similar to: What IRQ field from "dahdi show status" means ?

hello: thanks for Tzafrir Cohen for dahdi testing. I installed dahdi-2.1-r3c svn code and asterisk1-6 for testing OpenVox B400P and junghans card. i fund that there is bug (i think) to dectect NT or TE mode. actually on the board, i set it as TE mode, but after start wcb4xxp, but it show the port is NT mode. to detect the TE mode, I modefy the code in base.c

Hi all, As i tested with Asterisk+dahdi+libpri with openvox BRI with NT mode, the ISDN phone does not work. There is the setting and error. ***********************Enviroment***************************** Asterisk-1.6.1.18 dahdi-linux-2.3.0.1 dahdi-tool-2.30. libpri-1.4.11.2 CentOS-5.5 OpenVox B400P ****************************************************************** In my case , I set prot 1 and

Hi all, As i tested with Asterisk+dahdi+libpri with openvox BRI with NT mode, the ISDN phone does not work. There is the setting and error. ***********************Enviroment********************************** Asterisk-1.6.1.18 dahdi-linux-2.3.0.1 dahdi-tool-2.30. libpri-1.4.11.2 CentOS-5.5 OpenVox B400P ******************************************************************** In my case , I set prot 1

Hi, I have a Junghanns QuadBri installed and seems to be detected and working correctly using the wcb4xxp driver All ports are configured as TE The problem is when I connect an ISDN line - the LED turns green and Dahdi status shows Alarm OK But when I try to make a call I get "All circuits are busy" cause 27 I have searched and web and tried numerous configs but it doesn't want to

Hi everybody, In an Asterisk 1.6.0.5, dahdi-linux-2.1.0.4, dahdi-tools-2.1.0.2, with a Digium B410P and an OpenVox A400E, I can't make "dahdi_scan" to recognize the OpenVox. This card was working correctly but suddenly stopped working and I cannot make it work again. Both ?lspci? and ?dahdi_hardware? detect it but ?dahdi_scan? not and I cannot use it. >lsppci: *0a:00.0

Hi all, Last night I went to replace an Asterisk 1.4 + mISDN + b410p box with Asterisk 1.6.2 and DAHDI BRI - to no avail. I had two servers so copied network setting etc from the working one, moved the card across, ran dahdi_genconf etc and it didn't work. Here's the console output with notices disabled: lucas*CLI> pri intense debug span 1 Enabled debugging on span 1 [Dec 16

Dear Supports, I was attempting to install BRI Card(OpenVox B800P) with wcb4xxp in NT mode .But I can not make it worked! Could you please give me some hints? Thanks in advance! Here are my environments: ------------------------------ CentOS-5.3 Kernel-2.6.18-164.el5 asterisk-1.6.1.6 dahdi-linux-complete-2.3.0+2.3.0 libpri-1.4.10.2 OpenVox-B800P(the first port is spliting into

Hi, I have 3 ISDN lines using the digium B410P card. Incoming and outgoing call are working. I use the following version : * libpri-1.4.10.2 * dahdi-2.2.1.1 * asterisk-1.6.2.6 On incoming calls, DTMF is not working, i can't see any logs. Here are the main configuration files : dahdi-channels.conf ;; Span 2: B4/0/1 "B4XXP (PCI) Card 0 Span 1" signalling=bri_cpe

Sir, i am using goautodial server , bri card is showing ok but when i try to call that showing below , This configuration is in doing in dubai , so kindly help me how can connet the call from this , what is my mistake is in this :::chan-dahdi.conf [channels] #include dahdi-channels.conf language=en context=default usecallerid=yes hidecallerid=yes callwaiting=yes usecallingpres=yes

Hi All, I've a BT Versatility PBX that I want to connect to my asterisk 11.9.0 box via BRI port in NT mode but actually I wasn't able to get it working. I've another standalone PBX, it's a Panasonic model, which works fine connected to the same port. The BT connected to a UK BT BRI line works quite fine after roughly a minute once connected. The PBX can be seen at

Hi, I'm using revision 6822 of Dahdi Tools. # dahdi_hardware pci:0000:05:06.0 wcb4xxp+ d161:b410 Digium Wildcard B410P # asterisk -rx "dahdi show version" DAHDI Version: 2.2.0.2 Echo Canceller: OSLEC # cat /etc/dahdi/genconf_parameters ... pri_termtype SPAN/1 TE SPAN/2 TE SPAN/3 NT SPAN/4 NT #

Hi, As mentioned we have the problem that sometimes (could be up to a view times a day) for the calling party (SIP Device) you here ringing. The called party however answered the phone, but hears nothing. The calling party keeps ringing until the phone is hangup. First I thought maybe the card or the server has a problem, so I changed from a PCI beronet 4bri to a Junghanns 4bri PCIexpress and

Hi everybody, I have a 1.6.0.5 asterisk system and I?m having many problems with my pstn cards. This system has a Digium B410P with 4 BRIs configured, and an OpenVox A400E. The issue is that it?s impossible to make the system recognize the A400E, despite the ?lspci? output is: 0a:00.0 Network controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface 11:00.0 ISDN controller: Digium,

Hi all.. I`m with a problem in some E1 cards. The value of Bipolar Viol is too big, and some times the link seems well, but isn`t work correctly, like as if the link is down. Normally, I use to stop asterisk, remove the modules from my card, use modprove to set up they again, and start asterisk, and it come to work, but in some times I have to reboot the server, and then the value of

Hi, 1. Has someone met any success at all, connecting a Digium B410P to a Patton Smartnode 4638 (with latest 5.3 firmware) ? 2. If positive, then, which signalling was used on both sides ? My project's goal is use a Patton Smartnode 4638 to act as telco BRI lines, from a B410P-enabled asterisk box. In my testings, I can see channel is respectively up (with patton web server status page)

Hi, On a (bogus) system equiped with a Digium HA8 and 8 BRI ports, I'm reading this: # asterisk -rx "dahdi show status" Description Alarms IRQ bpviol CRC4 Fra Codi Options LBO HA8-0000 RED 109 0 0 CCS AMI YEL 0 db (CSU)/0-133 feet (DSX-1) HA8-0000 UNCONFI 109 0

I have a 45 x 16 data frame consisting of dissimilarities among 10 colors, giving in each column the 45 = 10*9/2 pairwise judgments for one of 16 subjects. The rownames identify each pair of colors, e.g, "AC" = ("A","C"), and the pairs are ordered by columns in the lower triangle of each distance matrix. > helm.raw <-

Hello, I have a matrix (class matrix) composed of GridCell (row and column). The matrix value is the beta diversity index value between two grids. Now I would like to get the average value of each GridCell. Please kindly advise how to make the calculation. Thank you. Elaine The matrix looks like (cited from Michael Friendly) I would like to get the average value of each color. Obs

I have a system setup with two T1 circuits, the customer complains of call quality issues. I've checked logs and don't see anything too strange, but when I run "dahdi show status" I see: Description Alarms IRQ bpviol CRC4 Fra Codi Options LBO T2XXP (PCI) Card 0 Span 1 OK 0 0 19 ESF B8ZS YEL 0 db

Hello I wonder if anyone here could possibly help me? I am using Samba version 4.5.16-Debian (version information taken from sudo smbstatus) on Raspbian and attempting to prototype some future network infrastructure with a couple of Raspberry Pis. So far I have sucessfully created a Samba 4 AD DC ad1.samdom.example.com. I have successfully joined my Windows 10 dekstop client to the SAMDOM