similar to: Dell E6410

I bought a laptop with no PCMCIA slot, just expresscard. Instead of using a usb dongle for wireless, I would like to use an expresscard if possible. Ubiquiti makes one that uses atheros chip. Has anyone successfully used an expresscard wifi card in FreeBSD? Any info? Thanks

I'm looking for a well-supported ExpressCard or PCMCIA/CardBus SCSI card that can do at least FastSCSI (Narrow, Wide not necessary) that is supported by CentOS 7. I have an Adaptec SlimSCSI 1460D, but it doesn't seem to be supported (it's previously supported by the aha152x driver). Any ideas are welcomed, other than 'just use a desktop.' I am not sure a USB or Firewire

Ok, got a quickie. I have an eSATA drive, a 750GB Seagate in an eSATA external enclosure, and a Silicon Image sil3132 ExpressCard controller for my laptop. The disk and controller work great in CentOS 5 (or F7, for that matter), if I specifically mount it. This is not how I want to have to use this drive, however. I want to hotplug it; that is, plug the controller into the laptop, and then

2013/8/6 Gene Cumm <gene.cumm at gmail.com> > On Mon, Aug 5, 2013 at 9:04 AM, Jonas Keidel <jonas at jonas-keidel.de> > wrote: > > 2013/8/5 H. Peter Anvin <hpa at zytor.com> > > > >> On 08/05/2013 05:37 AM, Jonas Keidel wrote: > >> > I have problems with the current syslinux (6.02-pre16) booting CentOS > 6.4 > >> > 64bit via

I'm posting as an FYI. I was testing BIOS A04 with a UFD (USB Flash Drive) but it probably applies to everything that looks like a USB hard drive. My previous statement was partially incorrect as I did find a scenario to the contrary. I tried with FDD then CD at the top of the list and tried with both just disabled (without reordering first). I tried with the SATA controller in ATA, AHCI

On 11/12/2013 06:52 PM, Bob Doolittle wrote: > For the record - I figured this out so am sharing the result for > posterity: > > The issue was that I didn't follow the instructions literally. Since, > once booted, my primary NIC name was "em1" I assumed I had to create > an initscript called ifcfg-em1 rather than ifcfg-eth0 as described in > the doc. But you

Starting with the drm merge af3c8d98508d37541d4bf57f13a984a7f73a328c for 4.13-rc1, the NVidia NVS3100M display on Dell Latitude E6410 had a nullptr crash on startup. As a result later the suspend2ram was locking up. Traced to a null ptr in nv50_mstm_service(), which seems to be called only from nouveau_connector_hotplug(). Fixed by checking if mstm is not NULL before calling the service

Hi, Just browsing through the asterisk.org site and I see in the setup isntructions that only Zaptel, Libpri and Asterisk need to be checked out.. Has Zapata been intergrated into one of the other packages? -- ______________________________________________ http://www.linuxmail.org/ Now with e-mail forwarding for only US$5.95/yr Powered by Outblaze

Hi there, ? As suggested on the samba wiki, I like to report failures using samba4. ? Story: I had setup a general Office environment using samba4 (2 servers) with AD intergrated DNS (samba internal), Zarafa mail server (Prof.), ISC dhcp with split-scope and file shares (users, profiles, data and application) for a test-case environment.? Plan was to deploy this setup for a customer? (small 25

Hi, I'm trying to set up Asterisk behind my WRT54GP2 router that has a intergrated ATA box. My box are not locked in any way so I can access and change all settings. Now to the problem... I have gotten Asterisk to register with my provider and everything works just well.. Now it's time to get the intergrated ATA to connect to asterisk. But the asterisk box in located on the LAN ports of

Dear All, I bought one IP PHONE from Integrated Networks which was showed to wiki too: http://www.voip-info.org/tiki-index.php?page=Intergrated-Networks I have problems with the Asterisk authentication. It does't want to LOG IN to Asterisk; it always says "LOG ON FAILED". I'm using the IAX2 protocol and all paramters seems to be correct. Does somebody use the same IP PHONE with

Well i want to make a photography community site on the lines of www.gfxartist.com , www.terminus1525.ca, www.phirebrush.com Where the community votes for every subbmission from a artist and can comment (like a forum).. Now gfxartist has used probably SMARTY,php,and their own CMS. terminus used Drupal,Gallery 2.Some one tells me that this combo is heavy on resources and slows down sites.

I did installation of CentOS5.5 in text mode and made changes at the following places in the file /etc/X11/xorg.conf : section "device" identifier : "vesa" driver:"vesa" section "screen" device:"vesa" Also in the file /etc/inittab I changed id:3:initdefault to id:5:initdefault so that I can boot linux in graphical mode. I had to make the changes

Hi all, I have installed samba server and pritners. Instead having to put drivers to all clients, I decided to use the print$ share, so that, as I read, I can also make use of printing accounting. I did all the requird steps to install the pritner on my FC4 system, put all the required driver files to the print$ share, added the driver files to samba (npcclient adddriver) , verified samba can

2013/8/5 H. Peter Anvin <hpa at zytor.com> > On 08/05/2013 05:37 AM, Jonas Keidel wrote: > > I have problems with the current syslinux (6.02-pre16) booting CentOS 6.4 > > 64bit via LOCALBOOT 0 with the Intel DX79TO. > > Did it work in previous versions? > As i have written, in every previous syslinux version it didn't work. > > Also in every previous

Just wanted to get some thoughts from the list..... We are a public k-12 school and are looking to migrate to a groupware style system for out staff to collaborate better. Currently we are using Squirrelmail/postfix for email. Does anyone have any recommendations/opinions. Any input would be greatly appreciated. Thank you -- Bo Lynch Systems Administrator RedHat Academy Instructor Energy Manager

Hello all, I am thinking about a new laptop. I see that there are a number of higher-performance models (incidenatlly, they are also marketed as "gamer" ones) which offer two SATA 2.5" bays and an SD flash card slot. Vendors usually position the two-HDD bay part as either "get lots of capacity with RAID0 over two HDDs, or get some capacity and some performance by mixing one

I believe that you it did not understand my explanation. I have a Linux server executing samba intergrated with a server windows 2003 (PDC). Linux is using the users of windows 2003 saw winbind. But, the permissions for these of archive do not function. When I try to change the permissions of an archive in the sharing of the samba, it I do not function. The part of ACL of the samba is not

This is kind of a new area for me so I thought I would get the lists opinion. I have a avi video that I need to edit. The main thing that I need to accomplish is to maybe cut the top 1/3 of the frame and blur out a few faces. What would you guys recommend for an app that would accomplish this? Thanks in advance for any info. -- Bo Lynch

Hi All, I am doing some research on the intergration of Jabber and Asterisk. I have tried Jabber Client Mode. It's cool and works fine. But there's few information on the Component Mode. What's the difference between these two mode? I finished the configuration on jabber.conf and I am using openfire. What shall I do in the openfire to make them intergrated? Looks forward to your