similar to: discrepancy between CDR clid and Polycom IP601 clid

Make sure you set nat=yes for the sip user. Asterisk will then send replies back to the source IP address, rather than what's in the Via: header. > -----Original Message----- > From: Warren (mailing lists) [mailto:warren-lists@icruise.com] > Sent: Friday, October 27, 2006 5:45 AM > To: Asterisk Users Mailing List - Non-Commercial Discussion > Subject: [asterisk-users] Taking a

Are all of the sip phones in the same context? > -----Original Message----- > From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users- > bounces@lists.digium.com] On Behalf Of Robert Jenkins > Sent: Tuesday, January 16, 2007 1:44 PM > To: 'Asterisk Users Mailing List - Non-Commercial Discussion' > Subject: [asterisk-users] Polycom IP601 - some hints working,

I was reading a Polycom brochure and it appears that there is really no special receptionist console and the console is basically a IP601. Is this correct? The only difference is to purchase an expansion module in order to have more shortcut keys for the girls. So, apart from the hardware, as far as the dialplan is concerned, do I just treat the receptionist console as any other extension? Are

One more Polycom IP601 question please (sorry for the long intro here to document) ... In order to closely approximate the behavior of the previous telephone system that many of the users are familiar with, I have set up call parking like this: - features.conf [general] section contains: parkext => ** ; What extension to dial to park parkpos => 10-11 ; What

Hello people, I am having difficulties figuring out the POE power draw in watts from a Polycom IP601. I want to know how many IP601's can be powered from the Cisco Catalyst 3560G-48PS. The IP601 wallwart has: Input 120VAC 60hz 19W, Output 24VDC 500mA. I assume the output is appropriate value to figure out how many phones can be powered. The Cisco 3560 datasheet says "the 48-port PoE

Hi everyone, I have a user that needs a little extra volume on his Polycom IP 601 phone set for all calls (beyond what the volume control currently offers). Is there a provisioning setting for this anywhere? (I'd like to avoid a separate amplifier between the phone and handset if possible.) Alternatively, is there a way to have Asterisk 1.4.x boost the volume to a particular SIP device

Hi Polycom experts, I'm having a problem getting changes to the Polycom IP 601's (mac)-directory.xml file to update the button list on the phone. If the phone is newly provisioned (i.e. if I "Format File System" on the phone) then the new list will show up on the buttons, but of course this is pretty drastic way to do it. - Environment: Asterisk test setup with 7 phones,

Hey list, Im in this HUGE crisis. Im trying to get a Polycom 601 with two expansion modules to work. I need the XML config files I guess. Does anyone have these I can have? Im trying to get this phone up and running, and haveing MUCHO problems, can someone help me out!! Im sure if I see the configs I can see how it works, just need those XML files!! The ones from the 501 that I have dont seem to

Hey everyone, I haven't seen an issue quite like mine, so I am hoping anyone who used the Polycom 601's may have an idea. We are going to be switching our office over to Asterisk. All the phones are going to be 601's, I am going to set up a boot server, but for now I am just going to test everything on one phone. My question is I have the phone registered in Asterisk (phone icon

Hi, This used to work fine in 1.4: exten => 2131/,1,NoOp(reject3: ${CALLERID(num)}) exten => 2131/,n,Playback(no_unknow_callerid_here) exten => 2131/,n,Hangup And now, after upgrading to 1.6.1.x it matches every callerid. Did something change? Thanks,

I wanted to see if anyone has set up a large amount of out bound only voip channels? We run analog autodialers connected to analog to voip gateways (dialogic boards to audiocodes mp-124's) Bandwidth and routing is being provided by a bonded t-1 (3 meg) cisco 2600 with 2 t1 cards and a 16 port netgear switch. My question ( if you can picture the setup) is if anyone can see a

I'm having a problem with polycom ip601. If I Dial() directly eg Dial(SIP/4000) it works perfectly. The polycom rings, and stops ringing as soon as I hang up. But if the phone is called via a queue, the polycom continues to ring long after I've hung up. Other phones in the queue (grandstream, cisco) don't have this problem, and stop ringing properly when I hang up. polycom bug

Hi, I have an Asterisk 1.8.2.3 installed (public IP) with a peer (Polycom IP601) installed behind NAT. When the peer makes a call, it's working without any problem. But when a call is coming back, it ends up with a Got SIP response 400 "Bad Request" back from xx.xx.xx.xx where the xx.xx.xx.xx is the public IP of the peer. And the call drops to the voicemail (congestion at peer

How do you disable call waiting on Polycom IP601 phones? I've looked through the user and admin guides and can't see anything about disabling it. -Dan

Calling all Polycom gurus: I am using Polycom IP601 phones with Asterisk 1.4.21.2 In all Polycom phones, I set the following in sip.cfg. <dialplan dialplan.impossibleMatchHandling="2"> </dialplan> (I leave the digitmap unchanged because I thought setting impossibleMatchHandling will ignore the bitmap) ...so that I could dial any number by entering a variable-size

What hardphones support xml/html/xhmtl/microbrowser? I need an inexpensive SIP hardphone that can run simple applications (queue status, etc). The phones I know of: Aastra 480i, 9112i, 9133i (though limited by 3 LCD lines on the 91xx seems kind of silly) Cisco 79xx Mitel 5235 Polycom IP601 Any others? -Dan

Hello, If properly configured, does Asterisk 1.2 'push' SIP NOTIFY messages to registered SIP phones to indicate new voicemail? I've noticed that Asterisk only sends NOTIFY messages when my phones periodically (re-) register with Asterisk---rather than immediately after a new voicemail arrives. Hence, the MWI on my phones only update when they re-register with Asterisk, which means

I am trying to find out if Polycom (I am using IP601) can display the speed dial list using last name first instead of first name first. Currently, the speed dial list displays first name first. Thanks.

Where's the setting for overlap dialing with Polycom IP601? -Dan

Hi, I found your post on http://threebit.net/mail-archive/asterisk-users/msg04580.html I am having the exact same issue with the Polycom IP601 (SIP version 1.6.6.0036) with Asterisk 1.2.7.1. I was wondering if you found any solution to it. I would really appreciate if you could share your solution. Thanks, Khairul. BELOW, THIS WAS YOUR POST Polycom IP 601 Buddy Watch problems