension. No