similar to: Interfacing pri card to legacy pbx

Hi all, I need your lights :) There are many hardware provider for E1 cards on the market, what's your exeperience with E1 and what's the preferred provider for Asterisk out of Digium? Olivier

Here's my planed setup : PRI from telco <--> (port 1 of A104d) * (port 2 of A104d) <--> PM3 The PM3, for those who don't know is lucent's portmaster RAS dial-up router. I had setup asterisk, zaptel, libpri, wanpipe (as I have sangoma's cards). In wancfg, I have port 1 as TDM_VOICE, with hardware echo on, span 1. Port 2 is TDM_VOICE, without hw echo, Clock as

I upgraded from Tormenta2 to Sangoma A101. I followed the instructions, and installation was successful. zttool, ztcfg, all show card is installed properly. I copied the parameters from my old working zaptel.conf, zapata.conf and zapata-auto.conf. Verified on Sangoma website that these files are correct. Also configured wanpipe1.conf. But doing all this didn't start the PRI channels. It says

I am connecting to a siemens hipath 4000 with dahdi 2.1.0.4 and asterisk 1.4.23 using a Te210P card. the phone guy is saying that the lines are reporting always BUSY. however on my end the status shows OK. Anyone seen this? Is there something different about connecting PRI to siemens hipath? system.conf shows: loadzone=us defaultzone=us span=1,1,6,esf,b8zs bchan=1-5 dchan=24

Hello, I would like to convert an objects list such as objects() or ls() that outputs "a101" "a102" "a104" "a107" "a109" to read within a list statement as follows : list(a101,a102,a104,a107,a109) Thanks Tony

4 Port PRI sangoma a104 From: jg [mailto:webaccounts173 at jgoettgens.de] Sent: Wednesday, March 18, 2015 2:09 PM To: Andrew Colin; Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [asterisk-users] 4 Port PRI I have a 4 port PRI card that I need to setup each port in their own group. In chan_dahdi.conf I have the following which works for one port How do I add the rest

Hi ! We curently have a centos 5 / asterisk 1.4 server that we have some DTMF problems with. It has a Sangoma A104d card and only port one is used to connect to the PSTN. Port 2 is conencted via a cross-over cable to a RAS for modem access and port 3 is connected for data communication via PPP. Now, I want to freshen this setup to something newer. So I installed a Scientific Linux 6 server,

Hi Group, I am currently facing a dead end and any help will be much appreciated. I have an a104d installed in an asterisk box, two of which is configured on ISDN pri. One is facing pstn and the other one is facing a hipath 300e Siemens. I am getting one way audio when a local on the hipath tries to make a pstn call but no issue on incoming calls from pstn going to the hipath locals. local

I was working with the rmetrics portfolioBacktesting function and dug into the code to try to find why my formula with 113 items, i.e. A1 thru A113, was being truncated and I only get 85 items, not 113. Is it due to a string length limitation in R or is it a bug in the strsplit or gsub functions, or in my string? I'd very much appreciate any suggestions ============Input script:

Hello List! I wanted to share to everyone the following compatible connectivity products that my company installed in our Asterisk based soft switch. I already sent these to the Asterisk.org site many days ago but for some reason they still have to post it. 1. Sangoma A101 single port E1/T1/PRI Card 2. Sangoma A102 dual port E1/T1/PRI Card 3. Sangoma A104 quad port E1/T1/PRI Card 4. Sangoma

I have a system that I am trying to get a port on a Sangoma A104d card connected to an Adtran 850 with 5 FXS modules and 1 FXO module. A problem I am having is figuring out what cable should be used from the port on the Sangoma to the JP2 port on the Adtran. Tried was a cross-over T1 (1->4, 2->5, 4->1, 5->2) as well as a straight T1 (1->1, 2->2, 4->4, 5->5). Neither one

Greetings folks- I'm experiencing issues with a freshly installed box. When a call comes in via PRI (Sangoma AFT-A104), I see this in my logs: [Dec 15 14:26:10] WARNING[23546] chan_dahdi.c: Unable to enable echo cancellation on channel 12 (Invalid argument) [Dec 15 14:26:10] WARNING[23546] chan_dahdi.c: Unable to enable echo cancellation on channel 8 (Invalid argument) [Dec 15 14:26:10]

Does anyone have any experience ith configureing the sangoma A102 card for testing using a e1 cross cable i've configured and installed the cards properly even the lights on the card are green which proves that my cross cable is properly built too. my problem is with asterisk which gives me these errors PRI got event: HDLC Abort (6)on Primary D-channel of span 1 PRI got event: HDLC Bad FCS

We have been pretty much able to solve our echo problems, except for the primary mode in which we desire to operate our system. See system diagram at bottom. Prior to making adjustments to cancel echos (all echocancel=no): Call Type Result (Before) --------- --------------- CP <- LEC PRI * TDMoE * FXO -> AP

Hi, To solve echo problems, I'm considering 2 alternatives. 1> Sangoma A104d - I can't find support for asterisk 1.2.1 2> Desktop echo canceller - http://www.oriontelecom.com/echo_canceller/desktop/e1_ec_desktop.html - I want to know where to buy and price. Any suggestion is appreciated. Thanks. Jason. p.s. : asterisk cli command "reload" can change rx_gain and

Has anyone had experience with one or both of these cards? I'm in a position where I might need to recommend one over the other. I've read everything that I can find online, so now I'd like to hear of personal experiences. Everything I read on both cards is "5 stars! Awesome! It Rocks!" They both seem to have similar capabilities, similar pricing, etc. Could those of

I'm going to need to build a few Asterisk boxes that have dual and quad T1 interfaces. I knew Digium made T1 interface cards and on this list I heard about Sangoma so I did a quick search and found the hardware page at voip-info.org which lists several manufactures I didn't know about. All that leads to this question: I'll be using T1s in the USA. What experiences have you all had

Good day all Is there someone that's got asterisk working well with a A101/E1 card Apparently they don't have RBS support? Please advice Thanks Altus

I have installed Asterisk on a CentOS4 box and then installed Asterisk from CVS. I installed a Sangoma A101 and connected it to a Adtran 600 using a T1 Crossover cable. The 600 has 12 x FXS, 12 x FXO interfaces. I ran through the wanpipe install instructions and configured it, now I can run [root@altpbx asterisk]# wanrouter hwprobe ------------------------------- | Wanpipe Hardware Probe Info

Hi all, I've done this a few times with other PBX's but swyx has stumped me! I'm having some trouble getting Asterisk connected to a Swyx system using a sangoma A104dx... currently the setup is: BT <-> Swyx The above setup works fine... what i'm trying to achieve is BT & SIP Trunks <-> Asterisk <-> Swyx I have connected to our BT (2 x ISDN30 UK) with