Displaying 20 results from an estimated 4000 matches similar to: "setup for fax machine"
2012 Jan 05
1
Where are the fax instructions?
Hello,
Trying to set up res_fax_spandsp. Based on
https://wiki.asterisk.org/wiki/display/AST/T.38+Fax+Gateway I wrote this in
my extensions.conf:
exten => 306,1,NoOp(Fax transmission)
same => n,Set(FAXOPT(gateway)=yes)
same => n,Dial(DAHDI/3) ----->FXS port to fax machine
same => n,Hangup()
Call flow Im trying to pull out is as follows:
Zoiper -->
2009 Oct 07
2
system cmd + fax line
Hi
I have a site that has asterisk install with a tdm410 one port is
connected to a pstn that is used as a backup outbound line when/if the
internet/voip is unavailable.
Currently my dial plan for this line is to ignore it, I just basically
do a
s,1,noop
s,n,wait (60)
s,n,hangup
what I would like to do is if I call from a certain number be given an
option to run some commands or for the
2016 Jan 05
3
Detected alarm on channel 3: Red Alarm
Hi everyone!
I have a Digium Card TDM410
But, it appear for me this massege
chan_dahdi.c:8061 handle_alarms: Detected alarm on channel 3: Red Alarm
But my line is ok!
But sometimes it back
sig_analog.c:3807 analog_handle_init_event: Alarm cleared on channel 2
But it again back to red alarm.
What can be happen?
My lines is all ok! But when I put on Digium Card TDM410 is very inconsistent
2008 May 20
5
Server recommendation help
I am having a issues with adding a analog card to my dell 2800. I
already have a t1 card installed and running fine but when I install the
analog card asterisk will not start (ztcfg fails). I have determined it
is because of a IRQ problem and have decided to get a new server. Can
anyone suggest a server grade setup that supports this? I would rather
not buy a machine that will be unstable. I
2012 Jun 18
1
TDM410 PTSN line setup with 1 analog phone
Hello, I have a current asterisk 1.8.13.0 asterisk-addons 1.6.24 asterisk-sounds
1.2.1 dahdi-linux-complete 2.6.1+2.6.1 libpri 1.4.12 and asterisk-gui 2.1.0.rc1
(not trying to use the gui, want to do everything by hand) with a TDM410 with
2FXO and 2FXS. I have my POTS (PTNS) line plugged into port 1 (FXO) and a
analog phone connected to port 3 (FXS). I compiled asterisk with asterisk
2009 Jun 10
3
Query about tdm410 cards
Hi
recently bought a soekris net5501 and a tdm410 to place in there.
I am having some issues attaching 12V power to the card via the molex
card - basically the box for the motherboard is too small.
I have read up about a PWR2400b and it seems to use 2wire pin, I am
guessing to connect to P8 just behind the molex connector on the tdm410.
can any one here confirm this, or have any info on the
2016 Jan 05
2
Detected alarm on channel 3: Red Alarm
Humm, if I put a filter in this lines, maybe back?
2016-01-05 12:36 GMT-02:00, Ryan, Travis <RyanT at oscarwinski.com>:
>
>> -----Original Message-----
>> From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users-
>> bounces at lists.digium.com] On Behalf Of Vitor Mazuco
>> Sent: Tuesday, January 05, 2016 9:21 AM
>> To: Asterisk Users Mailing
2008 May 05
3
TDM410P driver?
Quick and dirty question: for the TDM410P I must use the wctdm24xxp driver?
Att
Vin?cius Fontes
Desenvolvimento
Canall Tecnologia em Comunica??es Ltda.
2009 Jun 28
1
Sangoma A200
Hi
I was wondering if any one has used these cards, I am looking at this as
a replacement for the tdm410, I have some issues with installing the
tdm410 in a small case because of the power plug being at the end of the
board.
I am in australia seems like we have a different setup for out fxs
voltage, any one in oz using this card ?
Thanks
Alex
-------------- next part --------------
A non-text
2008 Sep 05
1
dahdi & tdm400p: no luck
As best i could figure it out, I've installed dahdi and rc4.
My TDM400P doesn't answer fxo or fxs.
/etc/dahdi/system.conf:
loadzone = us
defaultzone=us
fxoks=1,2
fxsks=4
/etc/asterisk/chan_dahdi.conf:
[house-phones]
context=internal ; Uses the [internal] context in extensions.conf
signalling=fxo_ks ; fxo_ks Use FXO signalling for an FXS chanel
dahdichan => 1 ;
2008 Feb 15
7
Digium stopped TDM400P production: alternatives??
Hi,
Digium stopped to produce TDM400P and the new TDM410 is too new to find
it in our shops. The only alternative available is a "fully-compatible"
Openvox product...but is it really "fully-compatible"? Any experience
about Openvox products (card and zaptel versions, etc...)?
Thank you!
Giorgio.
2004 Jul 16
1
DTMF issue --help
I'm getting down to the last of my * issues ...
After calling a bank, or cc processing center; you have to enter your
social security number, or the cc number - followed by the # key.
The lovely * voice responds "transfering" I'm sorry that was an invalade
selection. Sometimes the IVR on the other end still gets the digits and
proceeds; other times it breaks the IVR on the
2010 Sep 15
2
incoming call FXO
Hi all,
Recently I have instaled one Digium TDM410 on my Asterisk. After instaled , I can do outgoing calls but I cant receive calls. I receive the following messages:
chan_dahdi.c: Got event 2 (Ring/Answered)...[Sep 14 11:24:44] NOTICE[2654] chan_dahdi.c: Got event 18 (Ring Begin)...[Sep 14 11:24:44] WARNING[2654] pbx.c: Channel 'DAHDI/4-1' sent into invalid extension 's' in
2009 Jun 23
1
How to force TDM410 to alaw
Hi
I am having some problem forcing my tdm410 to alaw over ulaw, I have
1.6.1.0 asterisk (debian i486)
dahdi 1:2.2.0 built with the hardware echo canceller firmware
/etc/asterisk/chan_dahdi.conf
alaw=1-4
but I have this in the general section, before any channel definition
dahdi show channel 1
Default law: ulaw
even when i have a call going it is still ulaw
Thanks
Alex
2003 May 22
6
OT: BRI ISDN question
I am going to try and use a passive AVM fritz BRI card for my * setup..
Here is the thing.. I need to order my BRI from BT.. The service that looks to be the one to use is what they call ISDN 2e becasue this has the option to setup hunt groups across multiple ISDN2e lines so I could add another line later to get 4 channels..
According to the BT website in order to use the hunt grouping across
2016 May 26
3
Problems with OS X 10.11.5
Hello,
I just wanted to check in on this list and see what folks know about the
new severe performance problems with OS X 10.11.5.
There's a comment on Reddit claiming that 10.11.5 is requiring SMB signing,
but I haven't found documentation on that.
I myself saw performance on my 10 GbE go from 800 MB/s on 10.11.4 to 60
MB/s on 10.11.5. My NAS is running Samba 4.3.6 on FreeNAS, which is
2009 Apr 29
2
Something wrong with DAHDI signalling according to the CLI
I have Asterisk 1.4.24 en a Digium TDM410 with EC and with 3 FXO
modules.
When I plug one PSTN-line into a FXO-port I am able to receive calls on
this line and I can also make calls from an internal SIP-phone to the
external PSTN-network.
Still I am bothered about something that appears on the CLI when I do a
reload chan_dahdi.so :
asterisk*CLI> reload chan_dahdi.so
-- Reloading module
2010 Jul 12
6
in continuation with the earlier R puzzle
When I just run a for loop it works. But if I am going to run a for loop
every time for large vectors I might as well use C or any other language.
The reason R is powerful is becasue it can handle large vectors without each
element being manipulated? Please let me know where I am wrong.
for(i in 1:length(news1o)){
+ if(news1o[i]>s2o[i])
+ s[i]<-1
+ else
+ s[i]<--1
+ }
--
2008 Feb 07
1
OT: POTS telephone like the SPA-942?
My wife really likes the fit and feel of my SPA-942. Anyone know of a
POTS telephone with similar rugged construction?
2008 Feb 20
2
Sangoma FXO EC vs Rhino FXO EC
Hi all, I am a huge fan of Sangoma cards after having many problems with
digium cards and then switching to sangoma cards and them giving me
excellent support with excellent results.
That being said, they are also alot more money than the Rhino cards and
my friend currently has 1 digium 4 fxo card in their system and they
need to add another phone line, plus they have echo problems and quality