similar to: Ground Start ATA / VOIP Gateway

Callerid issue 1) if you run ztmonitor on the fxo line & call in do you hear the fsk tone if yes then we beleive the CAC is passing fsk 2) in chan_zap->ss_thread around line 4154 (current cvs) if you get to the callerid_feed at least once then if you get to chan_zap->ss_thread->callerid_get around line 4163 (current cvs) does this parse fail

Hello Astrites, I was just about to send out a long email about not being able to detect hang-up with my CAC II FXO module on my PSTN POTS lines. I had tried many configurations. I had attached a toner to the line to see if I was getting this "disconnect supervision" signal after hang-up. (toner has a line powered light in the off position) It seemed that I was getting the signal,

hello, I just installed 2 brand new x100p cards into my linux system. Everything compliled and worked fine from the first try. Hoewver the phone lines I will use with this system have groundstart signaling. I have tried to change the zaptel.conf and zapata.conf to use this type of signaling but ztcfg gives me an error every time with the new configuration. Bellow are the config files and the

I am having a problem using the Adtran 750 FXO quad card with a Groundstart trunk line. I am able to receive calls on the trunk line, however dialing out is not working. The Adtran does not seem to be doing the signaling. Has anyone used the 750 FXO card in Groundstart mode? Any special configuration issues that I should be aware of? Syed Akbar Alico Systems Inc www.alicosystems.com Tel:

I have the following upcoming install and I'm trying to do it without having to resort to Digium t1 cards. I have a Cisco IAD2431 being installed by our Carrier. That Carrier will be providing 2 IP Trunks via ethernet handoff into the Cisco IAD2431. The CIsco IAD2431 has Two T1 ports installed and we would have to install a digium card to support those two t1's. What I'd like to do

I've read the wiki and other resources on how to connect Vonage / Voicepulse and all these other services to Asterisk... We are attempting a connection to a Lucent iMerge. Lucent has told us that it won't work - but we feel confident that it will. Has anyone worked with the Lucent iMerge - or would be willing to help lend a hand? It is capable of H323 / MGCP. Even if I could make the

I have a problem where an Asterisk server is sending a premature DRQ... Not sure why.. Here's the setup - Asterisk using inAccess networks H323 replacement channel driver Connecting to a Lucent iMerge... The call connects fine - I get the out of the box greeting - but after exactly one Minute - the call terminates. I have had this problem on multiple different Asterisk configs... I'm

I have a Cisco 7940 when you call in from outside and dial the Cisco phone extension I get this Read_channel ## vpb/1-3: Setting record mode, bridge = 0 WARNING[18451]: File chan_sip.c, Line 1111 (sip_write): Asked to transmit frame type 8, while native formats is 4 (read/write = 4/4) == Spawn extension (default, 1004, 1) exited non-zero on 'vpb/1-3' -- hangup on vpb (vpb/1-3)

I bought an Aastra PT480 from digium, but I wanted to see if I could get some more help with this before Monday. Any help would be appreciated. I have the phone connected to the TDM400P card, and I also have the T100P and the X100P in the same box. My problem is, it appears as if the phone and asterisk can't understand each other. The port the phone is connected to always remains

Hi, I have a TrixBox install with a Sangoma A200 and 4 FXO ports, there are 3 BT lines connected directly to these ports. One of the lines has BT FeatureLine Compact and this is the line I am having problems with, the other 2 lines are working perfectly, detecting CID, answering incoming calls and placing external calls via SIP devices. I am receiving a error log entry: chan_zap.c:

Hi: I want to connect a wi-fi phone to my Asterisk box through a wi-fi AP so I can make voip calls. please send me your recomendation about what wi-fi phone I should be looking for. Anybody tried the HOP1502 Wi-Fi IP phone. Its listed price $39. Regards; Chawki ____________________________________________________ Yahoo! Sports Rekindle the Rivalries. Sign up for Fantasy Football

I have built latest Asterisk w/ OpenH323 channel driver. We have a SIP softphone registered to the Asterisk. We can place outbound calls from the SIP phone to the PSTN via OpenH323 connection to our gatekeeper. Everything works okay - DTMF and Audio... But in the reverse - if we call from a cellphone or landline the PSTN number we can get the SIP phone to ring - we answer and can hear the

Has anyone had any success with the Rhino CB-24? I can't get mine to work, I tried all the obvious settings. The cb-24 gets stuck at init ESF framing, as if it's not seeing the t1 card at all. It does get a t1 carrier (detecting voltage??) Help! Thanks.. Everything appears to look good on the server, I did: [zaptel.conf] span=1,0,0,esf,b8zs fxogs=1-24 [zapata.conf] signalling=fxo_gs

Hi everyone, I've just got my X100P card installed and working but there seems to be an issue with hang-up supervision. If I stuff a call out over the X100P card onto the PSTN that's fine. When I hang up the SIP phone the PSTN call ends. If I receive a call from the PSTN, it's answered and everything is ok until the remote party hangs up. Asterisk thinks the call is still active and

Hi there! I'm setting up a connection between Asterisk ver. 1.2.13 and a Harris 20-20 PBX. More less everything went fine, but the problem I have now is when dialing to the Harris PBX, it seems to pick up my call as soon as it reaches it. For example if from the Asterisk outgoing folder I dial an extension, say 100, and play a prompt as soon as it is picked up, the promt is beign played as

Hi, all I have installed TDM400 with 1 FXS and 1 FXP ports. Now I am goig through documentation on how to configure it. It mentions 3 protocols: Loopstart, Groundstart and Koolstart. Which one do I use? Can someone send me sample zaptel.conf file for Australia? This will save me some time and will be used as a working example. Thanks, Rudolf

Hi. Does anyone know about a simple one-fxs ATA with pulse dialing support that can work with Asterisk? A SIP one would be ok. I've been told that the Digium S101i IAXy does support pulse dialing; although it's a iax2-only ata it could be enough. I need a bunch of them to convert some old fashioned rotary phones into VoIP ones (I'd like to disassemble the ATAs to remove the boards

----- Original Message ----- From: "hank" <hanksmith4@earthlink.net> To: "Asterisk Users Mailing List - Non-Commercial Discussion" <asterisk-users@lists.digium.com> Sent: Tuesday, June 28, 2005 10:52 PM Subject: Re: [Asterisk-Users] Shoutcast Music On Hold problems? >I am using asterisk@home 1.0 > my mp3 is called > mp3 > it has nothing before it

Hello, I am having problems configuring a TDM400P 4 Port FXO card with groundstart signalling. The box has 2 X100P's, 1 TDM04B and 1 TDM40B. I can configure it for loopstart and it works, just not groundstart, which I need for this installation. What am I missing? Thanks! Mark /etc/zaptel.conf #two X100P FXO Cards # fxsls=1-2 # TDM400P 4 Port FXO (TDM04B) fxsgs=3-6 # TDM400P 4 Port

Hello! Recently I posted a question about an installation I have that was experiencing glare problems. The solutions presented were to use inverse inbound and outbound line groups and to use groundstart signalling. As it turns out, the Sangoma A400D card that is in use does NOT support groundstart. I've confirmed this with a Sangoma engineer and their support staff. I've also read that