similar to: E1 PRI configuration: DAHDI and LIBPRI

Dear; Thanks a lot for guiding me. Is it possible that the installation libpri-1.4.11.5 newer than the libpri-1.4.11.5-patch? Well, when I typed (note: I am trying to apply the libpri-1.4.11.5-patch for the libpri-1.4.11.5): libpri-1.4.11.5# patch -p0 -i libpri-1.4.11.5-patch It gave me that patched detected as shown below (example of one file, and I got same for other files): patching file

Dears; To patch libpri: I just place the patch file in the libpri source directory and then I run make and make install? Or I need to compile the dahdi and asterisk also? If the problem stayed, do I have to go for previous libpri version? Or for previous dahdi version and asterisk version? Regards Bilal ----------- > bilal ghayyad wrote: > > But I am afraid it is a bug because I

Hi; How can I know the duration that the DAHDI channel is still used? I need to know its status and since when it is in this status, how? Also, is it possible to hangup the channel if it has been openned more than 90 minute? Other than using the timeout in the Dial command (because this I know it). What is happening with me that from time to time, I find some DAHDI channels are stayed connected

Hi All; When the call coming via the E1 dahdi and I handle the call (as first step) by exten => 5631040,1,Goto(OrangeCMG,s,1) it is not working and the call will be disconnected instead of queued. But, when I handle the call (as first step) by playing any sound file and then send for the queue, then it is working fine, WHY? exten => 5631040,1,Playback(WelcomeMessage) exten =>

Hi All; My ISDN was working fine, and suddenly I start getting the below: sig_pri.c:985 pri_find_dchan: Span 1: No D-chanannel anyway! There is a Yellow Alarm, so what it could be the problem? My configuration as following: system.conf span=1,1,0,ccs,hdb3,yellow bchan=1-15,17-31 dchan=16 chan_dahi.conf context=IncomingPSTN group=0 signalling=pri_cpe switchtype=euroisdn

Hi List; How to upgrade the Asterisk, Zaptel and LibPri and keep the configuration the same? I do not need to remove current asterisk, zaptel and libpri and download new one and write new configuration. Regards, -------------- ITS IP Telephony and Contact Center Engineer Eng. Bilal Ghayad Mobile: 00965 9849460

Dears; The problem was related to something else. The Digium card has two PRI ports, actually to get it UP, I have to configure the two ports and both of those two ports to take the timing from span 1. Why this, I do not know ! Although I am using only one E1 connected to span 1, so why I have to configure the other span !! After configuring the second span, so now one D channel for span 1 is

Hi All; I need to use a gateway that converts from SIM to E1 to I can send and receive calls via the GSM, so did any one use a good gateway for this and reliable and stable and costly effective, so he can advise us to use it? Also, it will be a separate product if we need also to use it for SMS (send and receive), also we need a reliable and constly effective product for this. Thanks in

Hi All;

Hi All; Again, the Cisco IP Phones 7942G and using Skinny: I upgraded the firmware to version 8.5 (skinny) and I am using skinny channel (chan_skinny) and the skinny.conf file. The phones are registering, but when we use them to place a call, we only hear tooooooooooo in the handset and we do not hear voice (even when we dial the digits, we only hear toooooooo .. but it dials and destination

I am current running on a production system zaptel 1.4.12.1 libxpri 1.4.1 asterisk 1.4.25 The above configuration works. I tried to update to dahdi 2.2.0, libpri 1.4.7 and asterisk 1.4.25 This did not work. calls came in but not out. I dropped back to the initial configuration. Today, I dried only updating libpri on the original configuration. I removed /usr/lib/libpri* installed libpri 1.4.7,

Hi All; If I set a context other than the default context, then I do not see a generation for a configuration in the extensions_additional.conf for this context, but always the generation for the configuration is for the default context (from-internal). Normally, I have to put some Phones in a context and another Phones in a context, and give each context a privilages, but if I do this, then I

Hi List; Asterisk does not have any kind of cards that can work with it to be used with Digital Phones (digital phones differ than analoge phone and differ than IP Phones). Anyone can advise about this as I did not find this on Diguim Regards Bilal Ghayad __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around

I googled about a bit without success, so... Is there a version matrix available? Something that would say: for kernel version w, you can run up to version x of Asterisk, DAHDI version y, and libpri version z? For example, I have a bunch of remote hosts running kernel 2.6.26, Asterisk 11.6.0, and DAHDI 2.7.0.1. We experience occasional Asterisk crashes, so I'd like to get as up to date

Hi, I would appreciate some advice on the following: how does one use a single BRI port HFC chipset based ISDN cards with the latest DAHDI, libpri and Asterisk 1.8? For Asterisk 1.4 I would first install mISDN & mISDNuser and then build Asterisk 1.4. Now I noticed that Digium's HFC chipset based B410P is supported by the latest DAHDI & libpri but reading the source of the

I'm putting together a PBX using a TE420P card configured for E1s that is connected to an Errickson MTS. successfully compiled and installed libpri 1.4.11.3, DAHDI 2.3.0.1+2.3.0 and Asterisk 1.6.2.9. everythings seems to be working. SIP phone to SIP phone (POLYCOM) calls work fine however, network calls do not. When I went to debug PRI, the only command that showed up when I did ">CLI

Hi, I need to rebuild a system which has 4 BRI ports and is connected to Point-to-multiPoint lines, in a country where telco often "drop lines for energy savings". I'm planning to use latest 11.4.0 asterisk version along with dahdi and libpri (no misdn). Which version are recommended for Dahdi and Libpri ? My main requirements are, beside having calls coming in and out: - keep a

Hi All; Can anyone advise if using Cisco IP Phones in skinny protocol is fine or not? Or it is better to use it in SIP protocol? Regards Bilal

Hi, Has someone successfully deflected calls using a Digium BRI board enabled asterisk ? How would you describe your experience ? Which Asterisk, Libpri and Dahdi versions are required for this ? Regards -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.digium.com/pipermail/asterisk-users/attachments/20111011/6e746640/attachment.htm>

Hy guys i am having so much hard time to setup asterisk on a virtual machine that i got , i just want to know if i really need to use Dahdi and libpri on a complete Digital PBX i just gonna use sip and iax. I will never use any kind of analog line on this machine. Wait for a feed back. Daniel Abreu.