similar to: Zap with SIP

Deat all, I am in middle of integrate Asterisk with Toshiba astrata legacy pbx. Following is my setup *Asterisk <-> Digium TE110P <-> E1 card in toshiba pbx <-> Toshiba PBX* A =============================================> B C <============================================ D Asterisk PBX and strata PBX connected using back to back E1 cross cable. Physicall connectivity

Hello Folks, I'm trying to decide here between a few cards for connecting an Asterisk box to a single E1 channel (either PRI or R2 signaling): - Digium E100P: has been replaced by the TE110P below, but can still be had at places like digitnetworks.com for $475, and I guess there's always a place for good-olde-obsolete cards in the world as long as they work :-) - Digium TE110P:

I have a strange problem: if I put on hold an incoming call from my Digium TE110P, I can't resume it and the person at the phone continues to hear MOH until the line falls. My TE110P is connected with an italian E1 NT. If I put on hold a call on a SIP channel I can resume it without any problems. Is there someone that can help me? These are my configurations: zaptel.conf

Hello, I am trying to get a Wildcard TE110P to work in a relatively modern HP Proliant DL385p Gen8 server. Being a potent 12 core Opteron server I expected no problems. Much to my dismay the dahdi_test results are constantly terrible: # dahdi_test Opened pseudo dahdi interface, measuring accuracy... 89.101% 89.195% 89.142% 88.957% 88.953% 89.115% 89.089% 89.134% 89.066% 89.021% 88.933% 89.044%

Hi, This error I got it just when I gonfigure zaptel support isdneuro 31 channels. But if I configure zaptel to support T1 and just 24 channels I have no problem. ######################################################################## #### # # Zaptel Configuration File # # This file is parsed by the Zaptel Configurator, ztcfg # # loadzone = it span=1,1,0,ccs,hdb3,crc4 bchan=1-23 dchan=16

Hello Everyone, I checked with zttool that sometimes after the machine boots the order of the boards is changed like this: ??? Alarms Span ??? OK Digium Wildcard TE110P T1/E1 Card 0 ??? OK Digium Wildcard TE110P

Fedora Core 6 regards, Pablo. On Thu, Mar 08, 2007 at 05:01:15PM -0800, Jose Bertuzzi wrote: > Hello Everyone, I checked with zttool that sometimes after the machine boots the order of the boards is changed like this: > ??? Alarms Span ??? OK Digium

Hi, We have integrated an Asterisk system (built from CVS HEAD) with an Avaya IP Office switch running Q.SIG on an E1 interface, using a Digium Wildcard TE110P. The system is being used for handling both inbound and outbound call traffic to a set of Asterisk agents who are connected via extensions on the IP Office - there is a maximum of 15 agents at any one time, allowing at least another

> > > Hi, > > > I checked by changing to from-zaptel, but no luck yet. Pls guide me on > this. > > Regards, > vudura senadeera > > > ------------------------------ > > > > Message: 9 > > Date: Fri, 19 Jan 2007 16:47:18 -0000 > > From: "Robert Jenkins" < raj@jrw.co.uk> > > Subject: RE: [asterisk-users]

Hi, I configured an asterisk box with 1 Digium Wildcard TE110P T1/E1 Card 0 I setup the jumper in e1 position. my zaptel.conf : defaultzone=it loadzone=it #gestione PRI span=1,0,0,ccs,hdb3,crc4,yellow bchan=1-15 # set this to 1-15,17-31 for E1 dchan=16 # set this to 16 for E1 bchan=17-31 # set this to 1-15,17-31 for E1 # Asterisk starts correctly, I see th 30 channels. Anyway I cannot put

As these problems are very time sensitive and frustrating, I suggest you document each change you make and do them one at a time so you can actually know what the problem was and not introduce new problems in the process. Find someone who is on the phone quite a bit and will give you an honest evaluation of the call dropping situation (unless you yourself are experiencing this issue too).

Hi, I have to link an Asterisk Box with a PBX Matra 6501. System look like this : E1------Te110P Asterisk Te110P-----E1----Matra 6501-----Phones | | Ip Phones Incoming call from E1 will enter on asterisk, if incoming number is _800n then go to IP phones. In this case no problem. But if it's an another call i want to return call to my

We i have settup it like this it giveme caller id agent id and date-time on gsm file but i want them to be in folder on every day basis datewise. exten => _1NXXNXXXXXX,2,Set(CALLFILENAME=${ACCOUNTCODE}-${EXTEN}-${TIMESTAMP}) exten => _1NXXNXXXXXX,3,Monitor(gsm,/rec/asterisk/apr07/${CALLFILENAME},mb) Any Idea ? Faisal > ------------------------------ > > Message: 16 >

Hi all, I?ve ran into a problem regarding D-channels. I have setup Asterisk (CVS-HEAD-03/21/05-16:41:57) on RH Fedora Core 3(2.6.10-1.770_FC3) I also have a digium wcte11xp card for connetivity to the PSTN(E1). When I start zttool i see that Current Alarms changes between Recovering and Blue Alarm/Recovering. I started to see these problems after i moved the digiumcard from one PCI slot to

Hi. I'm looking at ordering a 30-channel ISDN connection from telia (a swedish operator) and then using a Wildcard TE110P card with that and asterisk to do IVR. Can I be certain that the TE110P card will work with that ISDN connection? A 30 channel ISDN certainly sounds like an E1 connection, but I couldn't get any clear answers from the operator if it is. Has anyone used the TE110P

Hi everyone I have a Digium card TE110P and after plug it, turn on the computer and configure, the LEDs don't light up in spite of what Digium FAQ says about the LEDs: When will the LED's light up on my TDM400P/TE110P/TE2XXP/TE4XXP? ... The TE110P LED's will light up RED when the span is configured and kernel module is loaded. If configured correctly and a circuit or channel bank is

Before studying your configs, what have you tried so far? Did you change this? Also, try changing your second span timing from span=2,2,0,ccs,hdb3,crc4 to span=2,0,0,ccs,hdb3,crc4. Here is the documentation on voip-info for why it may be the cause of your issues http://www.voip-info.org/wiki/view/Zaptel.conf+span+syntax span definition format:

These allow and disallow work with NuFone for me disallow=all allow=ulaw allow=alaw allow=gsm Jeff Message: 11 Date: Fri, 11 Mar 2005 11:15:51 +0100 From: "Edward Banfa" <edward@radform.com> Subject: [Asterisk-Users] NuFone Configuration [problem] To: "'Asterisk Users Mailing List - Non-Commercial Discussion'" <asterisk-users@lists.digium.com>

Hi All I have a TE110P card connected to a PRI line. In my zaptel.conf I have: span=1,1,0,esf,b8zs bchan=1-23 dchan=24 loadzone = us defaultzone=us and my zapata.conf is: [channels] context=inbound-pri switchtype = national pridialplan=unknown ;pridialplan=international signalling = pri_cpe callerid=asreceived busydetect=no usecallerid=yes hidecallerid=no callwaiting=no callwaitingcallerid=no

Hi All, I have a TE110P in E1 mode, in a dell poweredge 250. The 30 channel E1 supplied is from a telco in Australia, with the following in my zaptel.conf: span=1,1,0,ccs,hdb3 bchan=1-15 dchan=16 bchan=17-31 (yes the provider has NOcrc4 for some reason) After installing the latest cvs libpri and zaptel, I successfully loaded the kernel modules. The card is verified as not sharing an