similar to: beta4: outgoing call causes Red Alarm on TDM400P

Hi All, For the most part, the PBX works as it should. Occasionally people complain that they call and the PBX doesn't pick up. Other times it looks like the call is answered by Asterisk but I still hear ringing and I start listening to the IVR menu a few seconds into it. As for Asterisk not picking up, I see the following in the logs: [Mar 27 13:32:29] NOTICE[13197]: chan_zap.c:7071

Using asterisk 1.4.18 and zaptel 1.4.9 on x86_64, I am having trouble dialing out to the pstn. The call is initiated at Zap/1-1 and should exit via Zap/3. I get the following: -- Starting simple switch on 'Zap/1-1' -- Executing [2111 at internal:1] Dial("Zap/1-1", "Zap/3/8801234") in new stack [Feb 25 02:36:59] DEBUG[7194]: chan_zap.c:1954 zt_call: Dialing

Hello all, I got a problem at an asterisk server, with dropping calls, losing all channels and reaktivating all channels and beeing back up. This problem seems to occure randomly over the whole day, when it gots traffic on the card. After looking @ google I found several hints but none did work fine. To avoid problems with the phone line (german E1) I called the provider, he did a 45 min. route

Calling from PSTN let extension 601 ring twice, hang up and starts over again to ring twice, ... If I pickup I do not hear on extension 601, and on the PSTN it is still signaling to ring. Can anybody enlighten me, please? extension.conf [incoming_88097074] exten => s,1,Wait(1) ;wait to get caller ID in. exten => s,2,Dial(SIP/102,20) exten => s,3,Voicemail(u102) exten =>

Hi all, I've been running Asterisk with a TDM400P for about 6months, no problems. 2 in/outgoing analog lines, one analog phone. Recently I was messing with the XTEN client, got to finagling with things, and not knowing what was wrong I upgraded from 1.0.7 to 1.0.9 (both asterisk + zaptel). I was testing various things, and found everything worked except outgoing calls. So I checked

Scenario, I got some very good help earlier from Joseph getting me up and started but I have a couple of small problems still. Setup: FC2 Asterisk 1.0 Zaptel 1.0, TMP400P, FXS Port 1 FXO Port 4 Analog dialout line and Analog handset plugged in. Problems: 1. Incoming calls work and the phone rings and can be answered no problems, (although I wouldn't mind being able to adjust the ring but

HI I have two servers both of which get this message on one of the lines. Ring/Off-hook in strange state 6. The one server seems to be ok with it, but the other one when an extension picks up there is no one there and the incoming call keeps ringing. I tried to adjust the levels in wcfxo.c like someone had suggested, but it didn't do anything. I also upgraded zaptel to the latest. 1.2.18 and

Greetings. I am attempting to configure a system based on Asterisk 1.2.3 to be used as a backup should our aging voice mail/auto attendant system fail, which seems increasingly likely given its advanced years. The first part of this task is getting the auto attendant feature to work correctly, which I would have figured to be relatively easy. I have successfully built a menu structure, but cannot

Hello, I have recently purchased a TDM400P card with one FXO expansion card, and I'm having problems. The card does not pick up incoming calls. Asterisk detects the ringing line and rings various SIP phones as required. When a sip phone answers, the sip user hears nothing and the PSTN user continues to hear ringing. Here is the asterisk output for an incoming call:

Hi all, I have hit a wall configuring a TDM400, I have set these up before without issue but today I just can't seem to figure out what I am doing wrong. On an incoming call the following is produced in the Asterisk console with verbose 4 -- Starting simple switch on 'Zap/2-1' Mar 22 16:12:34 NOTICE[2051]: chan_zap.c:6063 ss_thread: Got event 18 (Ring Begin)... Mar 22

Hi, I'm having problems using a TDM400P Card. I put my SIM card in a Nokia Premicell and connected it to a TDM400P card but when I make calls to the number, it hangs up automatically. The card also can't call out. Any ideas? I've searched the archives without much success. I appreciate all your help. Details: I'm using Asterisk 1.2.17 on Fedora Core release 5 (Bordeaux). On an

Hello - I have a Premisys Slimline Channel Bank connected to a Digium TE110P. I am not able to call the FXS extensions or get dialtone on them. The channel bank is connected via a T1 crossover to the cable and lights show green. I really need to get this functioning by end of day. If anyone can help me out I would be greatly appreciative. Thanks, Dave zaptel.conf loadzone =

Anybody else get theses warning? [Jun 26 10:08:55] WARNING[3158]: chan_zap.c:4747 zt_handle_event: Ring/Off-hook in strange state 6 on channel 1 PB

Hi... I have the next problem.. I have a FXO card with i can make calls but i cant recive calls. At the consol, i get the next error: -- Zap/2-1 is ringing -- Zap/2-1 is ringing -- Zap/2-1 answered Zap/1-1 -- Attempting native bridge of Zap/1-1 and Zap/2-1 WARNING[262160]: File chan_zap.c, Line 2857 (zt_handle_event): Ring/Off-hook in strange state 6 on channel

Hi all, I must admit that I am stuck. I have a TDM400P card with two FXS and two FXO modules which I had set up and configured so that it was working beautifully. The only problem was that occasionally it would get itself into a state where outgoing calls would simply be met with a very loud static. A reboot would fix this issue and everything would work fine for a while. Recently however,

Well, I got my nice new 4 port FXS card this afternoon, and with all my other asterisk problems, decided now was a good time to throw it in.... So far, I have dropped it in, done a clean cvs checkout on zapata, zaptel, asterisk, make clean and make install on each. I can load the wcfxs module which finds the card (though one time it failed the register check and locked the machine up, a hard

Seems to have struck a small problem.. Using a t100p & Zhone channel bank.... one extension ringing another.....the following will appear WARNING[18448]: File chan_zap.c, Line 2685 (zt_handle_event): Didn't finish Caller-ID spill. Cancelling. if we are using defaultzone=au change it to us and the problem goes away..... any possible solutions ?? Gary .

Hi everyone, I have a PRI conection on an * system running Asterisk 1.0.9, libpri 1.0.9 and zaptel 1.0.9.2 connected to an AXE 10 (APZ 21220 System 64) in the network side. I know the system and the wildcard I´m using are ok because I´ve used them before with other PRI connections (to a Siemens EWSD) without any problem. First the PRI didn´t work (I got the TE110P alarmed with red). After

I have an issue getting any incomming calls When the phone rings something picks up and gives it a fast busy. There is no one using Zap/2 it does the same thing with voicemail and voicemail 2 you can see the console output below, I would love any help anyone could shead on this issue, Michael NOTICE[1192484144]: File chan_zap.c, Line 4270 (ss_thread): Got event 2 (Ring/Answered)... --

Today is the first time I've had any show stopping errors with asterisk since I started using it over 8 months ago... While I wait on the telco to check the circuit I thought I would post this here. Not sure yet but I thinks my 4-port PRI card is gone!!! I made a call and right when the person answered - BOOM. This is only a little better than it not working at all.