Displaying 20 results from an estimated 9000 matches similar to: "AS5200 <-> T100P - No alarms but no calls either..."
2004 May 25
1
Problem - Adtran TSU 600, t100p
Hello,
I have just received Adtran TSU 600 with 24 FXS ports.
I have installed sucessfuly T100P card.
Adtran is connected to t100p with crossover T1 cable.
On T100P card I have a green light and on Adtran I do not get any
errors or alarms.
But I do not get dialtone on FXS ports.
Adtran is configured: For Network Timing, fxs ports ore fxs_ls on Adtran.
In zaptel.conf:
span=1,1,0,esf,b8zs
2003 Oct 16
3
Adtran TA750 & T100P
Hello,
So all the pieces are finally here, and I'm ready to play. I remember
reading on this list that the connection Channel Bank <-> T100P requires
a "reverse cable." Is this a regular Ethernet reverse cable (i.e., only
a couple of pairs reversed?) Please help me before I blow something up!
Saludos,
Jose.
2004 Aug 22
3
asterisk T100P to Merlin Legend
Management just approved purchase of a Digium T100P and a T1 card for
our Merlin Legend Switch. I will appreciate comments from anyone
performing this installation before:
- Which T1 card did you use in the Merlin Legend?
- Did you require any special interface? (CSU/DSU, etc)
- Any items to watch during installation.
Also we will need to remove one of our old analog Trunk cards to
accomodate
2003 Jun 26
3
use of Asterisk and T100P as Nortel DSX-1?
Hi all,
I've seen a couple of posts recently from people who are doing
something with Asterisk and a T100P and a Nortel PBX. However it's
not clear exactly what they are doing.
Does anyone know if it's possible to use a T100P or T400P as a DSX-1
interface to connect to a T1/PRI CO module in a Nortel PBX? We have
a Nortel Norstar Modular ICS PBX and I'd like to plug its CO
2003 Oct 14
2
T100P to Adtran TA750 - No dialtone or ring
Hello all,
I've got a T100P connected to an Adtran TA750 with a T1 crossover...
This connects to a patch panel with phone ports. The Adtran is fully
populated with FXS cards.
All I get on any phone port is a fast clicking noise... No dialtone.
Asterisk 'sees' the card, (the channels show up in /proc/zaptel).
Incoming calls are routed to the zap/x channel, but no ring.
I'm
2003 Aug 25
4
T100P/ TSU 600 installation problem
I have just received a T100P and an Adtran TSU 600 in
the mail.
I seem to be having a problem with the T100P card. So
far I have done the following:
vi zaptel.conf
fxoks=1-22
fxsks=23-24
...
vi zapata.conf
...
signalling=fxo_ks
...
channel => 1-22
...
signalling=fxs_ks
...
channel => 23-24
I then run
modprobe zaptel
modprobe wct1xxp
ztcfg -vv
There are no errors to report. In
2003 Dec 03
2
COnfiguring an * system for a non-profit organization
Hi,
Maybe someone has seen this before...
I've installed a new T100P, but it doesn't seem to work. I've attached
the T100P to an Adtran 750 using a crossover cable. The Adtran shows a
red alarm on the T1 interface. The Adtran has been set to factory
defaults with FXS cards in 1-3 and an FXO card in 5.
The T100P shows no signs of life--the leds are not lit. Should I be
seeing
2004 Jul 05
2
T1 configuration, getting help via IRC?
In my * server I have a T100P, connected with a T1 crossover cable to an
Adtran TA750 with 2 FXO cards. After I do 'modprobe wct1xxp;ztcfg' the
alarm on the card starts blinking red. Running zttool confirmed that
yes, it is a red alarm. I've read a few previous posts on this type of
setup and I'm not too much closer. What should I be checking next? A
different cable? The
2004 Aug 24
3
Asterisk with Adit 600
Hello,
I am connecting Asterisk to an Adit 600 via a T100P. Unfortunately I am not able to get any lights on the T100P and the Adit 600 only shows red. I have already modprobed the t100p.
Has anyone successfully connected these before?
I've tried both a cross-over cable and a standard cat 5 cable, but I can't seem to get them to work.
Any suggestions?
Thanks!
Craig
2004 Jul 14
0
random red alarms with t100p
I'm getting random Red Alarms with my T100P. I am using cvs zaptel from
July 13, & have tried using remove clock source & local clock source.
There doesn't seem to be any warning: every couple of days the line goes
down, & then around 5 seconds later, it comes back up.
If anyone as seen this behavior, or has any ideas about where to look,
please let me know.
Thanks,
Glen
2004 Jul 22
1
Echo Canceller Wiring (Tellabs.. HOWTO..?)
Hello,
I have been researching Echo Can's for a while now, and wanted to post
this out to the list to solicit feedback (and if my assumptions are
correct, hopefully help others out)...
If anyone out there knows anything about wiring up an Echo Can, and my
outline below is incorrect, please let the me/list know..
I have posted the Documents I received from Tellabs at:
2003 Oct 15
2
Problem with T100P card in a new chassis
Due to some failed hardware on another platform, I've had to move a
T100P card to a different chassis. After this move was completed, I
am seeing some strange results on the T100P card that do not display
to me any failure mode with which I am familiar. The card comes up,
and shows "good" carrier and status, but Asterisk refuses to bring
the D-channel up. Calls of course do
2004 Jul 02
0
TA750 + T100P configuration. flashing red alarm on t100p after running modprobe wct1xxp, ztcfg
(to mods: sorry for any extra work I've put you through. Posting from my
work account, as proper)
Hello all, I'm back. I've got that lucky feeling that this will all
work out very soon, and I hope that that is true.
The issue:
In my * server I have a t100P, connected with a T1 crossover cable to
an Adtran TA750 with 2 FXO cards. After I do 'modprobe wct1xxp;ztcfg'
the alarm
2004 Aug 31
4
T100P No D-channels
Hi
Last week I installed Asterisk (release1) with digium t100p single span T1
(wct1xxp) board on Dell GX270 pc configured for PRI. Asterisk/t100p is
currently the only user of the t1 line. All worked well for about a half a
day, PSTN to SIP phones to non-SIP IP phones etc. Alas, since then I
consistently get multitudes of blue alarms on all b-channels followed by a
loss of d-channel:
Aug 31
2004 Jun 29
2
T100P-E100P circuit board differences
Hi-
Perhaps someone with an E100P in hand can answer this:
I just received an E100P from Digium (I normally buy quad boards)
I noticed that the circuit board says "T100P" on it, and I assume that the
T100P and E100P both use the same circuit board.
Can someone please confirm that their E100P says "T100P" on the artwork?
Thanks
Scott
Scott M. Stingel
Emerging Voice
2004 Jan 11
1
possible solution to PRI T100P dropped call issue
To recap:
T100P card wouldn't sync with the telco using line side
clocking ( span=1,1,0.........)
Had to use internal clocking (span=1,0,0.......)
zttool showed Tx/Rx Levels as 0/ 1
For the grins of it I replaced the T100P card with
another newer card from inventory.
This newer card has the same rev on the ASIC / FPGA
but doesn't have any of the various jumper headers
installed
2004 Oct 06
3
T100p half-height PCI bracket
Hello,
Does anybody know of a place to get a half-height PCI slot bracket for the
Digium T100P card? I have an application to fit them in 1U cases for
small, deployable PBX's. The T100P itself is short enough to fit in a
half-height slot but I need an appropriate mounting bracket to screw it into
the case.
Thanks,
Mark Hagler
2003 Jun 05
1
T100P + Capi + Caller ID issue
Hi 2 all.
I've a nice issue my * system.
I have:
asterisk latest cvs
T100P + Zhone cb (3fxo+10fxs used)
Diva Server 4BRI running Capi
a bunch of pots and sip phones
The whole system is running good (thanks to capigod
and Bic. for the help with the Eicon Diva), but there's
a very strange issue when calls arrive on the Diva
and then bridged to the pots on the channel bank:
the voice is not
2004 Nov 29
1
New T100P Pri install suggestions?
In the next week or so, we'll be turning up a new T1 Pri from Cox Cable
in Omaha using a T100P (installed but not yet configured). While discussing
the interface parameters with a very knowledgable Cox engineer, we decided
on some of the basics including b8zs, esf, dchan=24, callerid, 5 digits
of called number forwarded to *, and switchtype=national (NI2). They
indicated their CO switch is a
2005 Jan 06
1
T100P + Adtran TSU600 + FXO and caller id problems
I have following setup
Asterisk - T100P -> Adtran TSU600 P + FXOcard -> PSTN line
When PSTN line is plugged directly in to analog X100P caller id is
received by Asterisk
but when I plug it into adtran I'm not getting caller id.
Any ideas what kind of setup Adtran TSU600 requires to pass caller id
to T100P ???
regards
m.