similar to: ZAP and line disconnection detection

Dear Folks, Anyone knows if Sangoma supports or going to provide support for battery removal detection on FXO lines?? As Tzafrir said earlier DAHDI supports it, which is a very nice feature but what about Sangoma? Regards. -- M. Shokuie Nia. -------------- next part -------------- An HTML attachment was scrubbed... URL:

As far as I can tell, after discussing this matter with other asterisk users in my area, my telco _does_ provide disconnect supervision.. It seems that the problem is actually related to the Sangoma A200 card I'm using, as two other people both using this same card have expressed the same problem.. Are there any other users on this list using the Sangoma A200 FXO port card, and experiencing

Hi I have been having a rough time getting a Sangoma A200/Remora FXO/ FXS Analog AFT card set up properly. The main issue is that the card has four ports and as far as I can tell Asterisk is only seeing two. On the two that it recognizes the "Green" FXS ports are not green, they just are not lit. The "RED" FXO ports are indeed red, but from what I have read your not

Can anyone help me start to diagnose why a Sangoma A200 wouldn't dial out LD? Local calls are fine, incoming is fine, just no LD. Bell tech has been on site and plugged into lines with his test set and was able to dial LD just fine, so it's not a LEC issue. No errors in asterisk console, using zaptel 1.4.11 and sangoma drivers 3.2.6, asterisk 1.4.18 ________________________________

I'm using Asterisk 1.4.5 (will try 1.4.6 on Thursday, but I don't see anything in the changelog after the 1.4.5 release dealing with distinctive ring), zaptel 1.4.3, and wanpipe 2.3.4-10 with a Sangoma A200 card. I enabled usedistinctiveringdetection in zapata.conf. However, on the Asterisk console, the output I get is: -- Detected ring pattern: 0,0,0 It would appear that Asterisk is

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi all! I had the opportunity to test a Sangoma A200 card and I have some doubts that I would like to consult: I tried to detect the card and I had no success using the wctdm module with DAHDI. I guess this is because electronics is different because the TDM400P and OpenVox A400P cards have separate modules for each channel, while the Sangoma A200

Hi all, Just want to check from the list experienced personal about the Digium HPEC, where I had purchased the HPEC and wish to run with TDM card Sangoma A200. I can't install HPEC to run with Sangama A200 card, even I had changed my hpec file from i686 to i386. The error that I had as bellow; > Found key 'HPEC-XXXXXXXXXX' for 2 channels. > Found valid HPEC licenses for 2

Hi, got a Sangoma A200 with a bunch of extension cards and having real problems getting it to deal with a normal single BT line Symptoms are that incoming calls are fine. Outgoing calls ring the far end, BUT asterisk never sees that the call is answered (ie no message in the logs files saying so), as a result the remove end can hear the PBX side talking, but there is no audio back from the

Evening all. I'm looking at building an Asterisk system for one of the projects of the Charity where I'm the SysAdmin. The project has two analogue phone lines - BT Featureline Compact, we're in the UK - that I'd like Asterisk to handle. My current quandary is which FXO interface to use. I've been looking at the Digium TDM400P and Sangoma A200, which are similar prices for

Good morning :) Am 04.01.2024 um 20:17 schrieb lists--- via samba: > Am 04.01.2024 um 13:28 schrieb lists--- via samba: >> Am 04.01.2024 um 12:36 schrieb Rowland Penny via samba: >>> On Thu, 4 Jan 2024 12:12:57 +0100 >>> lists--- via samba <samba at lists.samba.org> wrote: >>> >>>> Am 04.01.2024 um 11:55 schrieb Rowland Penny via samba:

Hi: I have a Sangoma A200 card installed in a server with two FXO modules and one FXS module. Analog sets connected to the FXS module have a "squeaky static" -- it's like static mixed with the sound of someone vigorously cleaning a window a few doors down. In other words, it's not a classic static noise, but it is noise, and it's distracting. Remote callers can hear this

Hi, I have A101DE Sangoma Card( http://www.sangoma.com/products/hardware_products/digital_voice_and_data_networking/a101.html ) lspci shows as 03:04.0 Network controller: Sangoma Technologies Corp. A200/Remora FXO/FXS Analog AFT card [root at asterisk ~]# lspci -vvv -s 03:04.0 03:04.0 Network controller: Sangoma Technologies Corp. A200/Remora FXO/FXS Analog AFT card Subsystem: Unknown device

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi all! I'm testing a telephone connected to FXS port of a Sangoma A200 card. But I'm observing that callerid is not working. The configuration that I'm using in chan_dahdi.conf is the following one: - --------------------------------------------------------------------- ;autogenerated by /usr/sbin/wancfg_dahdi do not hand edit

Hi - I just got an A200 card with 1 FXO and 1 FXS module. Sadly, I can't make it work- currently, asterisk will not startup because of a bad module. Below are some log files/config files. If anyone has any suggestions, I'd appreciate it. I used Trixbox 2.0 and followed instructions on (http:// sangoma.editme.com/wanpipe-linux-asterisk-atHome) - no problems running through or

Hi All, What do you recommend? I was looking at: http://www.voipon.co.uk/sangoma-a200-fxo-fxs-analogue-card-pci-express-p-393.html But it will be 3 PCI slots. Thanks, Gavin.

Hi - I just got a Sangoma A200 card with a single 2FXO module and what appears to be an empty module. I put the card in my Dell GX260, but the power light on the front of the box just blinks and won't power up. I did take the power cable from the CDROM to put on the card - I don't need the CDROM right now.. I'm looking for direction in getting this card working - I currently

Hi all, I have setup a Dell PowerEdge 2550 with a Sangoma A200 card with 2xFSO and 1XFS modules. The PowerEdge specs are 1 x P3 1133MHz, 512MB RAM. Sangoma A200 has 3 analogue PSTN lines connected. This server is based in Office 1, with 5 users all with a Linksys SPA942 VoIP Handset. There is another Office (Office 2) connected to here using VPN. There are two users in Office 2 with the

Hey Everyone, Has any successfully installed this on a Toshiba A200? Any feedback would be great. Kind Regards Matthew Ollerenshaw Network Engineer * +612 1300 887 959 | Ê +612 9890 8349 | * mollerenshaw@visinet.com.au<mailto:mollerenshaw@visinet.com.au> | www.visinet.com.au<http://www.visinet.com.au/> Diploma (Network Engineering) | Microsoft Certified Professional ( MS

I lost one channel on an FXO module on a Sangoma A200 card due to a lightening zap in the area (well - it died the same night as a major thunder storm came through).... Is there a recommended/standard surge protector for phone lines I should be using? My server has 2 POTS lines. thanks Todd

Hi all I'm using sangoma a200 cards in the UK and have the ongoing, often noted problem of disconnect supervision with BT POTS lines. Just noticed this post on http://www.voip-info.org/wiki/view/UK+Asterisk+Details stating that potentially someone's got a solution : "TDM400P &amp; Not Detecting Hangups: Got a TDM400P installed and having problems with Asterisk not detecting