similar to: no dial to busy sip line

Hi there, I want to set up an extension set that acts different depending on the count of used lines. I have a EuroISDN E1 board with mISDN and I only want to offer 10 lines. Therefore I set up a global variables LINES in the general section of extensions.conf and instantiate it with 0. I a call is incoming I check the LINES variable wether is 10 or more. If so I make a call transfer. If not

Hi, How can I integrate Asterisk to Nuance TTS engine instead of Cepstral? Has anybody done this? How is the architecture and can Java AGI be used to communicate between them? regards, Vela Sivasankaran -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20091021/56254a0e/attachment.htm

I have just got a Cisco 7941G and am experiencing the exact same problem (phone is requesting .tlv file from TFTP server and never asks for .cnf.xml file). The phone originally had SCCP on it, but I downloaded and flashed with the latest Cisco SIP image (8.4(3) released 2009-01-13). In reading your message below, it looks like you were going to try an incremental upgrade?did you have any

Hi, does anyone of you have made it to get the ANI also picked up? I mean: if I fetch a foreign call to me by using the pickup application I want to see the callerID/ANI of the caller to the foreign extension. Is that possible and if yes - how do I achieve that? Regards, Christophorus

Hi list, I have bought some Cisco 7941G-GE IP phones and want to use them with asterisk. Before bying I tested the whole setup with three different models of the old 79X0 series (a 7912, 7940 and a 7960). Flashing the formerly provided SCCP-Image to SIP was no problem, but now it complains about a nonexistent CTLSEP<mac>.tlv file. Most of the howtos say something about an empty file but

hi list, I set up a new asterisk machine with asterisk 1.2.13 and misdn 0.3.1rc27. I use an e1 card with sip clients. My extensions look like this: [E1] <snip>...<snip> exten => 33006733,1,Set(CALLED=${EXTEN}) exten => 33006733,2,Dial(SIP/1@192.168.0.23) exten => 33006733-ANSWER,3,Answer() [SIP] exten => _X.,1,Noop() exten =>

Hi list, I am searching for a possibility to do a certain call transfer method which is called "path replacement" in QSIG. But I want to do that in DSS1 (EuroISDN). If my asterisk does a call transfer I want the machine to signalize on dchan that the call path has to be replaced to a direct connect between the caller and the called, i.e. my machine is to hang up after the transfer and

Dear all, I can't understand the diff between roundrobin and rrmemory strategy. Could you explain for me ? and is roundrobin means each available interface ring once or several times and ring another? ; A strategy may be specified. Valid strategies include: ; ; ringall - ring all available channels until one answers (default) ; roundrobin - take turns ringing each available interface ;

First of all I would like to thank Mark for getting roundrobin to go roundrobin. Good job. Now we have some options here for leastrecent and fewestcalls strategy. It needs some work on the logic and Mark recommend that I ask the list and get some input before he makes any changes to it. fewestcalls from what I have seen would always ring the agent with the fewestcalls first then go into

I have set up an operator queue for our receptionist. That way, if she takes a break or is out, by logging out of the queue, calls to the "Operator" can be handled by other agents. I have set strategy = roundrobin in queues.conf. According to "the book" ATFoT, roundrobin always starts with the first agent in the queue. This is the desired result. I want all calls to start

Hey guys, i'm wondering if there is any good way to get app_queue working in real roundrobin strategy. The idea is to specify a call list of, lets say, 3 agants. Those agents should always be called in the correct defined order. So all calls have to get the following agent priority: 1st Agent -> 2nd Agent -> 3rd Agent I've actually solved that by defining penelty for the accounts,

G'day. I am having reasonable success getting Asterisk 1.4.2 running and doing what I want, but I can't figure out one particular idiom that I want: There are a few situations where I want to have Asterisk push a call through to the first available transport on a list, such as: I have two SIP ports attached to one local (two port) analog phone system. I want to ring line 1 for the

I have a queue setup to 'roundrobin' (NOT roundrobin with memory). I have three agents. We'll call them 101, 102, and 103. When a call comes in.. I want it to always try 101 if no answer try 102.. if no answer try 103, etc. However, what it is doing is... it will ring 101... if 101 answers, next time a call comes in it will go to 102. This isn't at all what I want. Any ideas

I''ve been having a mess of a time using this module, which stinks because its behavior is EXACTLY what I am looking for... whenever I bootstrap new rabbitMQ nodes I want to add them to our HAProxy instance. Here''s my relevant site.pp entries: node /^rabbit.*/ inherits basenode { @@haproxy::balancermember { $fqdn: listening_service => ''messaging00'',

Hello, I am implementing a small call center with 1 to 4 agents. For some reason I don't understand, if an agent is busy, and it is his/her turn in the queue round, asterisk gives an "all destinations are busy" message and hangs up the call. Agents are SIP lines registered with an audiocodes MP108FXS which registers each line independently. Ringing strategy is RoundRobin (most of

I have setup several Calling Queues, each setup with RoundRobin strategy. When I call the queue, the first member/agent phone rings. Great! I call it again, the second member/agent rings?? I thought that was the RRMemory strategy, but it seems RoundRobin is also doing it. Anyone know what I can do to my queues, in order to force each call down the ordering of my members list? --------------

We're moving a somewhat complicated call center over to an Asterisk system, and I'm looking for documentation on queue/agent configuration. So far I haven't found anything on the Digium or Asterisk websites, and I was hoping that someone could point me in the right direction. Thanks, Devon

Dear All, I've got a working asterisk installation which I need minor help from. Currently, I'm running a Sales Queue, which is answered by a selected group of people. Here are my queues.conf [sales-hotline] strategy = roundrobin timeout = 10 member = SIP/602 member = SIP/603 member = SIP/701 member = SIP/604 After calls come in, it works fine, however, I notice that even when SIP/602

Actually doing both sounds good to me. Can you explain further about ringing them all at once? Here is how I tried to make mine work and failed... {global} PHONES0=SIP/2000 PHONES1=SIP/2001 [local] exten => 6001,1,Dial(${PHONES0&PHONES1),20,trf) When I dial 6001 I see my debugger tell me that I am using the wrong syntax. Do you know the correct syntax for ringing them all at once? I

That could be it. What I want to do is set a group of callers and have the event cause the phone to ring them in order. I will tie it to my IVR portion and thus I can make sure peole in sales get calls based on our hierarchy in the office. So if I am reading your example right the syntax is.... Exten => 501,1,Dial(SIP/PHONE1&SIP/PHONE2&SIP/PHONE3), rtf) Is that a valid way to cause