similar to: Why high latency on internal lan?

My internal lan is small, 100mb, all wired. aastra phones. sip show peers ....... 142/... 10.10.10.42 D A 5060 OK (136 ms) 144/... 10.10.10.44 D A 5060 OK (138 ms) 145/... 10.10.10.45 D A 5060 OK (133 ms) But pings are < 1ms: ping 10.10.10.42 ........ rtt min/avg/max/mdev = 0.479/0.483/0.497/0.021 ms Why are the sip latencies so

extracted wine-0.9.60 and ran ./tools/wineinstall , it configured and compiled. then after putting in root password I getcould not find wine on your system.run wineinstall as root to install before rerunning wineinstall as a user. So I enter root and root password and then i retry ./tools/wineinstall and get WINE Installer v0.75 You are running wineinstall as root, this is not advisable. Please

Newbie trying to install wine in his Mac OSX, getting the old annoying message, home:~/Desktop/wine G3$ /Users/G3/Desktop/wine/tools/wineinstall WINE Installer v0.75 Running configure... configure: creating cache config.cache checking build system type... powerpc-apple-darwin8.7.0 checking host system type... powerpc-apple-darwin8.7.0 checking whether make sets $(MAKE)... no checking for gcc...

I've * in a small office with 10 internal sip extensions on aastra's. Outgoing is pstn over dahdi, voip over teliax and iax to another office. This morning no calls could be made: iax to branch offfices, voip iax over teliax, pstn, or even internal extensions. The aastra's showed "Not in Service". A "core restart now" got everything working again. Before I

Am 23.06.2020 10:07, schrieb Marek Greško: Hi > this is a correct response: > > From 62.156.246.57 (62.156.246.57) icmp_seq=1 Frag needed and DF set > (mtu = 1492) > > So PMTU discovery is working. No problem here. You got correct message > to lower the packet size from 62.156.246.57. This is probably the last > hop before your site. No, the last hop is 62.156.246.65:

Hello, this could be ip address of the different interface on the same box. I think it works like expected. The only exception would be if the sip peer ignores the icmp packet unreachable. But I doubt this is the case. Anyway you get problems also when calling to LTE phone without using sip provider. Let first concentrate on these calls LTE to LAN. Are you sure you do not block incoming icmp

Am 23.06.2020 09:28, schrieb Marek Greško: Hi > if you need clampmss then it is highly probable there is a PMTU > discovery problem. The clampmss does not work for UDP. Is there a way to check if I have this problem? > I probably counted the size incorrectly. So you are able to ping with > size 1464 and not with 1466. How about trying same ping sizes from the > internet towards

ok i have been using linux for about three days now and i must say it is pretty cool. my only problem is that when i tried to update halo pc to play online wine froze. so when i tried to do it manually by clicking on halo update.exe everything seemed to download fine until it started to update. then it had some weird error about internet explorer. here is a picture [Image:

I'm trying to move the asterisk server to an Amazon Web instance. We have teliax for our sip provider. I'd like for our DID lines to be connected to a users cell phone. Seems simple enough, but I'm getting the dreaded one-way audio, even with nat=yes everyplace I can think of. The dialplan is real easy: [from-teliax-sip] exten => _j.,1,NoOp("From teliax sip with exten

I am experiencing a "606 not Acceptable" error trying to set up an Asterisk server as an ekiga.net client. My server is behind a firewall with NAT routing. I have googled this problem and read about Asterisk feeding its local ip address to ekiga.net. That seems to be my problem. I tried putting stunaddr=stun.ekiga.net into the sip.conf file under [ekiga]. I also tried

Keith, Thanks for the reply and the pointers. > Did you remember to activate kernel ip forwarding? > i.e. echo 1 > /proc/sys/net/ipv4/ip_forward ? I actually forgot to do this, but I have enabled it now in /etc/systctl.conf and can confirm now after a reboot that it's enabled. Unfortunately, still can't ping the node on the LAN. > and when I saw that I was about to cancel

Hi All, I've got a realtime queue in place (strategy is "wrandom"), and have added a member dynamically via "queue add member ". My agent shows in the queue, but when he gets the call is not recognized as "In Use". Here is the output from "queue show" prior to the call: *CLI> queue show QUEUE_3 has 0 calls (max unlimited) in 'wrandom'

Package: xen-hypervisor-4.4-amd64 Version: 4.4.1-9+deb8u3 Severity: grave Hello, I am trying to install the XEN Hypervisor on a Debian Jessie Server. When I am booting without the Hypervisor, everything works fine, but when I am Booting WITH the XEN-Hypervisor, then System crashes / reboots after the "Scrubbing Free RAM" Message without any Error-message, just a blank screen.

I am trying to send calls from (telx-NY17S) to (telx-nyc) via an IAX2 channel. However the call is being rejected on the (telx-nyc) server. See error below copied from telx-nyc CLI> Apr 22 13:56:57 NOTICE[147465]: chan_iax2.c:5390 socket_read: Rejected connect attempt from 192.168.0.251 I have icluded the following conf files 1. extensions.conf (telx-nyc) 2. iax.conf (telx-nyc) 3.

help me in another issue related also to registering asterisk with another softswitch: A) If nat=yes, then I have to set canreinvite=no to be able to register, correct? B) In case of using firefly softphone, how it possible to set it to have nat=yes (at the firefly it self and not at the sip user configuration section)? As most of the sip endpoint give an option to set nat=yes and so on, how it

G'Day All; So I purchased a Cisco 7960 and am now trying to get it configured for *. No can do without the variuos files/images through a FTPF server. I configured the TFTP server on my RHES 3 box, now to get the required CISCO files. So I contacted CISCO to purchase the required maintenance contract so as to gain access to the download area for the files/images. -WHAT A FRUSTRATION!!-

I just tried to order the CON-SNT-CP7960 part from CDW. This is the ~$8 1yr support contract that's supposed to give access to the Cisco download site for firmware for the 7960 . wellll, I got a call from CDW saying that Cisco wouldn't authorize them to sell that product to me. The sales rep conferenced me in with the CDW Cisco person and he explained that CON-SNT-CP7960 is an

Hi all, Happy Wednesday! Got a 7940G off eBay to tinker with and, per the wiki, contacted Cisco about a service contract. Being just little ol' me, they won't deal directly and blew me off (I hate dealing with Cisco, Nortel, etc as a small-business person...) Again per the wiki, I hit CDW.com and found CON-SNT-CP7960 for $9.14. Looking for support for the 7940 (not 7960), I just

Thanks everyone for your feedback, especially Mark. I now have the ALL the files I need. My order still stands for the $8.00 product from CISCO but the CP7960 dealer sent me all the files. Now I will move on to completeing the setup of the TFTP server. Thanks again -----Original Message----- From: Michael Loftis [mailto:mloftis@wgops.com] Sent: Friday, February 18, 2005 7:51 PM To:

Hi, I have an Optimus-enabled laptop with a GTX 1060m. I never got it to fully work with Nouveau even after Pascal support was added. I need to run the kernel with nouveau.runpm=0 to get it to work. Unfortunately without proper power mangement support, my laptop will run out of battery after about 1h30, so I'd love to get Optimus working. What I can see is that when the extra GPU is not in