similar to: p2p or p2mp for BRI

hello: thanks for Tzafrir Cohen for dahdi testing. I installed dahdi-2.1-r3c svn code and asterisk1-6 for testing OpenVox B400P and junghans card. i fund that there is bug (i think) to dectect NT or TE mode. actually on the board, i set it as TE mode, but after start wcb4xxp, but it show the port is NT mode. to detect the TE mode, I modefy the code in base.c

Hi list! I am installing an * box that will be installed on a site with KPN BRI ISDN in The Netherlands. I am using bristuff fron Junghanns. Does anybody know the correct settings for this? I will not have internet access there which makes it harder to google around on location. switchtype = euroisdn is pretty obvious but what about these settings: signalling = bri_cpe_ptmp ; p2p TE mode

Hi- Anyone using the Junghann's quad BRI card and the Digium E100P in the same system? I'm having a configuration problem where I can configure the cards one at a time (with the appropriate drivers loaded) in a system, but when I try them both together, neither will work. They both work fine one at a time. Probably has something to do with the channel numbering. I've tried

Hi, I'm trying to connect quadbri between powered ISDN phone and ISDN line: ISDN <---1---> TE - * - NT <--2--> Phone I use quadbri, suse 9.2 and latest 0.2.0-RC7k bristuff. I've used sample settings provided with package, but do get strange error (I think that I have wrong setting for P2P or P2MP setting and cables 1 and 2). If I connect phone to ISDN with straight cable

Hi All ... I'm running Asterisk 1.2.13-BRIstuffed-0.3.0-PRE-1v which has a Junghanns QuadBri card in it (lspci reports Cologne Chip Designs GmbH ISDN network Controller [HFC-4S] (rev 01)) I have a regular KPN ISDN2 Line connected which works fine with the the zapata.conf below. However, I also have a new KPN ISDN Mutli (meervoudig) line (PBAX-Group), which works fine for incoming calls,

Hi all, this time with the complete configuration files... We need help with our SuSe9.2 asterisk box We have one QuadBRI and one TDM40B in an ASUS pundit R-2 barebone. We have downloaded the bristuff (0.2.0-RC7j) and installed it without problems. once we downloaded and compiled asterisk, zaptel and all other stuff, the module installation succed in this order: modprobe zaptel modprobe qozap

Is there a recommended way to find out the cause of DIALSTATUS = CONGESTION for PRI/BRI channels? Currently I am evaluating the DIALSTATUS variable and I also count the active ISDN channels for the ISDN trunk in question. Counting the active ISDN channels seems somewhat clumsy as the mapping to a specific trunk must be done by hand (or write even more code). I have a setup where outgoing calls

Hi I have a small ISDN PABX , (BRI) at home - Siemens Gigaset 4175 which has cordless DECT extensions. I have set up asterisk on FC3 with two HFC cards and I am using the latest bristuff. I am trying to use * between my ISDN line and my PABX. One card is in TE mode and can receive and make calls OK. I can make and receive external calls to a SIP phone. I cannot get the other card to talk to my

Hi, When startin * it tells me: ================================ [chan_zap.so] => (Zapata Telephony w/PRI) == Parsing '/etc/asterisk/zapata.conf': Found Sep 3 17:21:59 DEBUG[1076873856]: chan_zap.c:1208 update_conf: Updated conferencing on 1, with 0 conference users -- Registered channel 1, PRI Signalling signalling Sep 3 17:21:59 DEBUG[1076873856]: chan_zap.c:1208 update_conf:

Hello all Asterisk 1.2.10 BRIstuff PRE-1s Debian sarge I have an issue with my ISDN-BRI line. Asterisk tells me my D-Channel is down, no matter is I have an actual line plugged in or not. == Primary D-Channel on span 1 down I somehow got it to work once! The config tools do not indicate any errors whatsoever. Here is a rundown of various listings I can think about. (some things may show

Hi! Has anybody seen anything like this using zaphfc? On outgoing calls (via isdn) , the line gets hung-up as soon as the called party answers. As seen below i get some protocol error (6) - but i'm not sure if this is related to the "hang-up" which apparently comes a little earlier?! Incomming calls on the isdn (zaphfc) interface is working just fine (P.S. what about the

Hello, I always thought that Energy Savings mode existed with ISDN Basic Rate Interface in Point -to-multi-Point but it didn't with Point-to-point. Is this correct ? Have you ever met a public PSTN switch configured to "cut" B ISDN channels in Point-to-point.signalling ? Regards. -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi ""noobs"" and others(like me). I've been struggling for hours,days,days,days.... to get my Asterisk work with 2x HFC-S BRI cards. One card for use in NT-mode for connecting my ISDN DECT phone,and one card as gateway to PSTN. Now it'works,and I just want to share some of the experience with others. I'd guess there must be 'Somebody Out There' having

Hi all, i'm trying to install Asterisk with Junghanns QuadBri ISDN card: I have followed all the instructions, and when I run "|ztcfg -tvv" I get | | Zaptel Configuration ======================| SPAN 1: CCS/ AMI Build-out: 399-533 feet (DSX-1) Channel map: Channel 01: Individual Clear channel (Default) (Slaves: 01) Channel 02: Individual Clear channel (Default) (Slaves: 02)

Hello, I have an installation in Austria; ISDN service provided by Austria Telekom. The main number of the service is 6 digits. Incoming calls may contain 2 additional digits, which I then use to route the call to the correct extension. Telekom sends me all the digits. My problem is that when someone tries to dial an 8 digit number to an extension from an outside analog phone, AT sends the call

Hi, i've downloaded/compiled/installed the bristuffed asterisk Asterisk 1.0.7-BRIstuffed-0.2.0-RC8a and i'm using it with an hfc card. It runs on a debian 3.1 sarge machine with kernel 2.6.11. Asterisk works well if i configure the card using isdn4linux. I'm having problems dialing out (not tried the input yet). This is the output from asterisk: -- Accepting AUTHENTICATED call from

Hi, I have debian etch 4.0 machine (2.6.18) with two TW-ISDN PCI (Hfc) cards. I use bristuff-0.3.0-PRE-1y-e (asterisk-1.2.17,libpri-1.2.4,zaptel-1.2.16). I also have patched zaphfc with zaphfc_0.4.0-test1_florz-13.diff.gz (I load module: insmod /usr/src/bristuff-0.3.0-PRE-1y-e/zaphfc/zaphfc.ko modes=1 debug=1). So i want to test two cards and make loop between them. So one card would be NT,

Hi all, I have a strange problem, regarding zap channels and cdr. I am using asterisk bristuffed version Asterisk 1.2.2-BRIstuffed-0.3.0-PRE-1i, Copyright (C) 1999 - 2006 Digium, Inc. and others. with two billion ISDN cards. I also installed asterisk addons, last stable version via cvs internal calls, or calls starting from internal sip or iax phone are recorded in the cdr all without any

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 hi, i'm new to * I've installed an hfc-s card (DIGI Micro V) with bristuff 0.0.2; when i try to call outside i get: -- Accepting AUTHENTICATED call from 192.168.1.110, requested format = 1024, actual format = 1024 -- Executing Dial("IAX2[pippo@pippo]/2", "Zap/g1/0123456") in new stack Jul 13 13:42:49

Hello, I cannot make any call with my new quadBRI card from Junghanns.net in my asterisk box. My asterisk box is built on Fedora Core 3 linux system. After compiling drivers from junghanns.net the card driver was loaded correctly with - modprobe zaptel - insmod qozap.ko ( as FC3 is running a 2.6 linux kernel) - ztcfg -vvv ( shows 12 channels correctly configured and the 4 leds on the card were