similar to: e911/CAMA/MF

I just set up a t1 with 2 camma mf 911 trunks on it, and I am having a issue with it. We can call 911 which is routed out these new trunks, and it goes to the 911 center, but they are not getting the ANI and hence "no record found". Our LEC is Embarq, and they say they can see the call come in and send: KP-911-ST and then KP-0-911-ST rather then KP-0-ANI-ST I turned on all the debug

Maybe of you guys know the answer to this: We have T1's that come from both MCI and Global Crossing as channelized (24 Ports per T) with inband (DTMF) delivery of ANI and DNIS (format = *DNIS*ANI*). My old equipment was set for D4, AMI, SF and Wink Start and so is Asterisk. I've moved these T's to Asterisk TE410P and inbound calls are arriving to external voice mail system

Maybe of you guys know the answer to this: We have T1's that come from both MCI and Global Crossing as channelized (24 Ports per T) with inband (DTMF) delivery of ANI and DNIS (format = *DNIS*ANI*). My old equipment was set for D4, AMI, SF and Wink Start and so is Asterisk. I've moved these T's to Asterisk TE410P and inbound calls are arriving to external voice mail system correctly

Hi all, I'm trying to get a handoff between me and a carrier going using Asterisk. I need to handoff using CAMA signaling. On a Cisco, you can see the configuration types that I'm referring to on this site as an example: http://www.cisco.com/en/US/products/hw/routers/ps221/prod_configuration_guide09186a008019b16e.html#35393 The example of the interaction is the following: CLEC end

Hi all, I am trying to setup a ZAP interface to do MF signaling for a handoff to a 911 tandem. The signaling I need to perform on the T1 is this: 9-1-1 Tandem: Wink CLEC end office: KP (Keypulse) NPA ST (Start) 9-1-1 Tandem: Wink CLEC end office: KP I (Info Digit) NXX XXXX ST As I'm not as familiar with the Zaptel configurabliity, I'm not really sure how to do this. Do I dial twice

Hi, We've got a dedicated T1 with two trunks running into our ILECs selective router for 911. Split out of the T1 into two MF CAMA trunks on ILEC side. I'm trying to use asterisks e911 signaling, but I'm having trouble with the dial command. (== Everyone is busy/congested at this time (1:1/0/0)) I'm missing something and I'm thinking it has to do with the hookstate

I could only get *ANI*DNIS* working one way and that was setting my signalling type on the Asterisk side to 'featd' The Definity won't send *ANI*DNIS* information back to the asterisk as far as I can tell. Other than that, I've been running it with wink/wink E&M for a while now. TN464 circuit pack on the definity side, te110p on the asterisk side. Just a crossover cable

Maybe one of you can help me with this: We have T1's that come from both MCI and Global Crossing as uses channelized (24 Ports per T) with inband (DTMF) ANI and DNIS delivery (format = *DNIS*ANI*). My old equipment was set for D4, AMI, SF and Wink Start and so is Asterisk Server. I've moved these T's to Asterisk TE410P and inbound calls are arriving to external voice mail

I currrently have Asterisk 1.2.8 with a TE110P Zaptel card tied to our Nortal DMS-10 switch via T1. This T1 trunk is configured for Feature Group D MF. The purpose of this is for LD delivery to a VoIP LD provider as a LD choice for our customers off of the DMS-10. When I sieze a channel on the zaptel, I get a spill of digits from the switch that is the called number, and I can see that in

Ok, I'm about to take the plunge, and am trying to decide between Channelized T1 E&M and PRI. I'm getting an "Integrated T1" which will have data and voice capability, all plugged directly into my digium single T1 card. In either case the data piece looks pretty straighforward, just setup the channel properly, hand it off to the linux hdlc layer, and route away.... the

Hi all, I'm sure something similar has been discussed, but one can only wade through the archives for so long. I'm setting up a T1 and my telco has a bunch of questions it wants me to answer. I know much of the TE110p is configurable to do any of this, but I wanted to know if there is an optimal or preferred setup. Any help would be appreciated. Here is the quiz my telco is giving me:

I'm trying to get this zap dial to work. I want to send DNIS and ANI to other system (ZAP/g2) at answer, while the caller hears ring (RBT). I hear the RBT, but callerid and exten is not sent to other T1 - The ZAP/g2 T1 is standard D4, SF, E&M Wink Start. - At ZAP/g2 wink, asterisk should send DTMF "*ANI*DNIS*" exten => _XXXX,1,NoOp,${CALLERID} exten =>

Hi all, I'm sure something similar has been discussed, but one can only wade through the archives for so long. I'm setting up a T1 and my telco has a bunch of questions it wants me to answer. I know much of the TE110p is configurable to do any of this, but I wanted to know if there is an optimal or preferred setup. Any help would be appreciated. Here is the quiz my telco is giving me:

Hi All, I have just migrated from Asterisk 1.0.0 to Asterisk 1.0.5 and I have an X100P installed. The old asterisk was working, but now the new version isn't picking up any calls! However, I did notice that after installation, I performed modprobe zaptel and modprobe wcfxo and they worked fine, but when I executed ztcfg, I get the following errors: ioctl(ZT_LOADZONE) failed: Invalid

Hello! We are using the Digium 405PP card, and getting the following messages: Jun 16 16:16:17 NOTICE[81926]: chan_zap.c:6832 pri_dchannel: PRI got event: 6 on Primary D-channel of span 1 Jun 16 16:16:17 NOTICE[81926]: chan_zap.c:6832 pri_dchannel: PRI got event: 8 on Primary D-channel of span 1 My config file is below. We are trying to set up D-Channel on channel 24, 1-23 in trunk group 1,

Hi, Did anyone manage to connect either Digium or Sangoma T1 card to any other PBX/gateway using T1 E&M Wink/Wink signaling? I'm trying to connect Avaya Definity to an Asterisk box with T100P and so far no luck. (I know I can do so with ISDN PRI, but need an additional ISDN processor card for Definity.) I tried to connect Definity to Cisco 3640 CCME (call manager express) to test the link

HI, I have been pulling my hair out trying to get a Cisco MC3810 to interface my Asterisk box with a T1. I am able to make outgoing calls but incoing calls never reach my Asterisk box. The cisco give a fast busy when I try to call one of the DID's. When playing around with the dial-peers I can get the cisco to pick up the call, but then it forwards the call back to the ANI that is dialing.

Due to time constraints, I'm looking to pay someone (by paypal) for a working or/almost-working asterisk skeleton of the examples listed below... SYSTEM INFO: ---------------------------------------------------------------- I will have a single channelized T1 with all lines being available for dialing in, using E&M wink, with ANI2*ANI*DNID being sent to me (as DTMF tones I guess?). I

I have a bit of a weird problem that I'm having great trouble debugging. I have a TDM400P PCI card with two FXO and two FXS modules. Both FXO modules are connected to BT lines here in the UK. Both BT lines have V23 Caller-ID, which works fine with Asterisk. Both asterisk and zaptel are fresh from CVS. Both FXO modules (channels 3 and 4) are in "group 1" for outgoing calls. My

I have what my SBC/ATT representative calls a "Supertrunk," but he can't tell me the specifics I need to know to configure Asterisk to work with it. By fiddling about, I've come up with the "almost working" configuration below. This works except that it takes about 4 seconds from when the console says the line is answered until it plays my prompt. Watching the