similar to: asterisk 1.4.10 on linux kernel 2.6 needs timing device for trunking

I have successfully installed and configured the asterisk, the incoming and the outgoing calls are working fine, its a tremendous solution :) Now i want to enable trunking between two asterisk boxes, in the iax.conf i have put: [karachi] ... ... ... trunk=yes ... ... ... everything seems to work fine but when i load asterisk it says: -------------- Feb 17 10:59:14 WARNING[18726]:

starting 161.1-beta3: chan_iax2.c:10925 build_user: Unable to support trunking on user 'iax-out' without DAHDI timing But I have these "timing" modules: ls /usr/lib/asterisk/modules/res_tim* /usr/lib/asterisk/modules/res_timing_dahdi.so /usr/lib/asterisk/modules/res_timing_pthread.so Do I need to do some magic to get these loaded? modules.conf is set to auto. Is this what

Hi, do I have a chance to use iax trunking on OpenBSD where there is no zaptel driver or ztdummy available? Do I can use sth. else as timing source? kind regards Sebastian

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi, As I understand it, IAX2 trunking requires zaptel timing. Zaptel timing is provided by Zaptel cards, ztdummy or ztrtc. ztdummy requires usb-uhci and ztrtc can't run on smp systems. So if you only have smp systems with ohci and no zaptel cards (because it's a sip/iax2 gateway) then you're screwed? - -- Regards, Tais M. Hansen

I've read in different places that if I want to do trunking and meetme on Asterisk I need to have a reliable timer. People have recommended that I install a Digium board, even if I don't have any circuits connected to it, just to get a reliable timer. However, I've also read that if I'm using kernel 2.6, I don't need to have a Digium board. I have a few servers that

I am getting the following warnings on the CLI when loading Asterisk 1.6.1-rc1: [Feb 12 12:32:34] NOTICE[22261]: timing.c:59 ast_install_timing_functions: Multiple timing modules are loaded. You should only load one. [Feb 12 12:32:34] ERROR[22261]: codec_dahdi.c:398 find_transcoders: Failed to open /dev/dahdi/transcode: No such file or directory [Feb 12 12:32:33] WARNING[22261]:

I was wondering what could be pros and cons of ztdummy vs proper timer device (i.e. X100P). I am going to set up an asterisk server in europe (to do trunking, to save bandwith) and I was wondering if it'll be OK to get it going with ztdummy. Furthermore, I have only a 1024/256kbps PPPOE DSL link and I need to squeeze 12 channels through, I was wondering which codec would be suitable

I am trying to get a GSM gateway (Alpha Tech GSM Gateway Blue Gate Dual Band Analoog FXO) working with Asterisk. I had a working FXO configuration to a analog port of a small home 1/4 ISDN pbx. I used this same configuration to connect a GSM Gateway that is supposed to be connected to the external(FXO) analog port of a pbx. I can get my configuration to dial the mobile number via the gateway, but

Hi, I am using Debian OS kernel 2.6.22-3-amd64 and zaptel driver 1.4 with ztdummy module for meetme application. I use meetme with SIP channels. I have such problem that when one connects to the conference voice is "cut". Each voice sequence is disturbed. Does any one have similar issue and could give me some advice?? my extension.conf for meetme: ;switch =>

Hello everybody! I have some problems with my Astersk. I have an analogical OpenVox card and A Billion ISDN card (with mISDN). I load the modules with modprobe zaptel and modprobe wctdm. When I run ztcfg -vv I have this: Zaptel Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) 1 channels configured. ZT_CHANCONFIG failed on channel 1: No

Hi, >However, I believe that zaptel >= 1.4.6 or zaptel 1.2 >= 1.2.21 should >support hires timers for timing on kernel >= 2.6.22 . > >What version of Zaptel do you use? > I was using version 1.4.5.1 I just downloaded and installed version 1.4.7, configure/make/make install finished without an error, but when is used modprobe ztdummy the system said: FATAL: Error

Trouble getting chan_sip2 to compile below is what I have done -download acl.c.patch,acl.h.patch,chan2s_sip.c to /root/software cp /root/software/chan_sip2s.c /usr/src/asterisk/channels cd /usr/src/asterisk/ patch -p0 acl.c /root/software/acl.c.patch cd /usr/src/asterisk/include/asterisk patch -p0 acl.h /root/software/acl.h.patch - added the follow to /usr/src/asterisk/channels/Makefile

I am trying to set up an IAX2 trunk between two servers. Server A has the following in iax.conf: [general] ... [ServerB] type=friend trunk=yes host=dynamic secret=myPassword context=myContext Server B has the following in extensions.conf: [outgoing] exten=>_40X,1,Dial,IAX2/ServerB:myPassword@x.x.x.x/${EXTEN} I am using bmtools to monitor the bandwidth usage, and I am not seeing a difference.

Hi All I am using RHEL , kernel 2.6.9-5, asterisk 1.2.4 , zaptel 1.2.3 installed , when I give modprobe for zaptel and ztdummy , I do not any error message my iax.conf contains the entry for trunking as [hoportal] type=friend host=192.168.20.32 secret=mysecret context=local trunk=yes my extensions.conf contains the entry for trunking as exten =>

Has anyone seen this before? [root at shelob rpm]# yum update rpmdb: Program version 4.2 doesn't match environment version error: db4 error(22) from dbenv->open: Invalid argument error: cannot open Packages index using db3 - Invalid argument (22) error: cannot open Packages database in /var/lib/rpm Traceback (most recent call last): File "/usr/bin/yum", line 30, in ?

I have several servers using ztdummy as the timing source, some CentOS 4.x, some CentOS 5.x, some Asterisk 1.2.x, some Asterisk 1.4.x. "zap show status" differs between the servers: ZTDUMMY/1 (source: Linux26) 1 UNCONFIGUR 0 0 0 ZTDUMMY/1 (source: RTC) 1 UNCONFIGUR 0 0 0 ZTDUMMY/1 1 UNCONFIGUR 0

Hi all, did not find much info in lists about subj. I have ztdummy working properly because I can use conferences without any errors. But when I try to use trunk=yes, I get the following: Sep 2 21:20:51 WARNING[1137720112]: chan_iax2.c:6422 build_user: Unable to support trunking on user home' without zaptel timing Sep 2 21:20:51 WARNING[1137720112]: chan_iax2.c:6246 build_peer: Unable to

Hi! When I try to load the ztdummy driver via "insmod ztdummy", I get the following errors: /lib/modules/2.4.26/misc/ztdummy.o: unresolved symbol zt_unregister /lib/modules/2.4.26/misc/ztdummy.o: unresolved symbol zt_transmit /lib/modules/2.4.26/misc/ztdummy.o: unresolved symbol zt_receive /lib/modules/2.4.26/misc/ztdummy.o: unresolved symbol zt_register I'm using zaptel-1.0.8 and

Is ztdummy still required with Asterisk 1.4 when no zaptel cards are available to use for timing? In all the beta releases I used to get a warning when Asterisk started up, saying that no timing device was found. The warning seems to have gone away with the full release of 1.4, which prompts the question... Is it still required? Does 1.4 do something different for timing? Regards, David

I have 1 * box having x100p installed and the other has no zaptel card at all. both of the * box has compiled in ztdummy module and both have been activated by modprobe ztdummy. When using trunk to connect the 2 *box. The one without zaptel card complaint about unable to accept trunked packet: no matching peer. On the one has zaptel card I have tried to remove the ztdummy module and connect