similar to: Bip viol. in E1 cards

I'm not 'overly' new to asterisk, but I am very new to the Digium card / Telco aspect of it. I was able to get a TE110p card, installed.. and hooked a t1 up to it. I'm using zttool to just look at 'some' output. Here is what it looks like when I just load it up: Current Alarms: No alarms. ? ? ? ? Sync Source:

Hello everyone, I bought 2 HFC-ISDN Cards and want to run the first card in NT-Mode an the second one in TE-Mode. Everything looks ok under SuSE 9.1, but I can't dial out. I removed one card, for testing purposes and want to run this one card in TE-Mode. I only want to make a call with my Grandstream BT-101 over Asterisk via ISDN. When I try to make a call I get: ---------------------

Hi, I have been trying to get a Wildcard TE122 card running here the last couple of days. libpri and zaptel are all installed and configured to E1 specs. The jumper on the card is on, so configured for E1 (I'm in Norway). When running zttool, I get 'Alarms: RED' on the single card installed. Other information in zttool: Current alarms: Red Alarm Sync source: Internally clocked

Hi, I am trying to fit the following model: sr.reg.s4.nore <- survreg(Surv(age_sym4,sym4), as.factor(lifedxm), data=bip.surv) Where age_sym4 is the age that a subject develops clinical thought problems; sym4 is whether they develop clinical thoughts problems (0 or 1); and lifedxm is mother's diagnosis: BIPOLAR, MAJOR DEPRESSION, or CONTROL. I am interested in whether or not

Hi On an old IBM Netvista thinclient, the TDM card doesn't detect incoming calls, although the card seems to be detected, and correctly configured: pbx asterisk # lspci 00:03.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface # cat /etc/zaptel.conf fxsks=1 loadzone=fr defaultzone=fr # ztcfg -vv Zaptel Configuration ====================== Channel map: Channel

Greetings and I thank you in-advance, I have a system installed with both Trixbox 1.x and 2.x installed and I am trying to utilize a wildcard x100p but it does seem hang-up or release the line. I understand that the Wildcards are not recommended, but I need to get a test system up for evaluation. Here are the steps followed: Run genzaptelconf and red alarm appears in zttool Run again and it

Hi, I have problem with X100P clone card.I can not force it to work under Asterisk 1.4.27.1 and DAHDI Version: 2.2.0.2. I looked over and over on configuration and could not see any mistakes. Here are relevant configuration files. /etc/dahdi/system.conf > fxsks=1 > echocanceller=mg2,1 > loadzone = hu > defaultzone = hu > dahdi_tool > OK Wildcard X100P

Hi Group, I have a problem with my FXO interface. It seems that asterisk cannot see any configured channels, only pseudo. Pls see the error and my config below. Rgrds Markus ----- May 2 15:09:00 NOTICE[17327]: app_dial.c:1010 dial_exec_full: Unable to create channel of type 'Zap' (cause 0 - Unknown) == Everyone is busy/congested at this time (1:0/0/1) == Auto fallthrough, channel

Hi, I am running a Cox Mixed Effects Hazard model using the library coxme. I am trying to model time to onset (age_sym1) of thought problems (e.g. hearing voices) (sym1). As I have siblings in my dataset, I have decided to account for this by including a random effect for family (famid). My covariate of interest is Mother's diagnosis where a 0 is bipolar, 1 is control, and 2 is major

Hi, I have a working Asterisk 1.2 server on kernel 2.6.22 with the OSLEC echo canceller on a Digium PRI card. I recently switched to kernel 2.6.23 with the MG2 echo canceller (nothing else changed). Each time I try to establish a call on the PRI line I get a congestion signal. in /var/log/asterisk/full: Feb 20 08:09:43 VERBOSE[10657] logger.c: -- Executing

Hi All, We are just starting to deploy a new PRI IVR system, and the incoming calls sometimes get random short 'bips' while navigating our IVR menu. Any hint on what this can be? Best regards, PauloHM

I was hoping I could get some help with an import question. I work with remote sensing imagery which commonly comes in binary form in various interleaving formats (byte interleaved by line, by pixel, etc..). These files are 2d spatial x B bands in size, and I want to be able to extract the band values from various pixels (so each line of data into R would be one pixel x B bands). What's the

At the same site, DTMF recognition is functioning badly, sometimes duplicating digits and sometimes totally missing others. We have checked already /proc/interrups, there is no interrupt being shared. Our zaptel has .. span=1,1,0,ccs,hdb3 On zapata we have ... switchtype=euroisdn signalling=pri_cpe relaxdtmf=no (yes doesn't seem to help) -----Original Message----- From:

I need some help getting a system running for one of my company's plants. I am running AsteriskNow 1.7 with Asterisk 1.6.2.10 and FreePBX 2.8.0.2. My D-Channel keeps bouncing. The telecom tech told me he thought that I might be using the wrong sync source, and I think I might have been, but I changed DAHDI system.conf to "span=1,1,0,ESF,B8ZS" (from

Hi, It seems like my ATA is making a ringing noise... (as it used to), but now (After the upgrade from 1.0.7 to 1.2) asterisk also is either making the ringing, or passing the PRI ringing from the telco on to me. Any suggestions on how to fix this?

Just some clarification here. On Monday, June 30, 2003 12:04 AM, Steven Critchfield [SMTP:critch@basesys.com] wrote: > > As for slips and bipolar violations... > T1s are just high speed serial lines. A sleep is when you loose sync > with the far side and when you see a 1 come across the line, you may > not > know which bit it was for. A slip is when one end of the circuit is

Hi, One of my pbx's seems to be having some new issues. crackling interference on the zap channels running through the channel bank, and I noticed that these happen when I hit an "irq miss" in zttool: Current Alarms: No alarms. Sync Source: Digium Wildcard T100P T1/PRI C IRQ Misses: 82695 Bipolar Viol: 0 Tx/Rx Levels: 0/8 3 Total/Conf/Act:

Hi, I've been playing with a TE120P on Asterisk 1.4.18 with zaptel 1.4.9 and I've ran into an issue. After a call placed any DTMF tone causes the server to lock up entirely. Calls placed work just fine (except for a problem with echo cancellation). The phone registered to the server is a Linksys SPA-942. I am seeing in zttool some IRQ misses, but it never seems to go above 74 (below).

Greetings, I have a quad port Tormenta 2 PCI card (uses the tor2 driver), which I have been successfully using for some time on an older, power-hungry Intel machine. I recently moved it to a newer machine with an Intel Atom D510 CPU in an effort to save on energy costs, but I cannot seem to get it to work there. Both machines are running Ubuntu 13.10 x64, with DAHDI support coming from the

Hi, On my system I've got : CLI> dahdi show status Description Alarms IRQ bpviol CRC4 Fra Codi Options LBO B4XXP (PCI) Card 0 Span 1 OK 0 0 0 CCS AMI YEL 0 db (CSU)/0-133 feet (DSX-1) B4XXP (PCI) Card 0 Span 2 OK 0 0 0 CCS AMI YEL 0 db (CSU)/0-133 feet (DSX-1) B4XXP (PCI)