similar to: mge-xml.c voltage conversion problem

Hi, This might be a simple thing to fix, but I can?t figure it out. We replaced the battery for the first time in our Eaton 5PX a couple of weeks ago, but we haven?t been able to clear the ?ups.alarm: replace battery!? status. Details of our installation are: OS: Debian 6 NUT version: 2.7.4 Installation method: from source tarball UPS device: Eaton 5PX2000IRT, 240V, 1800W, 2000VA, bought in

Dear folks, According to mge-mib.c (NUT 2.6.2) LB condition is gained from variable .1.3.6.1.4.1.705.1.5.14.0 (i.e. upsmgBatteryLowBattery.0). The test device of me does not set this variable to yes(1) even if runtime drops below the preconfigured limit. I complained about this at Schneider Electric. They replied that low battery status is indicated by .1.3.6.1.4.1.705.1.5.14.0

Hi, I have a HP R1500 G2 UPS and want to get it working under Debian Lenny - as this OS is not supported by HP I'm trying to use nut for it - but I can't get it working. Do I have any chance to get the UPS running with nut. I also tried different drivers but had no luck either. Or does anyone has experience with HP UPS under debian ? Any help would be nice ! I tried /lib/nut/usbhid-ups

Charles, It starts out good, then goes into a Connection timed out loop. If I can provide any information to fix a driver I'll do my best. Here's the output: # /usr/local/ups/bin/usbhid-ups -DD -a eaton Network UPS Tools - Generic HID driver 0.41 (2.7.4) USB communication driver 0.33 0.000000 debug level is '2' 0.002550 upsdrv_initups... 0.288229 Checking device

Hi I would like to be able to use this UPS with NUT please ? Product id = 53962KX Network UPS Tools - Generic HID driver 0.38 (2.7.2) USB communication driver 0.32 0.000000 debug level is '2' 0.002761 upsdrv_initups... 0.014996 Checking device (03F0/0024) (001/005) 0.032670 - VendorID: 03f0 0.032790 - ProductID: 0024 0.032955 - Manufacturer:

Hi there, OS: (L)ubuntu 12.04 precise LTS Nut: 2.6.3-1ubuntu1.1 Installation Method: Package (apt-get install nut) Hardware: HP R1500 G3 INT Hardware-Specs: http://h18004.www1.hp.com/products/quickspecs/14059_div/14059_div.pdf Problem: I tried to set up nut with our new arrived HP R1500 G3 UPS but there is a failure with the usb connection. After trying "/lib/nut/usbhid-ups -DD -a

Hello, I've recently bought Ippon Smart Winner 3000 New (note the "New" in the model name) and I can't make NUT to work with it. Linux gateway 3.17.8-gentoo-r1 #1 SMP Mon Feb 16 13:46:11 MSK 2015 x86_64 Intel(R) Celeron(R) CPU 1037U @ 1.80GHz GenuineIntel GNU/Linux Network UPS Tools 2.7.2 1) USB connection partially works using usbhid-ups driver, the problem is that I

Have recently purchased a MGE Nova 1100 UPS and am trying to get running on netBSD. Configuration netBSD 3.0 amd64 libusb 0.1.10a nut 2.0.3 Built & installed libusb Built kernel with ugen device and uhid removed Build & install nut-2.0.3 with usb Chmod /dev/ugen1 etc to allow access by nut user. Ups.conf [MGENova] driver = newhidups port = auto

Greetings everyone, Firstly, sorry for the huge length of this message. The support page said send debug traces, and so debug traces shall be sent. OS name and version - Arch Linux - updated today. exact NUT version - 2.7.4 (Network UPS Tools - Generic HID driver 0.41 (2.7.4) USB communication driver 0.33) NUT installation method - Arch User Repository build script updated to use latest NUT

Hi, I've been using NUT for many years to look after the UPS on my home servers. Originally I was using a Compaq R3000 but that was replaced with an MGE Pulsar Evolution 3000 about a couple of years ago because the Compaq one was just too noisy! I'm just setting up a replacement server and would like to connect it using a serial cable as I've found that the USB connection

To all, I attempted to configure the UPS tools for the Tripp-Lite SmartOnline 1500VA 2U rackmount UPS. I followed the instructions from the 'upsdrvctl start' output and posted the diagnostic information below. Is my UPS using an unknown product ID as reported? From the mailing list archive, I have found another posting for the same UPS with device model '09AE/4003', whereas

It's been a while since I tried to use NUT, so I thought I would give it another try. Big trouble. The UPS is a Tripp-Lite AVR 550U. It has only a USB connector. The computer is running Red Hat Enterprise Linux 4. I just installed NUT version 2.2.0. I'm going through the steps in the INSTALL document. # cat ups.conf [igor] driver = usbhid-ups port = auto

Does the following error message have a specific meaning: usb 1-1: usbfs: USBDEVFS_CONTROL failed cmd usbhid-ups rqt 161 rq 1 len 2 ret -75 I get two of these messages every time I run the following: /lib/nut/usbhid-ups -u root -DDD -a trippy The following is the output from the above command: debug level is '3' Checking device (0000/0000) (004/001) - VendorID: 0000 - ProductID:

When running 'sudo upsmon -c fsd' UPS turns off then back on after a delay as expected. But when power is disconnected and the command is ran, the UPS turns off but still turns back on again. Changing 'ondelay' to -1 or 0 does not change the behavior. How can I get the UPS load to stay turned off if there is no power? Or am I misunderstanding how to test this functionality?

I suspect that the battery is failing on my Pulsar Evolution 500 (it is several years old now) but I can't seem to get a valid battery voltage from the UPS. The following tests were done using NUT 2.2.1, but I first noticed this with the trunk, and reproduced it with the current branches/Testing as well. The only two values I have seen for battery.voltage are 120.0 and 119.0, e.g.: $ upsc

My UPS is connected to a Raspberry Pi by USB. After a few hours of working, the service fails. Looking at kernel messages I noticed that the device is repeatedly disconnecting and reconnecting. I have tried using a different USB port and using a brand new USB cable. I have not had success by changing config parameters like pollfreq/pollinterval/etc. What is causing the UPS to keep disconnecting?

I?m setting up a new system and installed a new UPS with nut. System Specifics: OS: Debian 3.16.36 Nut version: 2.7.2 Install method: apt-get Device: TRIPPLITE SMART1300LCDT using usbhid-ups driver Problem: The output from upsc has a few incorrect values. They appear to be a matter of scale. root at server:/etc/nut# upsc tripplite at localhost Init SSL without certificate database

Hello, I am having difficulty using NUT to shut down my Netgate SG-1100 (a pfSense router) when the power level of the UPS gets critically low. Here is some relevant information: - OS: pfSense 2.4.5-RELEASE-p1 (FreeBSD 11.3-STABLE) - NUT version: 2.7.4 - Installed from: pfSense package 2.7.4_7 - UPS: AVR750U (Device release number 2) - I have included my config files, output from `upsc`, and

*********************** Your mail has been scanned by InterScan MSS. *********************** Has anyone managed to get this UPS to work? I am using the laster development nuts. My /proc/bus/usb/devices content: ==== cut ==== T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=1.5 MxCh= 0 D: Ver= 1.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=ffff ProdID=0000 Rev= 1.00 S:

Hello, I am hoping someone can point me in the right direction. I am setting up a new UPS, most things seem to be working except the UPS turns off immediately during a test shutdown using///"//upsmon -c fsd".//No delay before the UPS turns itself off leaving no time for the server to shutdown properly. I have attempted to set the delay higher using "upsrw -s