similar to: [Asterisk 1.2 + TDM FXO] Incoming call not detected

I'm not 'overly' new to asterisk, but I am very new to the Digium card / Telco aspect of it. I was able to get a TE110p card, installed.. and hooked a t1 up to it. I'm using zttool to just look at 'some' output. Here is what it looks like when I just load it up: Current Alarms: No alarms. ? ? ? ? Sync Source:

Hi all.. I`m with a problem in some E1 cards. The value of Bipolar Viol is too big, and some times the link seems well, but isn`t work correctly, like as if the link is down. Normally, I use to stop asterisk, remove the modules from my card, use modprove to set up they again, and start asterisk, and it come to work, but in some times I have to reboot the server, and then the value of

Hello everyone, I bought 2 HFC-ISDN Cards and want to run the first card in NT-Mode an the second one in TE-Mode. Everything looks ok under SuSE 9.1, but I can't dial out. I removed one card, for testing purposes and want to run this one card in TE-Mode. I only want to make a call with my Grandstream BT-101 over Asterisk via ISDN. When I try to make a call I get: ---------------------

Hi, I have been trying to get a Wildcard TE122 card running here the last couple of days. libpri and zaptel are all installed and configured to E1 specs. The jumper on the card is on, so configured for E1 (I'm in Norway). When running zttool, I get 'Alarms: RED' on the single card installed. Other information in zttool: Current alarms: Red Alarm Sync source: Internally clocked

Greetings and I thank you in-advance, I have a system installed with both Trixbox 1.x and 2.x installed and I am trying to utilize a wildcard x100p but it does seem hang-up or release the line. I understand that the Wildcards are not recommended, but I need to get a test system up for evaluation. Here are the steps followed: Run genzaptelconf and red alarm appears in zttool Run again and it

Hi, I've been playing with a TE120P on Asterisk 1.4.18 with zaptel 1.4.9 and I've ran into an issue. After a call placed any DTMF tone causes the server to lock up entirely. Calls placed work just fine (except for a problem with echo cancellation). The phone registered to the server is a Linksys SPA-942. I am seeing in zttool some IRQ misses, but it never seems to go above 74 (below).

Hi Group, I have a problem with my FXO interface. It seems that asterisk cannot see any configured channels, only pseudo. Pls see the error and my config below. Rgrds Markus ----- May 2 15:09:00 NOTICE[17327]: app_dial.c:1010 dial_exec_full: Unable to create channel of type 'Zap' (cause 0 - Unknown) == Everyone is busy/congested at this time (1:0/0/1) == Auto fallthrough, channel

Hi, I have problem with X100P clone card.I can not force it to work under Asterisk 1.4.27.1 and DAHDI Version: 2.2.0.2. I looked over and over on configuration and could not see any mistakes. Here are relevant configuration files. /etc/dahdi/system.conf > fxsks=1 > echocanceller=mg2,1 > loadzone = hu > defaultzone = hu > dahdi_tool > OK Wildcard X100P

Hi, One of my pbx's seems to be having some new issues. crackling interference on the zap channels running through the channel bank, and I noticed that these happen when I hit an "irq miss" in zttool: Current Alarms: No alarms. Sync Source: Digium Wildcard T100P T1/PRI C IRQ Misses: 82695 Bipolar Viol: 0 Tx/Rx Levels: 0/8 3 Total/Conf/Act:

Helo, I have problem with Digium TE110P connected to CISCO 3640 (port on NM-HDV-2E1-60) wth PRI E1 link. I use CISCO now for testing but when I tried with real PBX problem was exactly same. I have this messages in Asterisk conole and log sometimes: NOTICE[1115] chan_zap.c: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 Usually 2-5 such messages in series, can be repeated after 10

I need some help getting a system running for one of my company's plants. I am running AsteriskNow 1.7 with Asterisk 1.6.2.10 and FreePBX 2.8.0.2. My D-Channel keeps bouncing. The telecom tech told me he thought that I might be using the wrong sync source, and I think I might have been, but I changed DAHDI system.conf to "span=1,1,0,ESF,B8ZS" (from

Hi, I have a working Asterisk 1.2 server on kernel 2.6.22 with the OSLEC echo canceller on a Digium PRI card. I recently switched to kernel 2.6.23 with the MG2 echo canceller (nothing else changed). Each time I try to establish a call on the PRI line I get a congestion signal. in /var/log/asterisk/full: Feb 20 08:09:43 VERBOSE[10657] logger.c: -- Executing

Hello Since TDM cards are known for being particular when it comes to motherboards (PCI 2.2, etc.), I was wondering if there is a utility that can check that the Zaptel driver works OK and can tell if the TDM card is compatible? That way, if an FXO module is not reporting an incoming call, we'd know it's because of the Zaptel driver, and not something elsewhere. Are "dmesg",

A bit about my experience with the TDM-04 FXO. Only saw a few post on this subject, thought I would contribute a little about my experience to save others the hassle. a. As an earlier poster noted, the driver for the FXO is in the wcfxs module. Perhaps it should be renamed to something less confusing. b. You need the zaptel,zapata libraries from the cvs, the ones with Asterisk 0.7.2 won't

Just some clarification here. On Monday, June 30, 2003 12:04 AM, Steven Critchfield [SMTP:critch@basesys.com] wrote: > > As for slips and bipolar violations... > T1s are just high speed serial lines. A sleep is when you loose sync > with the far side and when you see a 1 come across the line, you may > not > know which bit it was for. A slip is when one end of the circuit is

I just needed to test a dialup modem connection (don't ask) and I had a modem connected to a TDM card (FXS port) which then dialled out via a E1 PRI on a TE4xxp card. See my log below: atdt0198xxxxxx CONNECT 36000 V42bis ** Dial IP ** Username: xxxx Password: Entering PPP Session. IP address is xxx.xxx.xxx.xxx MTU is 1500. OK ATH0 OK ATDT0198xxxxxx CONNECT 31200 V42bis ** Dial

Hi, I'm trying to configure a clone of X100 for use with asterisk, but i have reached the zaptel.conf step and have not been able to progress further as i'm getting the following error: arnor:~# ztcfg -v Zaptel Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) 1 channels configured. ZT_CHANCONFIG failed on channel 1: Invalid

I am trying to get to the bottom of audio clicks, pops, dropouts with my Asterisk server. These occur even when the system is under minimal load (e.g. 1 Zap device in a queue being played music on hold) and occurs with both Zap and Sip devices so isn't network related. The audio problems occur at the same time on all channels and seems to be when Asterisk "gets busy" and uses

Hi guys, now that violations.d/logcheck is empty, violations.ignore.d/logcheck-* are useless and many messages that were previously elevated and filtered there now turn up as system events. Thus, I went ahead and merged violations.ignore.d/logcheck-* into ignore.d.*/* in the viol-merge branch. http://git.debian.org/?p=logcheck/logcheck.git;a=shortlog;h=refs/heads/viol-merge Unless I hear

Ok so I read the Linux 2.6 related README and finally compiled propperly, I thought but at the end I notice that lscpi does report the cards, but I cant modprobe wcfxo nor zaptel and I do have wcfxo.ko in the /lib/modules/2.6.8/extra/ directory, so what gives? This is a Debian Sarge, thanks! # # make clean starts here # make[1]: Entering directory `/usr/src/zaptel-1.4.0/menuselect' rm