similar to: Liebert GXT2 Support

Good morning, I just had the chance this morning to get my linux box tied into our network and talking to the UPS. I can now confirm that in NUT v2.4.3 snmp-ups (ietf) works with the Liebert Intellislot Web Card for the GXT2 family of UPS'. upsc output: tux ~ # upsc workups at localhost battery.charge: 100.00 battery.runtime: 2760.00 battery.runtime.low: 5 battery.voltage: 54.60 device.mfr:

Good morning, I just had the chance this morning to get my linux box tied into our network and talking to the UPS. I can now confirm that in NUT v2.4.3 snmp-ups (ietf) works with the Liebert Intellislot Web Card for the GXT2 family of UPS'. upsc output: tux ~ # upsc workups at localhost battery.charge: 100.00 battery.runtime: 2760.00 battery.runtime.low: 5 battery.voltage: 54.60 device.mfr:

Hi guys, I wrote for Arnaud that I tested the liebertgxt2 driver in 2.4.3. I compare output of Richard's code, Spiros code and nut 2.4.3. Output of Richard and Spiros codes was same and right. Output of Liebertgxt2 driver isn't. Examples: Our UPS : Liebert GXT2-1000RT230 Model Name,Firmware version,SN,date of manufactured values was right. Fields

Hi All, Attached is a patch against nut-2.4.1 that adds a driver for the ESP2 protocol, as used by the serial port found on the Liebert GXT2. This driver is mostly based on: http://www.csc.liv.ac.uk/~greg/projects/liebertserial with additional bit field information from Spiros Ioannou. liebert.c at the above url has been tested by a few people to return the correct status data. Besides me,

I am working with three Liebert GXT2 UPSes connected via local TCP/IP under Linux 2.6.25.1 and getting a series of messages. First, at start, the drivers complains that the Liebert apparently extract information from certain MIBs in the ietf MIB file.... Network UPS Tools - UPS driver controller 2.2.2 Network UPS Tools - Multi-MIBS SNMP UPS driver 0.421 (2.2.2) Warning: This is an experimental

Is this the best place to get into contact with the snmp-ups driver developers? I am trying to get the snmp-ups driver to work with a Liebert GXT2 UPS, and it works for knowing when it goes on battery and such, but when it comes to shutting down the Liebert UPS, it doesn't work. Any suggestions or docs that I need to read? -- Ronald Reed Manager of Computer Operations ARM SGP ACRF Site

based on r2432, i took this with "svn diff --revision HEAD liebert-esp2.c" fixes: 1) new way to initialize model, firmware etc. variables, the strok way failed because some vars had spaces. (e.g. model "Liebert NX") 2) new multipliers for: frequency, nominal power. I get correct readings now, before I had 500 Hz, and 200VA and now it's ok for me. Test with your models. 3)

hello in first sorry for my poor english i've got a new ups "leibert GXT2-6000RT230" and i would like to use nut to make shutdown some server plugged on it. I bought a card with this ups "opencomms web card". I dont know where to plug the serial cable, directly on the serial port on the ups or on the serial port on the opencomms card, and with wich cable. I've got a

hi, we working together with robert to make liebert ups with nut. there was a good revision 2431 which gives a good result for us. this revision call the driver gxt2. after that you change the name to esp2. unfortunately this version (and the current head too) contains the same bug what was previously fixed in the gxt2 branch. it'd be useful to port the fixes to the new esp2 branch too. the

2009/10/19 Jobbagy Robert > |Hi Arnaud! Hi Robert, > I'm a hungarian developer and I need make a linux driver for this ups: > "Liebert" ? ? ? "ups" ? "5" ? ? "UPStation GXT2" ? ? ? ?"contact-closure > cable" "liebert" (I copied it from your previous mail) > So please help me,where should I start it ? > > |Thank

Hi, I have a Liebert GXT2-1000RT230 UPS that is connected to my server using a serial cable. I have no idea to what port exactly it is connected so my first question is: how do I find out what /dev/tty** should I use? Do I need to install a device driver for it? Where do I find it? What should I use and how do I do so the server shuts down if the battery level is low? Yes, I'm a newby,

2009/1/22 Spiros Ioannou <sivann at gmail.com> > Cher Arnaud, > Hi Spiros, > I send you a demo that reads info from an Emerson Liebert > GXT2-10000T230 through the RS-232 port. This uses the "ESP-II (ESP 2) > Protocol". > Current supported data includes: measurements (voltage, temperature, > etc) , ID strings (serial number, etc), status flags (inverter on,

Afternoon, I've got an old Dell PERC 4DC (PCI 64bit/33MHz) sitting in my home rig and with a new board on the way that has PCI-X (133) and PCIe (x4) slots, I was wondering what people would recommend for a cheap hardware parallel SCSI RAID controller (no fake raid please) that is relatively cheap but faster then the old PERC? I'm looking for something cheap that'll do RAID-10 but

Hi all, I?ve a UPS Liebert GXT3 500-3000VA with USB port. I?ve install NUT version 2.2.2 from repository packages for Debian Lenny. Linux kernel 2.6.26 I?ve try to use usbhid-ups driver in ups.conf [liebert] driver=usbhid-ups port=/dev/usb/hiddev0 Debian get the usb: # lsusb -v Bus 001 Device 002: ID 10af:0008 Liebert Corp. PowerSure Interactive UPS Device Descriptor: bLength

On a semi-related subtopic, Why do I want WoL? What concrete examples are there where it's useful? I understand what it is and how it works but the "why" has eluded me. -- Drew "Nothing in life is to be feared. It is only to be understood." --Marie Curie

Hi guys, I found the troblue and fix it! I attached the patch. The trouble was in the command reply buffer use. You compute the value that value = reply[6]*256+reply[5] <- it's wrong The right solution: value = reply[5] * 256 + reply[6]; And other bug, battery.runtime compute, you divide this value 60 <- it's wrong right value: divide 1.0 I continue the work on this

Morning Everyone, I'm busy doing a rebuild of my home server and am tossing between VMware and KVM for this build. I already have experience with ESX, we use it at work, but I'm debating trying out KVM for a while. The server itself is a budget build using a Supermicro X8SAX board w/ i7-950 & 12GB RAM, LSI 3081 SAS RAID (1068e based), rolled into a NorcoTek 16 Bay SAS case. Not fancy

Morning Everyone, I'm busy doing a rebuild of my home server and am tossing between VMware and KVM for this build. I already have experience with ESX, we use it at work, but I'm debating trying out KVM for a while. The server itself is a budget build using a Supermicro X8SAX board w/ i7-950 & 12GB RAM, LSI 3081 SAS RAID (1068e based), rolled into a NorcoTek 16 Bay SAS case. Not fancy

I have a need to use NUTS on a Windows 2016 Server however as all the resources are Linux orientated I am having serious issues getting things to behave. We have a serial Port COM4 attached to a Liebert GXT2-3000RT230 using its dedicated cable. It worked fine when we could use JAVA and the windows 'Multilink' software which came with it. Only MSI I could find in download section -

Hello I'm trying to manage my liebert UPS with nut installed on a raspberry pi Installation of nut is OK but th? driver doesn t works Could y ou help me ? Best regards Jean-marie