similar to: Adtran IP712

All, I have multiple Asterisk servers in various locations running various 1.4 and 1.6 versions (lab and production) and am having trouble with a new Aastra 6739i (3.0.1.2015) registering. Below is my request to support and they have looked it over and don't see anything wrong: Support, Can not get a 6739i to register with 3 different Asterisk servers with varying configurations/versions

>It seems that you cannot create a new /etc/resolv.conf .. Did you remove resolvconf with apt-get remove --purge resolvconf? That should have restored the static resolv.conf back. Or just make use of resolvconf, Debian/ubuntu : just correctly configure interfaces. /etc/network/interfaces auto eth0 allow-hotplug eth0 iface eth0 inet static address 10.0.0.11 netmask 255.255.255.0

Hello, I have just received Adtran TSU 600 with 24 FXS ports. I have installed sucessfuly T100P card. Adtran is connected to t100p with crossover T1 cable. On T100P card I have a green light and on Adtran I do not get any errors or alarms. But I do not get dialtone on FXS ports. Adtran is configured: For Network Timing, fxs ports ore fxs_ls on Adtran. In zaptel.conf: span=1,1,0,esf,b8zs

Rich, Thanks a bunch, totally understand now and that actually makes total sense. (no need for schematics). This also explains why I used an TA750 to go into a Nortel MICS system, using FXO and no buzz. Totally balanced load from the analog ports on the Nortel across the 5 feet of CAT5 to the FXO on the adtran. Now I need to get rid of some Adtrans --- Anyone lookin to buy? :) Thanks

I have following setup Asterisk - T100P -> Adtran TSU600 P + FXOcard -> PSTN line When PSTN line is plugged directly in to analog X100P caller id is received by Asterisk but when I plug it into adtran I'm not getting caller id. Any ideas what kind of setup Adtran TSU600 requires to pass caller id to T100P ??? regards m.

I am having a problem using the Adtran 750 FXO quad card with a Groundstart trunk line. I am able to receive calls on the trunk line, however dialing out is not working. The Adtran does not seem to be doing the signaling. Has anyone used the 750 FXO card in Groundstart mode? Any special configuration issues that I should be aware of? Syed Akbar Alico Systems Inc www.alicosystems.com Tel:

Hello. I have been going thru the wiki and asterisk related sites and have not been able to find any documentation about how to configure an Adtran TA750 channel bank. The remote disconnect supervision doesn't seem to be working, when the remote caller hangs up asterisk takes up to 30-45 seconds to hangup the call. Can somebody help? Thank's

I've never set up an mgcp device before. I have an Adtran IAD with the MGCP firmware on it. I have it configured in mgcp.conf like this: [general] port = 2427 bindaddr = 0.0.0.0 [adtran] host = 192.168.2.2 context = default canreinvite = no line => aaln/1 line => aaln/2 The device is configured like this: MGCP Configuration | Standard MGCP 0.1 / NCS 1.0 MGCP Endpoint

All, I need help. I have an (actually 2) Adtran TA750's with 8 FXO ports. I get a terrible buzz on every FXO port. If I unplug the Adtran and put an analog phone on each incoming line, I have no buzz. I also have 2 Carrier Access Access Bank I's with 12 FXO ports. When I plug the same analog lines into either one of those, no noise or buzz whatsoever. I went so far as to move the TA750

I am sending a call down a E&M wink trunk to a adtran tsu600 channelbank. The extension is setup like so... exten=>799179,1,Dial(zap/g2,20,D(9179)) exten=>799179,2,Hangup() It should Dial the Adtran and send some DTMF signals to a telephone on an fxs module in the Adtran. Asterisk is seeing the call answered when the T-1 is picked up by the Adtran not when the ringing phone is answered.

Can I configure an Adtran channel bank with a mixture of FXS and FXO cards and have them come into a single T100P T1 card? It seems like this would be a cheaper solution than trying to load a bunch of PCI cards into a PC. Also, when shopping for an Adtran (on ebay) - what do I need to watch out for as far as interfaces or capabilities to make sure that it works with a Digium card?

I believe it is not fiber, but I am not sure. I am going to take one of them home tonight and hook it to my POTS line there, which for sure is not fiber. Gregory P. Scasny Golden Technologies Inc. http://www.golden-tech.com 219-462-7200 -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of Michael Welter Sent:

People on the list tend to think you can't make many cards work on a regular desktop. If you're willing to wait a couple of week I might have an answer for you. _____ From: Robert Augustyn [mailto:augustynr@yahoo.com] Sent: Saturday, December 11, 2004 7:13 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: [Asterisk-Users] Will Adtran TSU 600 work with *?

I thought this might interest a few asterisk users. I don't use them so I have no idea about Adtran's but I know a heap of people on this list swear by them. Cheers, Dean ________________________________ From: vclass.coordinator@adtran.com [mailto:vclass.coordinator_adtran.com@mail.vresp.com] Sent: Monday, 19 September 2005 9:59 AM Subject: ADTRAN Virtual Classes: Ensuring

Hello, Did anybody successfully tried upgrade Adtran TSU 600 to firmware which is working properly with T100P and asterisk ? B.

I just wanted to ask about using Adtran boxes to support analog lines into an Asterisk box. Right now x101p's are just too sensitive to RF noise inside the PC. Going with an external chassis looks like a good, albeit expensive option. It looks like I can use the Digium T1 card into an Adtran 850. The Adtran 850 would need FXO cards. It would also need the echo cancellation module. Is

Hello Can somebody send me please config files of zaptel.conf and zapata.conf for adtran fxs ports. I cannot make it work. I do not get a dial tone on Adtran and when I am trying to call from sip i get: app_dial.c:674 dial_exec: Unable to create channel of type 'Zap' == Everyone is busy at this time There are no errors on T100P and adtran. Please help! B.

Greetings, We have An Adtran 616 Total Access device talking to a colocated Asterisk machine over MGCP. Calls placed to the phones connected to the Adtran go through as do outgoing calls from the phone (prefixed by 9), but feature access codes (*97 for voicemail, for example) and extension-to-extension calls don't work. As soon as the first digit is pressed, the user hears a busy signal.

It is possible to connect ADTRAN TSU 600 VP24 FXO 24 Port Channel Bank to Asterisk ? Somebody offered me that hardware, but I do not know if thats good hardware for Asterisk. rgs, Bartosz -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20030820/4a9e4608/attachment.htm

I have a T100P card connected to an Adtran and then a T1. I have added the following configurations to Asterisk...but, when I dial 9 and then a local phone number, it bounces between the dial tone and silence and the *error* light on the Adtran blinks. zaptel.conf span=1,0,0,esf,b8zs fxsks=1-8 loadzone=us defaultzone=us zapata.conf [channels] context=from-sip signalling=fxs_ks