similar to: question on pri intense debug

hello, In a machine I've got : CLI> pri set debug off No such command 'pri set debug off' (type 'core show help pri set' for other possible commands) CLI> core show help pri pri intense debug span <no description available> pri service disable channel Remove a channel from service pri service enable channel Return a channel to service pri set debug

I'm putting together a PBX using a TE420P card configured for E1s that is connected to an Errickson MTS. successfully compiled and installed libpri 1.4.11.3, DAHDI 2.3.0.1+2.3.0 and Asterisk 1.6.2.9. everythings seems to be working. SIP phone to SIP phone (POLYCOM) calls work fine however, network calls do not. When I went to debug PRI, the only command that showed up when I did ">CLI

Hello my friends, I would like to understand the output from "pri intense debug span X", the Telco always says that their side is OK, but i always receive alarms, loosing connection, take a look: [Sep 16 13:18:19] WARNING[30364] chan_zap.c: Detected alarm on channel 1: Recovering [Sep 16 13:18:19] WARNING[30364] chan_zap.c: Unable to disable echo cancellation on channel 1 [...] [Sep 16

Hi, I have the following setup: Ubuntu 12.04.02 LTS (64 bit) Asterisk 11.2.1 Sangoma 4-Port-Card (A104d) with firmware 43 (german e1-ports connected) WANPIPE Release: 3.5.28 DAHDI Version: 2.6.1 Echo Canceller: HWEC libpri version: 1.4.12 I call via sip into the dialplan. Then I do a "Dial(DAHDI/g1/voicenumber,r)". The call is bridged and everything is fine. "dahdi show

Hi Guys, Running the following with a Sangoma A101D PRI card: *Asterisk 1.4.21.2* *LibPRI version: 1.4.10* No inbound or outbound calls can be made. In fact Asterisk CLI doesn't show any activity. Problem goes away on restart of the system or maybe asterisk. I see post about upgrading Libpri to 1.4.10.2 and then I see posts that even that didn't work. Anyone can weigh in this please?

In article <CAHZ_z=w5DMg93gShtC93kuC+fnmraPgV46BS956U5BQXVgyhxg at mail.gmail.com>, Matt Fredrickson <creslin at digium.com> wrote: > On Tue, Apr 3, 2018 at 5:44 AM, Tony Mountifield <tony at softins.co.uk> wrote: > > I have some more investigation to do on this, but I wanted to see if anyone > > here had any insight into the issue I've run into. > > >

I have some more investigation to do on this, but I wanted to see if anyone here had any insight into the issue I've run into. The hardware is a HP DL360 G6 with a TE420 gen 5 4-port T1 PRI card. It is one of several systems that have been running without issue since 2010/2011. They have all been running CentOS 4 32-bit with Zaptel 1.4.12.1 (with patch for gen 5 card), libpri 1.2.8 and

Hello, I'm experiencing some weird problems on my server: - 1) The following messages are filling up my logs: [Sep 29 08:24:59] WARNING[7077]: chan_dahdi.c:2789 pri_find_dchan: No D-channels available! Using Primary channel 140 as D-channel anyway! [Sep 29 08:24:59] WARNING[7078]: chan_dahdi.c:2789 pri_find_dchan: No D-channels available! Using Primary channel 171 as D-channel anyway!

Hi everyone, I'm trying to get a Sangoma A101D-X card talking to a Sasktel PRI (Megalink) circuit and having some trouble getting it to handshake. Thanks for any help or suggestions to diagnose this problem. The problem is that Asterisk has trouble bringing up the link. I see the following lines every couple of minutes: == Primary D-Channel on span 1 up == Primary D-Channel on

I have been getting quite a bit of PRI Resets using my Quad PRI Digium card. Prior to the resets I am getting similar notices to the following chan_zap.c:7482 pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 3 Telco claims the PRI's are fine on their end and that it is my unit. Is this timing? (google somewhat leads to this) I am running 1.08 asterisk zaptel

I am running Asterisk 1.0.9 and have been running all my calls through a VSP over a IAX2 trunk however we have recently purchased and connected a TE110p to a PRI ( E1 with 16 voice channels ) through Optus. I can make outgoing calls via it fine, however incoming calls are dropped after a few seconds ( or as soon as a command like Playback, or the call is picked up if forwarded to a SIP

Hi All, I am looking for a way to troubleshoot issues with TDM (E1) trunks with a provider. Currently with SIP trunks I am using tcpdump to perform packet captures between our gateways and the SIP providers IPs, capturing traffic on all ports, to include both the SIP messages and the RTP stream. How can I achieve a similar result on TDM links connected to TDM cards in Asterisk servers, where by

After working fine for a week or so my new Quad E1 asterisk 1.8 system has started rejecting outbound calls from the Nortel BMC 450 it is connected to. The cli fills up with these: sig_pri.c: Ring requested on unconfigured channel 255/255 span 3 Is this likely to be a 1) config error 2) cable issue (I made them) 3) hardware problem with the Digium card 4) software (lib pri) Any clues?

Hi, Does anyone have any good empirical data suggesting what the maximum number of PRI calls (incoming and outgoing) without hardware echo cancellation can be handled on a single box is? I have a TE410P T1 (1st gen) card and I'm seeing interesting errors of D-Channels going down and then coming back up (See below). I've looked at the number of simultaneous calls at each of these points,

Hi, After an upgrade, I discovered yesterday strange things I would like to share here. Basically, I'me comparing platforms: The first one is a 2.6.26 (Debian Lenny) platform, with Asterisk 1.6.1.18, Libpri 1.4.10.2, Dahdi revision 8853 (must be between 2.3 and 2.5, I think). The second one is a 2.6.32 (Debian Squeeze) platform, with Asterisk 10.5.1, Libpri 1.4.12, Dahdi 2.6.1. Both are

hi folks. recently some of our customers complained about bad voice quality on the phone system. i looked at the logs and found a lot of these: [2012-11-03 08:26:38] NOTICE[11305] chan_dahdi.c: PRI got event: HDLC Abort (6) on D-channel of span 1 [2012-11-03 08:26:45] NOTICE[11305] chan_dahdi.c: PRI got event: HDLC Abort (6) on D-channel of span 1 [2012-11-03 08:26:54] NOTICE[11305]

Hi everyone! Everyday some channels go to this situation: # asterisk -rx 'pri show channels'| head -n 32 | grep 'Yes No Idle Yes' PRI B Chan Call PRI Channel Span Chan Chan Idle Level Call Name 1 1 Yes No Idle Yes 1 2 Yes No Idle Yes 1 6 Yes No Idle Yes 1 13 Yes No Idle Yes 1

Hi all, Does Asterisk contain a full fledged ISDN packet sniffer. By giving the command " pri intense debug span 1 " , does it debug every packet received (control and voice/data packets) ? Thanks -- Arpit Mehta Graduate Student Department of Computer Science Columbia University Tel: 1-646-387-5998

Ok Guys, I've done a tonne of hunting around on this problem, but can't find much help. I'm running: asterisk 1.4.19.1 libpri 1.4.3 and zaptel 1.4.9.2 which I believe has been modified by RedFone to add the ztd-ethmf module. My interface is a RedFone foneBridge2 4 Span; and I'm connecting to a BT E1 PRI / ISDN30e with 15 lines on span 1, and a legacy Panasonic PBX on span 4. Upon

I have a TE405/TE410P card that was working on 1.0.X I upgraded the OS to Centos 4.5, Updated asterisk to 1.4 and zaptel to 1.4.5 and libpri. I copied all the zaptel and zapata and extensions.conf files from 1.0 I did update extensions.conf from 1.0 to 1.4 commands. I cannot get the card to work in 1.4.10. AHHH! I see with zttool that the T1 is in Green, I see calls coming in as the bits go