similar to: Help: RED alarm on Wildcard TE122 card

I have recently built a single-T1 Asterisk box using an HP DL120G6 with a Digium TE122 card. I was finding that I was getting missed interrupts on the TE122, causing the driver to report that it was increasing latency. It kept doing this until the T1 did not work reliably. I tried my usual procedure of disabling the USB subsystem in the BIOS (or so I thought), but I found that the USB drivers

Does anyone know if the TE122 is recognized by any of the 1.2 zaptel drivers? It seems that 1.2.16 knows it not... :) Cheers, j

I have setup a asterisk with freepbx, a TE122 and i have an ISDN. My problem now is that callers are experiencing echo. checked on dmesg i saw this: # dmesg -c dahdi: Disabled echo canceller NLP because of CED rx detected on channel 2 i searched google but found no soolution and i have no idea what that error means. below are other details that might be of value. # dahdi_hardware

What's the difference between the TE121 and TE122. I read the description on Digium's site and it isn't clear to me. Best regards, -- Guilherme Loch G?es Visite nossa loja virtual: http://www.shopvoip.com.br Not?cias e F?rum sobre VoIP com software livre: http://www.asteriskexperts.com.br -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hello, I am installing dahdi on a machine lspci 00:00.0 Host bridge: Intel Corporation 3200/3210 Chipset DRAM Controller (rev 01) 00:01.0 PCI bridge: Intel Corporation 3200/3210 Chipset Host-Primary PCI Express Bridge (rev 01) 00:06.0 PCI bridge: Intel Corporation 3210 Chipset Host-Secondary PCI Express Bridge (rev 01) 00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI

I'm not 'overly' new to asterisk, but I am very new to the Digium card / Telco aspect of it. I was able to get a TE110p card, installed.. and hooked a t1 up to it. I'm using zttool to just look at 'some' output. Here is what it looks like when I just load it up: Current Alarms: No alarms. ? ? ? ? Sync Source:

Greetings and I thank you in-advance, I have a system installed with both Trixbox 1.x and 2.x installed and I am trying to utilize a wildcard x100p but it does seem hang-up or release the line. I understand that the Wildcards are not recommended, but I need to get a test system up for evaluation. Here are the steps followed: Run genzaptelconf and red alarm appears in zttool Run again and it

Hello everyone, I bought 2 HFC-ISDN Cards and want to run the first card in NT-Mode an the second one in TE-Mode. Everything looks ok under SuSE 9.1, but I can't dial out. I removed one card, for testing purposes and want to run this one card in TE-Mode. I only want to make a call with my Grandstream BT-101 over Asterisk via ISDN. When I try to make a call I get: ---------------------

lspci | grep Digium 03:05.0 Ethernet controller: Digium, Inc. Wildcard TE122 single-span T1/E1/J1 card (rev 11) dahdi_scan So I have a card in a box - lspci shows it... dahdi_scan reports nothing. Is my card dead? Jerry -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi, We have got a new PRI card at one of our Office locations and now I need to install the the device on a remote server. Is there any way to know if the device is loaded already. When I give " cat /proc/zaptel/* " it returns the following. # cat /proc/zaptel/* Span 1: WCT1/0 "Wildcard TE122 Card 0" (MASTER) B8ZS/ESF RED IRQ misses: 2 1 WCT1/0/1

I am trying to get a zaptel install converted to dahdi. I can get dahdi installed, and the pseudo device even shows up; however, dahdi show channels shows me nothing. There is a TE122 and a TDM800 in there, and neither show up. dahdi show status shows both cards, and dahdi tools show that the cards are there, working, and have no alarms. What am I missing? Michael Munger, dCAP, MCPS, MCNPS,

Just wondering how your experience is with HPEC, Is it just for analog interfaces or we can use it on TE122 as well? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20080214/3f0580f1/attachment.htm

Hello! I run asterisk 1.6.1.0, dahdi 2.1.0.4 with TE122. I always (and only) have missed interrupt when dahdi disables echo canceller (ng2 or oslec- no difference). Dec 29 14:00:54 asterisk kernel: dahdi: Disabled echo canceller because of tone (rx) on channel 1 Dec 29 14:00:54 asterisk kernel: wcte12xp0: Missed interrupt. Increasing latency to 6 ms in order to compensate. Is it possible to

(to mods: sorry for any extra work I've put you through. Posting from my work account, as proper) Hello all, I'm back. I've got that lucky feeling that this will all work out very soon, and I hope that that is true. The issue: In my * server I have a t100P, connected with a T1 crossover cable to an Adtran TA750 with 2 FXO cards. After I do 'modprobe wct1xxp;ztcfg' the alarm

Hi, I've just added an X101P FXO card to my asterisk machine. The card is detected ok but zttool always shows it in a RED alarm state, which I understand means that it doesn't detect the line. I've connected the card via the line socket to my analogue line using the cable that came with the card (and have also tried other cables too) but I always get a RED alarm. I'm located in

Hi On an old IBM Netvista thinclient, the TDM card doesn't detect incoming calls, although the card seems to be detected, and correctly configured: pbx asterisk # lspci 00:03.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface # cat /etc/zaptel.conf fxsks=1 loadzone=fr defaultzone=fr # ztcfg -vv Zaptel Configuration ====================== Channel map: Channel

Hi, It seems like my ATA is making a ringing noise... (as it used to), but now (After the upgrade from 1.0.7 to 1.2) asterisk also is either making the ringing, or passing the PRI ringing from the telco on to me. Any suggestions on how to fix this?

Dear, I have an Asterisk PBX with two E1 cards: Digium TE122 and Sangoma A101D. Sangoma card has SNMP support but Digium card has not, and also SNMP does't give me ral time information. Within CLI Asterisk I execute "dahdi show channels" but I don't get information about channels usage. What is the best way to have real time monitoring of E1 channels usage and status ???

I'm setting up a test server with a Digium TE122 and am getting the following error on the console, spewing as fast as it can. Does anyone have any idea what this error might be? [Oct 19 11:24:53] NOTICE[2076]: chan_dahdi.c:3108 my_handle_dchan_exception: PRI got event: Event 59 (59) on D-channel of span 2

Hello, I am having odd issues with a new PRI based installation. Outbound calls work for all numbers except those that terminate at Sprint! The telco is new to PRI (this is in the Caribbean) and say that Sprint is rejecting the calls, and asked for our PRI settings so they can work with their switch manufacturer. We are using the bare minimum default settings, but I can imagine that a