similar to: B400P and A1200P changes card order

Hi, I have a B400P BRI card with point-to-point connection (signalling: bri_cpe) with this dmesg: http://pastebin.com/sXrRt1yM When i restart asterisk server, the card cannot connect to the telco, the control led flashes red. If I unplug the cable between the ISDN nt and the card and wait 40 sec, the card can connect and works properly. The telco says the asterisk crashes the connection

Hi all, Does anyone have any good/bad comments on the A1200P 12-port fxo/fxs card from OpenVox? I'll be using one to with 8-12 fxo interfaces.? The cards will be plugging into a cable-modem / phone adapter.? We weren't able to port the numbers, so we're going to use the existing PSTN connection and replace all of the office phones. With these short distances, will I need to worry

hello: thanks for Tzafrir Cohen for dahdi testing. I installed dahdi-2.1-r3c svn code and asterisk1-6 for testing OpenVox B400P and junghans card. i fund that there is bug (i think) to dectect NT or TE mode. actually on the board, i set it as TE mode, but after start wcb4xxp, but it show the port is NT mode. to detect the TE mode, I modefy the code in base.c

lspci | grep Digium 03:05.0 Ethernet controller: Digium, Inc. Wildcard TE122 single-span T1/E1/J1 card (rev 11) dahdi_scan So I have a card in a box - lspci shows it... dahdi_scan reports nothing. Is my card dead? Jerry -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi, I have a B410P card with bri_cpe signalling and two Openvox analog card (A1200p, A800P) with fxo_ks signalling. From the ISDN we have Point-Point 10 connection with a 10 public phone number range. If I receive a public call, the asterisk recevies the last two digit from this range, so it works, I can receive all the 10 numbers. If I'd like to dial from an exten which I have to

Hi everybody, In an Asterisk 1.6.0.5, dahdi-linux-2.1.0.4, dahdi-tools-2.1.0.2, with a Digium B410P and an OpenVox A400E, I can't make "dahdi_scan" to recognize the OpenVox. This card was working correctly but suddenly stopped working and I cannot make it work again. Both ?lspci? and ?dahdi_hardware? detect it but ?dahdi_scan? not and I cannot use it. >lsppci: *0a:00.0

Hi, I'm using Sangoma's wanpipe together with dahdi, all software downloaded today at most recent version. Hardware is Sangoma A104, a 4xE1 card. Installation went well. Anyway, wanrouter status shows a different result than dahdi_tool or dahdi_scan. I've just put a hardware loop on port 1. All the other ports are open. wanrouter status shows the expected result: Device name |

Hi, I'm trying to dial from one Asterisk box to a Patton 4638 BRI gateway. I'm only getting this : [May 8 15:08:24] WARNING[16797]: app_dial.c:1547 dial_exec_full: Unable to create channel of type 'DAHDI' (cause 0 - Unknown) My setup is : Asterisk 1.6.1.18 libpri 1.4.10.2 1 Junghanns QuadBRI PCI-E express with : - driver

Hi, I''m using CentOS 5.5 x86_64 xen 3.43 from gitco.de and I have an Openvox A1200P voip card and am passing it thru to another centos 5.5 DomU, when I 1st start the domain driver loads and everything seems quite nice and the device works, but after a reboor of the DomU, this is shown on my Dom0 dmesg Here''s Dom0 info [root@xen ~]# dmesg Bootdata ok (command line is ro

Hi, I''m using CentOS 5.5 x86_64 xen 3.43 from gitco.de and I have an Openvox A1200P voip card and am passing it thru to another centos 5.5 DomU, when I 1st start the domain driver loads and everything seems quite nice and the device works, but after a reboor of the DomU, this is shown on my Dom0 dmesg Here''s Dom0 info [root@xen ~]# dmesg Bootdata ok (command line is ro

Hi, I run into a problem and I'm not shure what do I misconfigure. I've a B410P ISDN card with bri_cpe signalling and two Openvox (A1200, A800) cards with fxo_ks signalling, all with dahdi drivers. I can receive fax from a public number, but I can't send fax. The CLI says it picks up the line but no dialing. I tried the extension with an analog phone, it works fine, I can dial

Hi, I need a feature from asterisk with dahdi channels, if there is an incoming call, it should ring on several dahdi channels. My channels look like: OFFICE1=DAHDI/13,,rtT OFFICE2=DAHDI/14,,rtT If I add this line: exten => 12345678,1,Dial(${OFFICE1}&{OFFICE2}) only OFFICE1 rings. If I change it to exten => 12345678,1,Dial(DAHDI/13&DAHDI/14) DAHDI/13 and 14 rings together,

Hello! I am trying to configure my digium TE220 dual-span pci express card with Dahdi. I seemed to have managed to set up the card with the Dahdi kernel, as demonstrated by executing dahdi_scan: [1] active=yes alarms=RED description=T2XXP (PCI) Card 0 Span 1 name=TE2/0/1 manufacturer=Digium devicetype=Wildcard TE220 (4th Gen) location=Board ID Switch 0 basechan=1 totchans=31 irq=16

Hello, I have previously open a topic on the mailing list about deadlocking on Asterisk 1.2.35. After upgrading to 1.4.29.1 we still experienced the same problem : Mar 5 12:05:56] DEBUG[8647] channel.c: Avoiding initial deadlock for channel '0xb7689840' [Mar 5 12:06:41] DEBUG[7130] channel.c: Avoiding deadlock for channel '0xb7c04788' [Mar 5 12:06:41] DEBUG[7130]

Hi, When typing dahdi_scan on an OctoBRI-enabled setup, I've got only 8 replies such as : [1] active=yes alarms=RED ... [8] active=yes ... framing=CCS I would expect 16 replies (one per B-channel). Is this correct ? Regards -------------- next part -------------- An HTML attachment was scrubbed... URL:

Tengo en una maquia ubuntu 8.10 el kernel es Linux 2.6.27-14-generic Quiero configurar una tarjeta x100p i usarla con asterisk, asi que descague compile e instale lo siguiente: asterisk-1.4.24 dahdi-linux-2.1.0.4 dahdi-tools-2.1.0.2 libpri-1.4.9 Sin embargo no logro configurar la tarjeta con exito, ya probe casi? todo. Esto aparece si ejecuto lspci: 04:06.0 Communication controller: Motorola

Hi, Built a new server at the weekend and install Asterisk 1.6.0.9 and IAX and SIP work great :) The one problem I am having is getting the OpenVox (TDM400 type card) to work. It is successfully identified using WCTDM kernel module and dahdi_scan picks it up just fine. The issue is when I try and setup dahdi_channel.conf as it fails everytime. When running asterisk -rvvvv I see the port pick

We need to monitorate the E1 with nagios, somebody did this? any ideia? Thanks in advance! -- Atenciosamente, ------------------------------------------------------- Dario Quiroz (71) 9275-9080 gtalk: darioquiroz at gmail.com ------------------------------------------------------- -------------- next part -------------- An HTML attachment was

I have an Asterisk 1.2.16 server running CentOS 4.4 with a TE110P card and an OpenVox A1200P card. Up to today everything was working perfectly. The OpenVox card has 8 FXS and 2 FXO ports. The two faxo ports are used for a GSM adapter and for an ATA connected to Vonage. The problem we started noticing today was that the Vonage line will receive a call and then cannot connect to any of the SIP

Hi As you may''ve seen from my last posts I''m struggling to get the setup on my subject line to work without flaws. I''ve tried compiling the Kernel from Source, I''ve also tried Fedora 14, which has a flaky pv_ops Dom0 kernel which DOESN''T work at all, but none of these seem to work. I''m a mid-time XEN user, I just love it and want to stay