similar to: Sangoma A104d and Adtran 850 problems

Hi all, I've done this a few times with other PBX's but swyx has stumped me! I'm having some trouble getting Asterisk connected to a Swyx system using a sangoma A104dx... currently the setup is: BT <-> Swyx The above setup works fine... what i'm trying to achieve is BT & SIP Trunks <-> Asterisk <-> Swyx I have connected to our BT (2 x ISDN30 UK) with

Hello, We are having issues with a NEW Sangoma A108D: -- Executing [691918892 at pbx1:1] Dial("SIP/xtravoip200-009d24b0", "DAHDI/g0/691918892|30|m") in new stack [Oct 1 10:04:43] WARNING[14171]: channel.c:3170 ast_request: No translator path exists for channel type DAHDI (native 76) to 256 [Oct 1 10:04:43] WARNING[14171]: app_dial.c:1237 dial_exec_full: Unable to create

Hi all, My problem boils down to these errors: ... Unable to create channel of type 'ZAP' (cause 34 - Circuit/channel congestion) == Everyone is busy/congested at this time This is triggered by lines in extentions.conf such as: exten => _X.,1,Dial(ZAP/g1/${EXTEN},,W) The system is CentOS v5.2 with Asterisk 1.4.23 (druid-asterisk-1.4.23.1-2), a Sangoma A104

Hi, Recommending to go Digium because of an OpenBSD issue with the Sangoma A104D is quite funny to say the least since neither is the TE407P supported in BSD by Digium. So the recommendation is useless to the person who originally requested for a comparison between the two products. If someone wanted to send back the A104D, he could have taken advantage of Sangoma's 30 day money back

Has anyone had experience with one or both of these cards? I'm in a position where I might need to recommend one over the other. I've read everything that I can find online, so now I'd like to hear of personal experiences. Everything I read on both cards is "5 stars! Awesome! It Rocks!" They both seem to have similar capabilities, similar pricing, etc. Could those of

Hi, I am facing an audio-problem with the dial application and I (!) think, that it is connected to the dahdi parameter "overlapdial=yes". Sangoma support does not see any connection between this. But when enabling this option I face with some(!) dial-partners a audio one-way issue (the called party can not be heard). Only using PSTNS (germany e1 trunk) - no voip. Is there any

Hi all, I need to setup call using particular timeslot on one of E1's. I've looked into http://www.voip-info.org/wiki/index.php?page=Asterisk+Zap+channels and it says that: exten => TestTrakt,1,Dial(ZAP/1-2/517255333) exten => TestTrakt,2,hangup should work and force call setup via span 1 (port 1) but when I try setup call rasterisk says: -- Executing [TestTrakt at

Hi, I am trying to validate a setup with a sangoma A116 card (16PRI in one card). I currently have two machines set up, each with a sangoma A116 card. Those are interconnected with crossed PRI cables. One of them is in NT mode, the other in TE. The ports are configured in E1 mode, asterisk is all set up and I can make calls between them, filling up all 480 (16 * 30) channels. Now, I learned

Hi all, as good? I try to install asterisk-1.2.14, zaptel-1.2.12,libpri-1.2.4,addons-1.2.5 , sounds-1.2.1 and wanpipe-2.3.4-3 and hwec-utils-beta4-2.3.4 But it is not compiling drivers of the Sangoma, why udev's for board in "/dev/zap"(1-31, channel,ctl,pseudo,timer) is not created. But when I install a board TE110P Digium, udev's is created and asterisk functions perfectly. : )

I have used asterisk-1.4.14, zaptel-1.4.7, chan_ss7-1.0.0 on FC7 all went okay. using sangoma a104dx on both machine. I followed the write up on http://www.voip-info.org/wiki/index.php?page=Asterisk+ss7+setup I have the cross over cable between them. however, wanpipe shows connected but the signaling link does not align. i have my configs for host A ##wanpipe1.conf [devices] wanpipe1 =

Hi all, Can somebody help me out, to get the call going through to my provider? I connected my A104D Sangoma card to E1/isdn and each I tried to make call I get the errors below. My protocol analyzer can see only setup info and release complete. WIRELESS2*CLI> set debug 9 Core debug was 0 and is now 9 WIRELESS2*CLI> pri intense debug span 1 Enabled EXTENSIVE debugging on span 1 T203

Hi all, I need your lights :) There are many hardware provider for E1 cards on the market, what's your exeperience with E1 and what's the preferred provider for Asterisk out of Digium? Olivier

Hello all, as good? I am trying to use the package astunicall-1.2.21.0.1 with a Sangoma A104D card and 04 links E1 mfc/r2 in Brazil. The compilation occurred, normally and links is UP if I place in Loop and I obtain to effect called in Loop, but when I extend for the PSTN, links reports the following messages, without asterisk start calls: Dec 5 22:27:12 WARNING[3868]: chan_unicall.c:627

I've replaced 2XTE110 with an A102 with echo cancellation specifically to deal with echo problems. However, user feedback has indicated to me that on some calls (not a lot, but some) the call is unusable, with audio artifiacts, described by one user, as: "very bad phasing reverb & feedback (from my rock & roll days)". This is quite intermittent, as in most cases, the user

Here's my planed setup : PRI from telco <--> (port 1 of A104d) * (port 2 of A104d) <--> PM3 The PM3, for those who don't know is lucent's portmaster RAS dial-up router. I had setup asterisk, zaptel, libpri, wanpipe (as I have sangoma's cards). In wancfg, I have port 1 as TDM_VOICE, with hardware echo on, span 1. Port 2 is TDM_VOICE, without hw echo, Clock as

Hi guys, Can I use a Sangoma a101 to interface a legacy pbx to an Asterisk server? The pbx doesn't have sip and I want to come in off of a sip trunk and interface with the older system. I know I can use a pri card to hook in to the phone network, but can I use this same card to feed back the signaling as if I were the phone company to the older system? Thanks, Tom

I have installed Asterisk on a CentOS4 box and then installed Asterisk from CVS. I installed a Sangoma A101 and connected it to a Adtran 600 using a T1 Crossover cable. The 600 has 12 x FXS, 12 x FXO interfaces. I ran through the wanpipe install instructions and configured it, now I can run [root@altpbx asterisk]# wanrouter hwprobe ------------------------------- | Wanpipe Hardware Probe Info

Do you have any extension in default context of your extensions.conf file to accept incoming calls ? It must be something like; exten => 12345678,1,Answer() exten => 12345678,2,Playback(Welcome) ... 12345678 = The DID number you are calling to reach E1 Idris -----Original Message----- From: Erick Perez [mailto:eaperezh at gmail.com] Sent: Thursday, July 26, 2007 7:03 AM To:

I just wanted to ask about using Adtran boxes to support analog lines into an Asterisk box. Right now x101p's are just too sensitive to RF noise inside the PC. Going with an external chassis looks like a good, albeit expensive option. It looks like I can use the Digium T1 card into an Adtran 850. The Adtran 850 would need FXO cards. It would also need the echo cancellation module. Is

Hi, after many issues we finally managed to make our system do outgoing calls with perfect quality. However I cannot detect *any* form of incoming call. when I use an outside phone to call the E1 connected to the sangoma a102, I instantly get a fast busy tone. My /etc/zaptel.conf is: loadzone=us defaultzone=us #Sangoma A102 port 1 [slot:1 bus:4 span: 1] span=1,0,0,ccs,hdb3 bchan=1-15,17-31