similar to: BCMXCP UPS driver 0.24 (2.6.1) Hangs

Good evening, I tried getting this to work a couple years back but didn't have enough time to do all the debugging that was needed (apologies to the devs who tried to help at that time). It's working much better now, but I'm still not able to get an answer from upsc. Can anyone help me work out why I'm getting the error when querying with upsc: Error: Data stale My

Good evening, I tried getting this to work a couple years back but didn't have enough time to do all the debugging that was needed (apologies to the devs who tried to help at that time). It's working much better now, but I'm still not able to get an answer from upsc. Can anyone help me work out why I'm getting the error when querying with upsc: Error: Data stale My

Hello Charles, I think we are making progress! I grabbed nut using git, and applied your patch without any problems. Getting to the point that I could run a configure on my RPi - was something else. I found this blog post, which was very helpful (for anyone else that may try it): http://atelier-orchard.blogspot.com/2013/11/raspberry-pixf86-video-fbdev.html It's not in English, but you get

Hi, I have set up a RaspberryPi computer to do monitoring of two UPSs. One is an MGE evolution 800, one is an Eaton Powerware 5110. The MGE was being monitored by another Linux (Ubuntu 12.04) computer, and I just copied and pasted in the relevant nut config and it works just fine with nut. I've tried to set up the Powerware 5110 with nut, and the bcmxcp_usb driver can't communicate

Hi. I'm looking for a way to configure an Eaton Powerware 5125 under Debian Squeeze (amd64) with USB port. Can someone help me? Find attached bellow my settings: # cat /etc/nut/ups.conf ... [ups01] driver = bcmxcp_usb port = /dev/bus/usb/002/003 desc = "Powerware 5125" # ls -la /dev/bus/usb/002/003 crw-rw-r-- 1 root nut 189, 130 Nov 21 11:45 /dev/bus/usb/002/003 #

<nut-upsuser at lists.alioth.debian.org> I am doing my best to avoid have to spend $280 for a network monitoring card to put into a $190 UPS just to have some good remote monitoring capabilities. Rather, I would like to monitor my many 1U Tripp Lite's on my network using a Raspberry Pi running Raspian and using NUT. However, I cannot seem to get it working. And I while the hardware

Hi All, I have a powerware UPS 5110 connected to an openindiana server with the bcmxcp_usb driver and running nut 2.65 compiled and installed as root to avoid permission issues. On running the following debug code to test the UPS's communication it fails at the same time with the following error. ./bcmxcp_usb -u root -DDD -a 5110 ....... 2.523879 get_answer: (128 bytes)

Hi all, I just acquired a new UPS and have been trying to get it to work with NUT. It's an Eaton/Powerware 9120 700i with both USB and RS-232 interfaces. I first tried the USB interface (using bcmxcp_usb) and found that the UPS worked fine for a few minutes but then NUT lost communication and didn't get it back. In addition the UPS itself seemed to lock up at one point such that the

l?rdagen den 29 juni 2013 15.22.44 skrev Mike.: 8<-------------snip----------------- Sorry for the delay. > Here is the console output of bcmxcp with -DDD specified: > > > [snip] > 13.721204 Auto delay on: 2 > > 13.721243 send_command: (4 bytes) => ab 01 35 1f > 13.821127 send_command: (4 bytes) => ab 01 33 21 > 13.920982

Hi I Bought a cheap Plexus 800VA UPS from ebuyer : http://www.ebuyer.com/product/240319 to use with my Netgear ReadyNAS duo. Initial version of NUT was very old and NAS didn't detect it although in the NAS log it said "UPS Disconnected". Syslog did send the following : Jan 25 12:46:36 nas-27lfc kernel: usb 1-1: new low speed USB device using uhci_hcd and address 2 Jan 25 12:46:37

On 6/29/2013 at 6:16 PM Kjell Claesson wrote: |l??rdagen den 29 juni 2013 11.28.14 skrev Mike.: |8<------------------snip--------------------- |Hi Mike, |> |> Thanks for the quick reply. |> |> I checked the log file (which, admittedly, I should have done before I |> posted about the problem :) ). |> |> Here's the command and the corresponding log message: |>

Hello Charles, Thanks for the feedback. I will try to answer some of these questions: > 09AE/0001 is essentially a USB-to-serial converter, and is not > compatible with usbhid-ups. (Theoretically, we could have a companion > driver that talks the same protocols over a real RS-232 port, but the > hardware I used to develop the tripplite_usb driver only has a USB > port.) Ah, that

@fsp Please forward to development, manufacturing and quality management department: Model EP1000(PPF6000/100), 431107300095, 4711140480534, Art-Nr. 8296861, 70539, 14Z00000, 35-0200116-01G @nut-users http://www.networkupstools.org/ 2.4.3 debian stable, 2.6.2 upstream, linux 2.6.38-debian-bpo # /usr/local/src/nut-2.6.2/drivers/blazer_usb -u root -DDDDD -a ups Network UPS Tools - Megatec/Q1

hi! When I turn on my pc everything works fine, but if I restart fails (I'm not sure if this is true at 100%)?(then, i can do 'sudo /etc/init.d/nut restart' and it works) But what is certain is that sometimes when start up the pc it works and sometimes fails, can be a problem with the start time (i have a fast ssd) and the initialization of the driver and the usb port? thanks! syslog:

Hello guys, Please help me to resolve the issue. I bought 'SVEN Power Pro+ 500 USB' UPS few days ago and tried to setup NUT 2.6.0 to work with it. blazer_ups driver doesn't recognize the UPS :( The Manufacturer provides 'PowerD' software for linux with installation instractions on a CD (see example below). --------===------- Welcom to PowerManager System!

Hi all, I have problem with UPS from PowerWalker model VFI 2000 RT LCD over USB (didn't try serial yet). UPS should work via HID driver but ups.status is not rendered properly. Specification of UPS says USB HID compatible. HID driver is the only one which talks with UPS as i try a few from /lib/nut. I use driver usbhid-ups (which communicate with ups), but subdriver resolving is

cmd test.battery.start.deep was not tested yet. cmd test.battery.start.quick works as expected. cmd test.battery.start 120 works as expected. cmd test.battery.stop works as expected. cmd beeper.toggle works as expected. cmd shutdown.return works as expected. cmd shutdown.reboot does not work entirely. After a minute, UPS is shut down but didn't come back. (Issuing shutdown.stop power up it

Hey Charles, Many months ago you assisted me in making some code changes to get my Tripp Lite up and running. Thank you for that. Those changes you committed to the repository work very well. I just built a new image for a Raspberry Pi running the latest Raspbian OS and the latest nut-master. I have everything working ... except I seem to be losing my device periodically. So if I enable my

Dear friends, I installed NUT and followed all suggested procedures to verify if my ups is supported. No driver recognized my ups, and the genericups tests get wrong. Here I send some informations about it: The ups model is APC BZ1200-BR I use Ubuntu, and the lsusb results Bus 003 Device 003: ID 0403:6001 Future Technology Devices International, Ltd FT232 USB-Serial (UART) IC for ups. The

Hi Arnaud and NUT team You may recall some time ago, I and a few others posted questions about the above referenced (cheap and cheerful) USB-based UPS - specifically regarding FreeBSD USB support in NUT. The original posting was entitled "Zigor Ebro 650 compatibility". I've since tried the latest Windows port of NUT with my WinXP laptop connected to the Zigor Ebro and finally