similar to: Problem configuring TDM400

Hello I'm trying to install Dahdi through source code on a Fedora 13 host to use an OpenVox PCI card with a single FXO port, but dahdi_cfg -vv isn't happy. 1. After successfully running "make all; make install; make config", I edited /etc/dahdi/system.conf thusly: loadzone=fr defaultzone=fr fxsks=1 2. Then ran "dahdi_cfg -vv" which says: ------------- DAHDI Tools

Hi. I am having problems with dahdi using kernel 2.6.32. I am using 2.6.30 kernel and it works fine -- here is the output of dahdi_cfg -vv ++ dahdi_cfg -vv DAHDI Tools Version - SVN-trunk-r8670 DAHDI Version: SVN-trunk-r7445M Echo Canceller(s): Configuration ====================== Channel map: Channel 01: FXO Kewlstart (Default) (Echo Canceler: mg2) (Slaves: 01) Channel 04: FXS Kewlstart

Hi few weeks ago I read about redundancy (HA) of asterisk boxes using DNS, DUNDi, so I decided to give it a try. OS FreeBSD 6.1-RELEASE, asterisk 1.2.7.1 on one peer I get: lk110*CLI> dundi show peers EID Host Model AvgTime Status 00:11:43:3d:69:e6 195.28.109.37 (S) Symmetric Unavail OK (1 ms) 1 dundi peers [1 online, 0 offline, 0

Hi, yes, it is. Anyway, below are some of the diagnostics I have tried. Linux box Win95 Box ========= =========== hostname: saturn tempest ip: 192.168.0.2 192.168.0.1 Below are the diagnostics that I have tried and I ahve logged them: 1. From

Hello group, I am installing Asterisk on a new pc running Ubuntu 12.04.3 Server. ?I have dahdi-complete-2.7.0.1+2.7.0.1, and have tried 2.6.1 and 2.8.0-rc1 and 2.8.0-rc2. ?I am following along in the ASTERISK The Definitive Guide 4th Edition and on page 116 when I issue the command $ sudo /etc/init.d/dahdi start I get the following error: Loading DAHDI hardware modules: ? ?wctdm24xxp: done

Hello, After installing on Ubuntu 10.04 using the tutorial on http://hmontoliu.blogspot.com/2010/03/installing-asterisk-and-freepbx-on.html I have a running instance of Asterisk. PROBLEM: result of dahdi_cfg: DAHDI Tools Version - 2.2.1 DAHDI Version: 2.2.1 Echo Canceller(s): MG2 Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Echo Canceler: mg2)

Hello all, Ok it is Sunday afternoon and I am going crazy. I have been running in circles so long that I can't think straight. As an example, I sent this message to the wrong address the first try, AAARRRRGGGGGGHHHHH. I have Asterisk 1.6.0.6 and DAHDI Tools Version - 2.1.0.2, DAHDI Version: 2.1.0.4, OpenSuSE 10.3 x86_64, tdm422 at the end of installing dahdi-linux and dahdi-tools I get:

Hello No matter if I use the entry-level OpenVox A400 with a single FXO module or the most-often-garbage card from ww.x100p.com, I get the following error after just adding this card to Mini-ITX with a single PCI slot (OS = CentOS 5.4): ============ # lspci -v 03:00.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface Subsystem: Unknown device b100:0003

I have a TDM400. Just updated Fedora 12 to kernel 2.6.32. Rebuilt and installed dahdi-2.2.1. kernel modules loaded. lsmod | grep wctdm wctdm 37233 0 dahdi 194985 1 wctdm lsmod | grep dahdi dahdi 194985 1 wctdm crc_ccitt 1549 2 dahdi,isdnhdlc dmesg: dahdi: Telephony Interface Registered on major 196 dahdi: Version: 2.2.1

As best i could figure it out, I've installed dahdi and rc4. My TDM400P doesn't answer fxo or fxs. /etc/dahdi/system.conf: loadzone = us defaultzone=us fxoks=1,2 fxsks=4 /etc/asterisk/chan_dahdi.conf: [house-phones] context=internal ; Uses the [internal] context in extensions.conf signalling=fxo_ks ; fxo_ks Use FXO signalling for an FXS chanel dahdichan => 1 ;

John R Pierce wrote: > wait. would deleting the inode /sys/(whatever) actually modify UEFI > memory? sure, writing to those inodes could do all sorts of harm, but > deleting the inodes in the /sys filesystem, I'm not so sure this isn't a > tempest in a teapot so to speak. It's going to get /boot. And under there, it'll get /boot/EFI. mark

Hi I have a Dell PE2300 with a Digium TDM400P line card in it (with one module to handle an inbound phone line). This is running on a Fedora 8 system with Asterisk 1.4.21.2-1.fc8 This system has been working nicely for about 12 months. After a recent move of office and relocation of the server Asterisk is back on line, but the TDM line card has stopped working. I have spent half a day

Hi All, I have installed asteriskNow with Asterisk 1.6.2.11 and FreePBX 2.7.0.10. I have configured x100p fxo card in my asterisk box. But in my cli mode i am not getting the command *"dahdi show status"* Output of CLI : astrisks*CLI> *dahdi show status* No such command 'dahdi show status' (type 'core show help dahdi show' for other possible commands) I

Hi All; To overcome the echo problem, what mainly I have to do in the configuration other than the following line in the system.conf under dahdi directory? echocanceller=mg2,1-16 1) How can I know if the digium card supporting echo cancellator? 2) If I am getting a message in the consol that unable to enable the echo cancelator, then what does it means? The hardware is not supporting echo

I am trying to backup an entire disk to a USB-mounted disk, for backup purposes. Many files are copied, but eventually rsync dies: $ rsync -axHSv --delete /backup /media/sda1 ... rsync: connection unexpectedly closed (239508 bytes read so far) rsync error: error in rsync protocol data stream (code 12) at io.c(189) I am running Suse 9.0 and rsync 2.6.0 on an AMD-K6-2/450 (192MB RAM, 400MB swap).

Hello, My first attempt to get dahdi running on 1.4.28... with a Rhino 8 port modular card and a single FXS module. Got the Rhino card installed and the machine sees it: root at pbx:/etc/dahdi# dmesg | grep rcbfx [ 71.985309] rcbfx 0000:04:00.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 [ 71.985440] rcbfx 1: Rhino PCI BAR0 50100000 IOMem mapped at ffffc90008d7c000 [ 71.985504]

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi all! Days ago I bought a OpenVox A400P card with a port FXS and another FXO that I am testing with my Asterisk installation in my house. I'm using Asterisk 1.4.24.1 with DAHDI Linux 2.1.0.4 and DAHDI Tools 2.1.0.2 on Debian GNU/Linux Lenny. I was reading "The future of telephony" and this [1] document looking for information about

Hello there I have been trying to install HP Storageworks DAT72 on CentOS 5 in vain. On system reboot, neither /dev/st not /dev/sg is available. May you please lead me through as this is my first time trying to do it lsmod Module Size Used by ipv6 267617 40 xfrm_nalgo 13381 1 ipv6 crypto_api 12609 1 xfrm_nalgo autofs4

Ok fellows, This is my last try. Please, anybody tell me if something is missing on this list! I need to setup on a Linux + Samba (PDC) to restrict just one login per ID (not allow two logins with same id).So: 1 - edit /etc/pam.d/samba -> chaging session line with session required /lib/security/pam_limits.so 2 - in /etc/security/limits.conf: * - maxlogins 1 3 - in smb.conf:

Hi all! Is it possible to use a usb printer from a DomU? I don''t get to see any device using both lscpi and lsusb. I''m using Xen 3.0.2-2. Thanks in advance. Regards, Daniel -- Daniel Bareiro - System Administrator Fingerprint: BFB3 08D6 B4D1 31B2 72B9 29CE 6696 BF1B 14E6 1D37 Powered by Debian GNU/Linux Etch - Linux user #188.598