similar to: TrippLite Eco Series UPS

Hi all, I have problem with UPS from PowerWalker model VFI 2000 RT LCD over USB (didn't try serial yet). UPS should work via HID driver but ups.status is not rendered properly. Specification of UPS says USB HID compatible. HID driver is the only one which talks with UPS as i try a few from /lib/nut. I use driver usbhid-ups (which communicate with ups), but subdriver resolving is

I am currently running FreeNAS-8.3.1-RELEASE-x64 (r13452) using the packaged version of NUT, 2.6.5, using the usbhid-ups (Generic HID driver 0.37). Here is the output of "/usr/local/libexec/nut/usbhid-ups -D -D -D -D -D -D -a tripplite": Network UPS Tools - Generic HID driver 0.37 (2.6.5) USB communication driver 0.31 0.000000 send_to_all: SETINFO driver.parameter.port

Hi, I'm running the latest version of NUT and with the above UPS and I keep getting the following error: "tripplite_usb[3308]: Error reading B value: Device detached? (error 0: could not claim interface 0: Device or resource busy)" The device keeps disconnecting and re-connecting until fails. I've tried to see if others are getting this - but I could not locate a

<nut-upsuser at lists.alioth.debian.org> I am doing my best to avoid have to spend $280 for a network monitoring card to put into a $190 UPS just to have some good remote monitoring capabilities. Rather, I would like to monitor my many 1U Tripp Lite's on my network using a Raspberry Pi running Raspian and using NUT. However, I cannot seem to get it working. And I while the hardware

Dear friends, I installed NUT and followed all suggested procedures to verify if my ups is supported. No driver recognized my ups, and the genericups tests get wrong. Here I send some informations about it: The ups model is APC BZ1200-BR I use Ubuntu, and the lsusb results Bus 003 Device 003: ID 0403:6001 Future Technology Devices International, Ltd FT232 USB-Serial (UART) IC for ups. The

Hello Charles, I think we are making progress! I grabbed nut using git, and applied your patch without any problems. Getting to the point that I could run a configure on my RPi - was something else. I found this blog post, which was very helpful (for anyone else that may try it): http://atelier-orchard.blogspot.com/2013/11/raspberry-pixf86-video-fbdev.html It's not in English, but you get

hi! When I turn on my pc everything works fine, but if I restart fails (I'm not sure if this is true at 100%)?(then, i can do 'sudo /etc/init.d/nut restart' and it works) But what is certain is that sometimes when start up the pc it works and sometimes fails, can be a problem with the start time (i have a fast ssd) and the initialization of the driver and the usb port? thanks! syslog:

Hi I Bought a cheap Plexus 800VA UPS from ebuyer : http://www.ebuyer.com/product/240319 to use with my Netgear ReadyNAS duo. Initial version of NUT was very old and NAS didn't detect it although in the NAS log it said "UPS Disconnected". Syslog did send the following : Jan 25 12:46:36 nas-27lfc kernel: usb 1-1: new low speed USB device using uhci_hcd and address 2 Jan 25 12:46:37

Hello, I have just installed nut_2.6.0 from Debian testing, do anyone know the correct driver for this ups? The blazer_usb don't report battery-charge, the bundled software report charge and runtime. root at pluto<~>upsc powerwalker battery.voltage: 40.86 battery.voltage.nominal: 36.0 beeper.status: enabled device.mfr: device.model: HV 1K device.type: ups driver.name: blazer_usb

> > hmm, apparently the UPS doesn't close the replies to our queries with > the expected CR and we (I) did not consider that case in nutdrv_qx -- > noted: > https://github.com/networkupstools/nut/issues/441 > > But blazer_usb, being less strict on the terminating CR of Q1 replies, > should work with your device. > > > root at artu:~# upsc Elit at artu > >

Hello, I have a UPS branded as "Energit MXE II" that comes with the infamous Winpower software (as already discussed in this old thread <http://nut-upsdev.alioth.debian.narkive.com/m0FWk43o/blazer-usb-compatibility-with-ippon-backpro-upses-phoenix-power-co-ltd-usb-to-serial-controller>). This same UPS appears to be sold as "Centralion Titan Elite" and maybe other names

It seems like it works (partially?) with NUT/driver you mentioned. I will test it more when I return home. root at Failure:/lib/nut# ./nutdrv_qx -a test -x subdriver=fuji -u root -x productid=0000 -x vendorid=0001 -DDDDDD Network UPS Tools - Generic Q* USB/Serial driver 0.13 (2.7.2.5) USB communication driver 0.32 0.000000 debug level is '6' 0.001247 upsdrv_initups...

@fsp Please forward to development, manufacturing and quality management department: Model EP1000(PPF6000/100), 431107300095, 4711140480534, Art-Nr. 8296861, 70539, 14Z00000, 35-0200116-01G @nut-users http://www.networkupstools.org/ 2.4.3 debian stable, 2.6.2 upstream, linux 2.6.38-debian-bpo # /usr/local/src/nut-2.6.2/drivers/blazer_usb -u root -DDDDD -a ups Network UPS Tools - Megatec/Q1

Hi all, I've bought UPS FSP EP 850 because I have similar UPS, FSP EP 1000. It is working on my other server with with Fedora 14, kernel 2.6.35.14-106.fc14.x86_64 and installed nut-2.6.2-1. My new UPS is detected by kernel (see below lsusb output) and is partially detected by blazer_usb driver also. But it doesn't communicate with driver (see below blazer_usb output). I run all

Hi to everyone! I'm posting here after digging around the nut-upsuser and nut-upsdev mailing list, hoping I didn't miss something important. I'm trying to make my ups working with nut: it's a Tecnoware ERA LCD 0.85 which uses the so-hated UPSilon 2000 software to connect via usb. Personally I checked and seems that this junk software only works from windows, I'm trying to

Howdy, I had this working with lots of help for a developer before (Charles Lepple), but after upgrading to a somewhat more current version of FreeBSD the patched-up version stopped working. Seeing as this was more than a few years ago, I thought I'd give a new libusb and NUT a try to see if it might work out of the box. So far, no luck. Some info: FreeBSD 6.3 libusb 0.1.12 NUT 2.4.1

Hi to all and happy new year! I'm writing here as I'm trying to get nut supporting the UPS in the subject; I didn't check well before buying and nowI discovered this is kinda bad hardware (it doesn't have a valid USB id, it just reports 0000:0001 and linux support doesn't really work as they stated), but before changing it I wanted to try to find a solution to get it work with

Hello There, I tried your advice and i don't think it works either, See the logs, " /tmp/nut# ./drivers/usbhid-ups -DDDDDD -d1 -s test -x port=auto -x vendorid=... -x productid=... -x subdriver=... Network UPS Tools - Generic HID driver 0.52 (2.8.0-2557-g81fca30b2) USB communication driver (libusb 1.0) 0.46 ?? 0.000000??? [D3] main_arg: var='port' val='auto' ??

<facepalm ;)> the ellispis "something=..." were supposed to be replaced by your device ID numbers, etc. On Sat, Sep 23, 2023, 18:26 FatGear <fatgear1 at free.fr> wrote: > Hello There, > > I tried your advice and i don't think it works either, > > See the logs, > > " > > /tmp/nut# ./drivers/usbhid-ups -DDDDDD -d1 -s test -x port=auto -x

Hi. My Belkin UPS F6C1100-UNV works fine with megatec_usb version 1.6 (2.4.1). However, it doesn't work with 2.4.2 nor 2.4.3. # /lib/nut/megatec_usb_old -D -a belkin Network UPS Tools - Megatec protocol driver 1.6 (2.4.1) Serial-over-USB transport layer 0.10 debug level is '1' Starting UPS detection process... 0 out of 5 detection attempts failed (minimum failures: 2). Cancelling