similar to: Card loading order...

I have an Asterisk server that was running fine until Sunday. Monday there was a power outage and the server was off most of the day. This server has a TE110P, two TDM04B and an Astribank 32. Today I noticed that the TE110P started having IRQ missess. Before today it only had about two or three per month. Today, this is the miss count after ten minutes on: IRQ Misses: 1443

I have a customer running Asterisk 1.2.13 with Zaptel 1.2.11 that is having calls dropped. Sometimes you can stay on the phone for a long time and sometimes the call is dropped within a minute. There are 9 lines connected to 3 TDM04B cards. The Panasonic Pbx we replaced did not have this problem. There are 8 SIP phones and 16 analog phones connected to two Astribank-8 units and everyone

I am having a problem with and Asterisk installation where two ports connected to a TDM400 card will have a very loud noise when you try to dial. The server has an OpenVox D110P, a TDM04B and a Xorcom Astribank 8 fxs. It is running Zaptel 1.4.11 and Asterisk 1.4.18. The problem always happens with two ports (34 and 35) which are connected to two GSM gateways. They will work fine for a week

Hi people, I would like to read your suggestions as to where the issue might be. ATA286=Grandstream Budgetone ATA 286 in SIP mode. One Lan Port and one FXS port. TDM04B= 4 FXO signal fxls There is a 8FXO-to-SIP unit in this scenario that works perfectly so i will not make mention of it. PSTN----VOIPprovider---Internet---ATA286------tdm04b---Asterisk1.2.-13 Asterisk is being used as a meetme

Hello Everyone, I checked with zttool that sometimes after the machine boots the order of the boards is changed like this: ??? Alarms Span ??? OK Digium Wildcard TE110P T1/E1 Card 0 ??? OK Digium Wildcard TE110P

I have an Asterisk 1.2.16 server running CentOS 4.4 with a TE110P card and an OpenVox A1200P card. Up to today everything was working perfectly. The OpenVox card has 8 FXS and 2 FXO ports. The two faxo ports are used for a GSM adapter and for an ATA connected to Vonage. The problem we started noticing today was that the Vonage line will receive a call and then cannot connect to any of the SIP

Running Asterisk 1.2.9. I just installed a TE110P card and configured zaptel.conf & zapata.conf. The config files look right to me but I'm getting the following error when trying to start asterisk: Asterisk died with code 1. Automatically restarting Asterisk. Does anyone have any idea what is wrong with this configuration?? Thanks in advance!!! Here's my config files: zaptel.conf

Hi, Some weird problem (or I'm too sleepy) happens with a tdm04B revision G (4fxo) Steps: modprobe zaptel modprobe wctdm ztcfg -vv /etc/zaptel.conf fxsls=1-4 # TDM04B defaultzone=us loadzone=us /etc/asterisk/zapata.conf signalling=fxs_ls group=1 context=incoming channel => 1-4 modprobe zaptel and wctdm load fine, however ztcfg -vv shows: 0 channels configured Im using centos 4.4 with

I have an Asterisk box running Fedora Core 4, Asterisk 1.4, Lippri, 1.4, and Zaptel 1.4 The Digium cards installed are TDM2400 and TE110P. Everything was working fine until I upgraded to zaptel 1.2.12 from 1.2.9 Now when I run ztcfg I get the following error message: (CAS signalling on span 2 conflicts with Clear channel on channel 40) --NOTE: signaling was spelled wrong in the error

//////////////////////////////////////////////////////////////////// Hello to all, I have a question. I am installing te110p, when I give ztcfg him - v leaves the following error to me ZT_CHANCONFIG failed on channel 25: No such device or address (6) - That means east error? - It is a physical damage of the card? Thank you very much

I have a customer running Asterisk 1.2.13, Zaptel 1.2.11 with a TE110P, a TDM04B and an Astribank-32. They have been complaining that there is echo on calls even when they are IP to IP on the same network. There are 18 Aastra 9133i phones and 30 analog phones connected to the Astribank. I can understand there being a bit of echo on the analog phones, but I do not understand why there would be

I have a X100P and a TE110P in my Asterisk box. I can either get the X100P or the TE110P to work, but never both. Here's my zaptel.conf span=1,0,0,d4,ami e&m=1-24 fxsls=25 When I load wcte11xp and wcfxo, I will get this error. [root at asterix etc]# modprobe wcte11xp ZT_CHANCONFIG failed on channel 25: No such device or address (6) /lib/modules/2.4.20-8/misc/wcte11xp.o: post-install

Hi Carlos/All, Thanks for your reply. I can remove dchan=16 from zaptel.conf But according to the documentation of Digium and sangoma they mentioning to use dchan=16. Are there any specific reason you have experiance regarding this and I am confusing that what this is included to the documentations. Regards, Vidura. On Wed, 2007-09-05 at 20:26 +0530, Vidura Senadeera wrote: > Dear All,

Dear users. My current setup uses a euroISDN E1 with 8 cahnnels for incoming and outgoing calls from a digium te110p. Currently all phones use SIP. However, I need to add some faxes lines and some POS credit card machines. These will require POTS lines with a fixed DDI. I have purchased the tdm400p and 4 FXS modules. My problem is with the zaptel.conf and zapata.conf. I am a little confused as

Hello: Have a TE110P laying around and decided to see if I could build a router around it. I've tried compiling several versions of zaptel .1.4.x with the same results. I checked the zaptel changelog and can't find anything about it no longer being supported (or that it ever was for that matter). ztcfg: Zaptel Configuration SPAN 1: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1)

Hi all, I have a Wildcard TE110P connected to a E1 line an I want to reserve channels in the following way: channels 1-15 and 17-21 for incoming calls channels 22-28 for outgoing calls channels 29-31 for emergency calls My zaptel.conf looks like this: ; incoming group = 1 signalling=pri_cpe context=from-zaptel channel => 1-15 channel => 17-21 ; outgoing group = 2 signalling=pri_cpe

Hello I have upgraded our asterisk box from zaptel to dhadi two weeks ago... Since, there has been quite a significant amount of echo when making a call. Only for the local outgoing call, the person on the other side doesn't hear any echo. This is with a TE-110P ISDN PRI card .. I've pretty much took the original zaptel configuration and used it as-is with the dahdi one ; to no

I had a working Asterisk 1.4.24.1 installation on SUSE 9 Linux but SIP only. I then downloaded and installed latest Zaptel and could not get Zaptel working. So I downloaded Asterisk again and re-installed. But still problems: Here is my ztcfg output: asterisk:/etc/asterisk # ztcfg -vvvvv Notice: Configuration file is /etc/zaptel.conf line 4: Unable to read Zaptel version information. Zaptel

Sorry I should have stated that I've tried +x, -x, x.y and x and I still get the same. Regards Lee -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Eric "ManxPower" Wieling Sent: 05 January 2007 08:10 To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [asterisk-users]

hi every body; i installed zaptel 1.4,libpri 1.4, asterisk 1.4, asterisk-addons 1.4 succefuly, but i can't find the command "genzaptelconf, so i tink to install "handy zaptel toolset" please can someone tell me whitch package goes with zaptel 1.4, i consult "http://updates.xorcom.com/rapid/pool/main/z/zaptel/" but ????????????