similar to: Digium E1 and Digium TDM400P (2xFXO) Help!

Hello, I am having a lot of trouble with my deployment of Asterisk. I am running the PBX-In-a-flash turnkey of Asterisk and ever since deployment I have had many different problems. I have managed to get all issues sorted out as I go along, until this one that randomly began last week. We are using Grandstream GXP 2000 Handsets in the office, and at TE110P card to interface to our ISDN OnRamp10

thankyou both very much for your swift responses and helpful insight... While my knowledge of administrating Asterisk is fairly decent, i must say my knowledgebase and ability in troubleshooting it is fairly lousy... all these wonderful suggestions you have had about turning this log on here, etc sounds great, but i don't know where to begin on that! how do you recommend i turn these on or

Hello, I have some problem to start asterisk. First I have followed a lot of tutorials to complete correctly the install process. Now it works when I type zttool I can see when I am or not connected to the PSTN. But, I run asterisk with vvvv verbose and I can't see the call detection. There is no detection of the call. I have a X100P card FXO with only one line. So only one channel I

lo there all, i recently upgraded to ubuntu 7 (fiesty fawn) and am having a problem with the install procedure for the zaptel modules. i did the make ; make install and it appeared to go ok, the wctdm module is in the list of lsmod after boot. so is the zaptel module. however when i do an asterisk -vvvv it gives me problem about chan_zap not being able to load. i googled and found some

Hi, I bought a Digium Quad E1 card model TE406P. Till now, I can't make it work... I mean, I have red alarm when I configure one E1. The provider is in France (France T?l?com) and I use the following zaptel config : span=1,1,0,ccs,hdb3,crc4 bchan=1-15,17-31 dchan=16 I'm using Linux 2.6.15 and when I run ztcfg -vvvv, it seems that all channels are configured... So can someone

hi, all I have configure tdm400p analog fxo card. that's ok. but how to chek that is working properly or not. i chek with ztcfg -vvvv and zttool . that's ok. i want to dial from my fxo port to another extesion. zaptel.conf ------------------ fxsls=1,2,3,4 defaultzone=in loadzone=in zapata.conf ---------------- context=mycontext signalling=fxl_ls group=1 channel=1-4 thanks' in

Hi i have buy a Digium TDM400P with 1 fxo modules TDM01B for connect my asterisk to a french analog line. In my zaptel.conf, i have: loadzone=fr defaultzone=fr fxols=3 when i load the module, i have in logs: Nov 24 06:13:40 gw kernel: Freed a Wildcard Nov 24 06:13:40 gw kernel: Zapata Telephony Interface Unloaded Nov 24 06:13:40 gw zaptel: Removing zaptel module: succeeded Nov 24

Sorry about last posting, typo... I just added 2 Digium X100P cards. When my * box boots, it found them and configured them. When I enter genzaptelconf, it comes back with the following error: line 13: Unable to open master device '/dev/zap/ctl' Unloading zaptel hardware drivers: Removing zaptel module: rmmod: module zaptel is not loaded

hi every body; i installed zaptel 1.4,libpri 1.4, asterisk 1.4, asterisk-addons 1.4 succefuly, but i can't find the command "genzaptelconf, so i tink to install "handy zaptel toolset" please can someone tell me whitch package goes with zaptel 1.4, i consult "http://updates.xorcom.com/rapid/pool/main/z/zaptel/" but ????????????

Hi when I turn on my PC I able to load the drivers and start my card, if I reboot the PC I have the following error ztcfg -vvv Zaptel Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) Channel 02: FXS Kewlstart (Default) (Slaves: 02) Channel 03: FXS Kewlstart (Default) (Slaves: 03) Channel 04: FXS Kewlstart (Default) (Slaves: 04) 4 channels

Dear users. My current setup uses a euroISDN E1 with 8 cahnnels for incoming and outgoing calls from a digium te110p. Currently all phones use SIP. However, I need to add some faxes lines and some POS credit card machines. These will require POTS lines with a fixed DDI. I have purchased the tdm400p and 4 FXS modules. My problem is with the zaptel.conf and zapata.conf. I am a little confused as

I had a working Asterisk 1.4.24.1 installation on SUSE 9 Linux but SIP only. I then downloaded and installed latest Zaptel and could not get Zaptel working. So I downloaded Asterisk again and re-installed. But still problems: Here is my ztcfg output: asterisk:/etc/asterisk # ztcfg -vvvvv Notice: Configuration file is /etc/zaptel.conf line 4: Unable to read Zaptel version information. Zaptel

This is a new installation. Here are the specs of my system: Linux asterisk 2.6.21.5-smp #2 SMP Tue Jun 19 14:58:11 CDT 2007 i686 Intel(R) Xeon(R) CPU E5420 @ 2.50GHz GenuineIntel GNU/Linux 08:08.0 Ethernet controller: Digium, Inc. Unknown device 8000 (rev 11) (ethernet?? first time with a card like that for me) dmesg Zapata Telephony Interface Registered on major 196 Zaptel Version:

I have an Asterisk@Home 1.3 server (Asterisk 1.0.9) and recently added a TDM400P with (1) FXO card on port 4. Inbound calls are always successful but outbound calls fail 75% of the time with intercept messages from my dial tone provider that include "we're sorry, your call did not go through", and "we're sorry, when placing a local call it is now necessary to dial an area

Hi, I have installed Asterisk 1.4.20 on Debian Etch. The server has no telephony card installed, but I have anyhow installed Zaptel (Zaptel-1.4.9) in order to be able to use MeetMe. The Zaptel modules load normally. I obtain the following prompts: kerplunk:/# /etc/init.d/zaptel start Loading zaptel framework: done. Waiting for zap to come online...OK Loading zaptel hardware modules: ztdummy.

Hi Version 0.9.0 of Xorcom Rapid Debian/GNU/Linux/Asterisk has just been released. Main changes: * A decent version of Asterisk/Zaptel (1.0.2) is provided * Includes a better default configuration * Automatic detection of the most common Zaptel cards * Contains more optional software (apache, MySQL, Webmin and others) - available via menu You can get it from:

I have had a TDM400 with 2 FXO and 2 FXS working for ages (>12 months). It has stopped working. All four green lights are still lit. I have rebuilt zaptel and asterisk and restarted but the problem persists. /sbin/ztcfg -vvvv Zaptel Configuration ====================== Channel map: Channel 01: FXO Kewlstart (Default) (Slaves: 01) Channel 02: FXO Kewlstart (Default) (Slaves: 02) Channel 03:

Hi list, Attempting to get an ISDN-BRI line connected using an HFC-S PCI card together with Asterisk v1.4.14 and Zaptel 1.4.7 on a Debian etch system, I find that I can't access the card's resources because the channels are always be busy. An attempt to call out results in the following CLI output: == Primary D-Channel on span 1 down == Primary D-Channel on span 2 down

Quick and dirty question: for the TDM410P I must use the wctdm24xxp driver? Att Vin?cius Fontes Desenvolvimento Canall Tecnologia em Comunica??es Ltda.

I have one TDM2404E digium card on asterisk box, after configuring the zaptel and zapata configuration files, I am getting these errors when reloading asterisk: ast_unregister_indication_country: Removed default indication country 'us' setup_zap: Ignoring signalling setup_zap: Ignoring answeronpolarityswitch unable to recognize channel 13-5 what is the reason for that? Thanks,