similar to: Use a BLF for monitoring

I'm trying to get the BLF to work correctly on my Polycom phones. I have the buddy watch working correctly, but can't get the BLF to change based on the state... Example: When an extension is ringing, I get the same 'red light' that I get when the extension is actually in use... I was wondering if anyone had any experience with getting the Polycom phone to

I am trying to get something working that is just not doing quite what I want. It may not be possible, but I figured it was worth asking about. The details: Asterisk 11.6.0 Polycom SoundPoint IP650 phones running 4.03 firmware. We have a queue with 4 phones in it. ringinuse is set to yes and the stategy is ringall. In sip.conf, we have notifyringing set to yes as well. Asterisk is sending

We have an issue where Polycom's lose BLF functionality after a reboot. The only way to fix it is to reboot the Polycoms. Anyone else have this issue? We are using 1.4.18. If I run 'sip show subscriptions' all the subscriptions come back after the restart but the lights on the phones do not work. Any help would be appreciated. -Thermal -------------- next part -------------- An

I have meetme working with BLF on polycom phones however when meetme is not actually being used by anyone the 'status' of meetme becomes "idle". Which the Polycom phone sees and produces a clock symbol and FLASHING red LED. Are there any 'tricks' or work-arounds to change this status to something that does not blink the phone's LED making it look busy when meetme is

Would anyone happen to have some examples of polycom configs, specifically the 650 with sidecar for blf. I have the asterisk side all configured since I've set up blf with other types of phones, but I'm missing the polycom side. I've put together a <mac>-directory.xml, and the sidecar now lists numbers as speed dials but does not subscribe to blf.

Hi all, I am working on asterisk 1.2.18 zaptel 1.2.17 Polycom 650 polycom 430 SIP version 2.0.3.0131 for IP 650 SIP version for IP430 2.0.3.0127 freepbx 2.2.1 I am trying to configure BLF using asterisk but failed. I would be thankfull if somebody help me. Regards FArooq ********************************************** 1 ********************************************** in my

Hi all, I am working on asterisk 1.2.18 zaptel 1.2.17 Polycom 650 polycom 430 SIP version 2.0.3.0131 for IP 650 SIP version for IP430 2.0.3.0127 freepbx 2.2.1 I am trying to configure BLF using asterisk but failed. I would be thankfull if somebody help me. Regards FArooq ********************************************** 1 ********************************************** in my

----- Original Message ----- > Subject: Re: [Asterisk-Users] Analog Phones with Status Light Indicators > From: Adam Goryachev <mailinglists@websitemanagers.com.au> > To: asterisk-users@lists.digium.com > Organization: Website Managers > Date: Thu, 12 Aug 2004 14:53:02 +1000 > Reply-To: asterisk-users@lists.digium.com > > On Wed, 2004-08-11 at 20:42, Steven

Is is possible with a Polycom phone to update the LCD with the callee's name after dialing them? When you dial ext 103 now, it says 'To:103'...would be nice if could have 'To:Dan Marino' This is the case even when you have a contact for ext 103. None of the phones I have ever tested do this, Polycom, Linksys, Cisco, Grandstream, Yealink, etc. -Matt

Has anyone been able to do the following: 1. Set the phone to automatically record all calls to the USB stick, now you have to press three keys. 2. Put Record on the main screen when a call is active. This would eliminate having to press the 'more' softkey. Thanks, Matt

Aloha, Anyone know how to disable call forward on a Polycom Phone. Calls being accidentilly being forwarded somewhere is the #1 trouble that we have to respond to. The real issue is the 'end call' button becomes 'forward' when the call ends....therefore the user thinks they are pressing 'end call' but the call ends just before they press the button so they end up

Hi all, I have a Polycom Soundpoint IP 600 that looks like it is fried. It either has a bad or corrupt bootrom (I'm guessing). It never gets to the prompt that asks if I want to enter the setup configuration or continue booting. When plugged into power, it turns on, shows the Polycom logo for 3 seconds and then pretty much goes dead with two red lights on. The one in the top right corner

I have a 536i expansion module attached to a 57i-CT. The BLF lights on the 536i will light up and work fine for a while... however after a bit they seem to loose their ability to see if someone is on a phone. They still work to dial, if I try to dial, however, they don't light up when someone makes a call, or if their phone rings. If I reboot the phone, the lights start working again

Aloha, Are there any hard phones that support ILBC? I see lots of soft phones but not Cisco, Polycom etc. Aloha, Matt

I am working on Polycom IP601 console with expansion module. I want to put on the BLF (busy lamp field) feature on all the contact/speed dial names I put on the console but I could not get it to work. *CLI> core show version Asterisk 1.4.13 built by root @ hostname on a i686 running Linux on 2007-11-20 05:26:15 UTC *CLI> sip show subscriptions Peer User Call ID

has anyone done it? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20080528/ff622d28/attachment-0001.htm

Hi all, There are a lot of posts around the web about my question; unfortunately I have not been able to get any of the solutions to work. I'm using Asterisk 1.6.2.8 under CentOS 5.5. I'm trying to get call pickup working for the secretaries that monitor their bosses' phones. The BLF and the speed dial works great on the Linksys phones. Call pickup is the problem. My features.conf

Hello We have recently upgraded our internal PBX from 1.4 to 1.8. This made the BLF lamps on our Polycom phones stop working. After a lot of googling and a lot of testing, I have been unable to find a solution. I did try to change the call-limit value from 4 to 1, and this actually made BLF work (noone suggested this, and what documantation I can find states that this option is deprecated). This

Hi, We have a user who is putting large call volumes through Asterisk, and wants to BLF monitor up to 90 extensions. We are struggling to find a handset that can keep up with Asterisk :) 1) Is there a handset that will do this? 2) Is there a different (standard) way to send BLF and allow directed pickups? 2a) Or even a handset specific way? Asterisk handles the BLF volume fine, even on quite

I remember seeing something like this on the list a while ago, but I'm darned if I can find it. We have a number of Polycom IP501 phones, some of which have more than one registration on them. When a voicemail is left for a phone with only one registration, the MWI lights up and stays lit until the voicemail is listened to. However, on our phones with more than one registration, the MWI