similar to: Asterisk 1.4 and TE420P

Hi, I just read a pressrelease from VON that Digium will soon be releaseing a couple of new cards. What got me interested was: "The TE420P and TE415P support 128ms of G.168 (2002)-compliant echo cancellation across their entire 128 channels." Does anyone know when thease will be released and what they will cost when released? Thanks!

Hello I am trying to configure TE420P but i am confused what to give chan_dahdi :( Below is configuration i am using for TDM400P Please help what changes to make in it... Please provide a link as well [trunkgroups] [channels] ;default for channels switchtype=national rxwink=300 hidecallerid=no callwaiting=yes usecallingpres=yes callwaitingcallerid=yes threewaycalling=yes transfer=yes

Hi I've been noticing an odd issue with our servers (1.4.17) where a large number of one particular customer's (we operate a hosted VoIP platform) calls go through a Local channel rather than the SIP channel and whenever this happens our asterisk CDR is recording a billsec value of 0. Our outgoing calls to POTS are sent through a separate carrier and we get a daily CDR off them in

Dear, I have asterisk 1.6.2.13 in a small hardware PBX (512 GB RAM and Celeron), and last days when I call from one extension to another of the same PBX after I dial the number the rings sound after 20 seconds. In the CLI log, when I debug the AGI, I see always goes good until dialparties.agi, and after that there are 20 seconds without any log, and so the ring sound. I've read

Hello: We have a TDM2433E Digium Card (12 FXS, 12 FXO) and Asterisk 1.8.7.0 running. Everything seems to be ok but call transfers. This is the issue: *A, B, C and D are in FXS ports*. 1) A calls B. B anwers. 2) B tries to transfer the call to C dialing *2 (code for attended transfer). 3) A hears MOH. B dials number C. 4) Asterisk says the dialed number is incorrect or non existing. We tried

Hi, I've been meaning to fix my non-working paging feature here for a while, and I've just spent the last 5 hours looking at many, many web pages that all say the same thing. I am using Asterisk 1.6.2.18 and Polycom phones, both older (501 with "latest" legacy 3.1.7 firmware) and newer (335 and 650 with latest 3.3.1f). I have changed the correct values in sip.cfg like

I'm trying to decide if I need to open an issue for this or if it's just a misconfiguration issue of some sort. Here's the situation - yesterday morning, I downloaded asterisk 1.8.19.1 and installed it on a fresh CentOS 5.8 installation and got a shell of a basic asterisk install setup (minimum required configuration files, etc, with no dialplan or sip peers setup yet). In the

Hello, For those customers with only analog lines, who ask for fax2email and email2fax, whats the most reliable solution available and tested with Asterisk? Thanks -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.digium.com/pipermail/asterisk-users/attachments/20120529/3e28b56e/attachment.htm>

Hi All; If I set a context other than the default context, then I do not see a generation for a configuration in the extensions_additional.conf for this context, but always the generation for the configuration is for the default context (from-internal). Normally, I have to put some Phones in a context and another Phones in a context, and give each context a privilages, but if I do this, then I

Hi All; When the call coming via the E1 dahdi and I handle the call (as first step) by exten => 5631040,1,Goto(OrangeCMG,s,1) it is not working and the call will be disconnected instead of queued. But, when I handle the call (as first step) by playing any sound file and then send for the queue, then it is working fine, WHY? exten => 5631040,1,Playback(WelcomeMessage) exten =>

When I receive a call, I want to automatically park it from the dialplan so that I can retrieve it later. However, I don't want callers to be aware that they are being parked, so I want to play a ringing tone to the caller. Park() is supposed to be able to do this: Park([timeout][,return_context[,return_exten[,return_priority[,options[,parking_lot_name]]]]]) options r: Send ringing

Hi All; Again, the Cisco IP Phones 7942G and using Skinny: I upgraded the firmware to version 8.5 (skinny) and I am using skinny channel (chan_skinny) and the skinny.conf file. The phones are registering, but when we use them to place a call, we only hear tooooooooooo in the handset and we do not hear voice (even when we dial the digits, we only hear toooooooo .. but it dials and destination

Hey Guys! I am getting this wired error when i am calling IAX trunk. Everything works! but i want to get rid on these RED WARNING messages.. what is wrong here ? I have func_aes.so module loaded. also i remove and test but still same error. -Satish == Using SIP RTP CoS mark 5 -- Executing [7623 at from-sip:1] Macro("SIP/7527-0000000d", "orasebcamdial,7623") in

NEWBIE alert: i'm a linux person, not an asterisk person so i'm certainly capable of handling any linux-flavoured solution you can suggest. here's a note i got from a local company i know (some proper names removed): ===== start ===== Now and again our ISP goes down and when it does give us a hicup, the Asterisk system shuts down (not very forgiving). When it shuts down our phone

Can you say a Virtualized Asterisk with a PRI card! http://www.phoronix.com/scan.php?page=news_item&px=OTY0OQ Doug -- Ben Franklin quote: "Those who would give up Essential Liberty to purchase a little Temporary Safety, deserve neither Liberty nor Safety."

someone have been installed Asterisk (Trixbox) on VirtualBox which is installed on a Linux host (Ubuntu server 10.04 specifically). I want to know if it is convenient or not, and the reaseons if i should on shouldn't do it. Thanks in advance.! -- Esteban L. Cacavelos de Amoriza Cel: 0981 220 429 -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi all, I'm getting one way audio when calling over the SIP trunk i.e. end device B (remote end of SIP trunk) can hear device A (softphone registered with Asterisk) but device A can't hear device B. Even though I configured same NAT configurations on other servers and they are working good. The NAT configuration is listed below; localnet=130.0.0.0/130.0.0.0 externhost=12.131.12.13

I have an *ipphone 7965G* which has to be connected to Asterisk. It has been flashed with SIP firmware but the config file doesn't seem to work maybe I am missing something in it. I appreciate it if you can share your working sample config file with me. Thanks -------------- next part -------------- An HTML attachment was scrubbed... URL:

I am running Asterisk 1.8.10.1. I am trying to set up some routing in my dial plans and having some issues (the issue being that I don't quite understand all of the syntax and patterns that can be used: Examples: DID1 = 6140000000 DID2 = 6140000001 CNAME1 = 6149999999 CNAME2 = 6149999998 CNAME3 = 6149999997 context1 context2 context3 I have looked at several examples (patterns) and I

I'm trying to declare a few date-related global variables to ease my dialplan. When I declare the following in the [globals] context of extensions.conf, I get unexpected results: YEAR = ${STRFTIME(${EPOCH},,%Y)} MONTH = ${STRFTIME(${EPOCH},,%m)} DAY = ${STRFTIME(${EPOCH},,%d)} TIMESTAMP = ${STRFTIME(${EPOCH},,%Y%m%d-%H%M%S)} If I evaluate these variables in the dialplan later, using exten