similar to: Is restart of span a concern on PRI?

Hey everybody, I've, within the last 3 weeks, moved over to a PRI from SBC/AT&T. I've received several complaints about dropped calls. Reviewing the archives on PRI and dropped calls shows that I should set the resetinterval=never in the zapata.conf and restart. This hasn't helped. The dropped calls have to date only been on outbound calls. Usually within 2 to 3 minutes

Hi All, Hope you all are fine and good, Today i have found that Mine all PRI Channels are restating after every interval of one hour, and i have search and psot on fourms and everyone said that this is a normal behaviour. If this is a normal behaviour is there is any way to stop it { i still don't know what is the reson to restart ever hour } . Because this is listed everywhere that

Has anyone else had this symptom? It seems like my PRI ?restarts? each hour. I?ve got a PRI from Qwest in central California. What I don?t know is if this is on the * side or on the telco side. I don?t use my system enough to know if this is a big problem, a minor glitch or just an ?undocumented feature? - ? Any suggestions on how to track the source of these ?restarts?? Anybody else seen

Hi Guys I have a 4 port PRI card that I need to setup each port in their own group. In chan_dahdi.conf I have the following which works for one port How do I add the rest of the ports in their own groups so that I can have different signaling on each? [channels] language=en switchtype=euroisdn pridialplan=unknown resetinterval=600 echocancel=yes echotraining=yes

Hi, I've an PRI coming to my asterisk ,calls are coming fine and my agents are able to answer no prob. but I've an agreement with my telco with some incoming no if the no of calls on these no are more then 3 then send to another no. they use busy signal to divert call on another number so I'm sending the call to Congestion() if no of calls in this group are more then 3. But my

I must be doing something stupid, but I can't figure it out. I have three PRI lines connected to Asterisk, one from the phone company, and two more connected to PBXs. Asterisk uses the incoming DID information to decide which PBX to route the call to. Should be simple. Asterisk is clearly getting the caller id info from the phone company: -- Accepting call from '512345xxxx'

Hi, I'm buying an interface for my Toshiba DKT424 to connect to *. Initially it is a trial to route internal calls over our wan. Think of it as a tie trunk between 2 pbxs. I expect to get PRI from the telco our layout will be like this: telco_T1_PRI to * to various PBX or TDM or IAX to * to other pbxs My question is, is there benefits to connecting with PRI over a standard T1 within my

We are using AAH with Asterisk 1.2.7.1 with a TE405P as listed below. We are getting frequent restarts on the spans which lead to dropped calls. I have pasted some hopefully pertinent information below -- anyone have any clues that might help? Thanks Next line is repeated throughout messages, going through every channel in every connected span. asterisk/full.1:Apr 24 01:15:25 VERBOSE[4196]

Hi, Lately we've noticed that some Zap channels on one of our PRIs are unavailable. We have 2 PRI lines with 60 channels in total. On the first PRI there are currently 20 channels that are not being used for some reason. I tried googling around and found some similar problems but there really was no solution (?). I'm not sure if this problem has occured now because of more load on the

Hello, I have an ISDN-30 connection and a Digium TE-121 with VPMADT032 echo cancellation. Every 30-60 minutes I experience PRI dropping. @@@ /etc/zaptel.conf: loadzone=dk defaultzone=dk span=2,1,0,ccs,hdb3,crc4 bchan=32-46 dchan=47 bchan=48-62 @@@ @@@ /etc/asterisk/zapata.conf [channels] switchtype=euroisdn usecallerid=yes group=2 signalling=pri_cpe context=incoming channel => 32-46

Hi all, Strange request, I have a customer where we are putting an Asterisk PBX in front of a legacy (non-VoIP) PBX. One of the requirements it that the Asterisk PBX have 2 PRI ports (on towards the legacy PBX and one towards the carrier) with the ability to go to pass through should the Asterisk PBX (software or hardware level) fail. I did not see this feature in the Digium, Sangoma, Allo, or

4 Port PRI sangoma a104 From: jg [mailto:webaccounts173 at jgoettgens.de] Sent: Wednesday, March 18, 2015 2:09 PM To: Andrew Colin; Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [asterisk-users] 4 Port PRI I have a 4 port PRI card that I need to setup each port in their own group. In chan_dahdi.conf I have the following which works for one port How do I add the rest

Hi all OK this may sound like a good one but maybe someone can tell me. Simple context is - I want to unplug my existing conventional PBX from the Telco and place * with it's TE410P in between. Now the difficult part, the existing connection is E1 PRI (Q.931) with 6 B-channels. I need to be able to trigger a D-channel to the old PBX and a D-Channel to the Telco (Not BT!). Next I can put

Hi All, This posting regarding PRI voice optimization, on dahdi 2.1.0.4. we have more than 4 machine running on 4 port PRI card with echo cancellation hardware based. i have enabled echo cancel from chan_dahdi.conf using echocancel=yes, now more than 70% of call get good voice but some of calls having issue for callquality and other voice related issues. now my question is that is there any

I have 2 * boxes. 1 has 2 PRI's from the Telco, and a PRI to the 2nd * The other has ZAP channels to Channelbanks for endusers. If someone on the second box calls a Toll Free number (it probably doesn't matter that it is toll free) that is auto answered by an auto attendant (QVC, a Bank, the Airlines, Credit Card Companies....) then the call gets dropped with in a couple of seconds of

Hello everyone, My setup: Debian squeeze Asterisk 1.8, DAHDI, libpri, compiled from source TE110P, attached to a Deutsche Telekom Octopus E Modell 300/800 I'm trying to get MWI for Voicemail working. In the same server I have also got an Eicon DIVA PRI card for testing purposes (it is integrated via CAPI and the chan-capi channel driver into my Asterisk). MWI works just fine there. I

Is it normal for a PRI to reset the inactive B channels periodically(like once every hour). I'm seeing on my asterisk console successful restarts, just curious as this is all new to me. ________________________________ This e-mail, facsimile, or letter and any files or attachments transmitted with it contains information that is confidential and privileged. This information is intended only

Hi! I have an Asterisk Box with one E1. This is connected with PSTN. My problem is that periodically the Asterisk console shows the following message. -- B-channel 0/1 succesfully restarted on span 1 -- B-channel 0/2 succesfully restarted on span 1 -- B-channel 0/3 succesfully restarted on span 1 -- B-channel 0/4 succesfully restarted on span 1 -- B-channel 0/5 succesfully restarted on span 1 --

Told you it was too complex of an issue :-) I figured to do this in zapata.conf and all is fine now: transfer=no That was the magic two letter which was sending a request for RLT feature on the line. Set transfer to "no" and all worries gone. Thanks for the input everyone. -Bruce On Mon, Apr 12, 2010 at 10:10 PM, bruce bruce <bruceb444 at gmail.com> wrote: > Futher check

Hi Everyone, This is probably more related to Linux than to Asterisk. Analogue channels on a system were un-responsive on Monday morning. Apparently something happened over the weekend and the router went off or it lost it's DSL connection. [Jul 23 22:50:01] VERBOSE[12437] logger.c: -- Remote UNIX connection [Jul 23 22:50:01] VERBOSE[27087] logger.c: -- Remote UNIX connection