similar to: Opinion on hardware (computer) for an Asterisk Server!

I have built Asterisk on SuSe Linux 7.3 on an Ultra 2 Sparc WorkStation. I am listing the modification I had to do for the benefit of anybody else who wants to use Asterisk This workstation is equipped with one 400 MHz RISC UltraSparc II CPU, 256 MB RAM, Two 9 GB 10,000 RPM UltraSCSI Disks. I have a gatekeeper running on this machine, I had to do the following modification to build * on Sparc:

Hi list, I've just compiled and installed Asterisk 1.4.16 and when I try to run "zap show" I get the message "*No such command 'zap show'*". I have a Sangoma Remora A400D with 2 FXS / 10 FXO ports, I've installed the latest wanpipe too. zaptel-1.4.7.1 was compiled from the wanpipe installation, so I don't know what's happening here!!! Any ideas???

Hi all, Space is starting to get a bit tight here, so I''m looking at adding a couple of TB to my home server. I''m considering external USB or FireWire attached drive enclosures. Cost is a real issue, but I also want the data to be managed by ZFS--so enclosures without a JBOD option have been disgarded (i.e., I don''t want to use any internal HW RAID controllers). One

Client - Not for Profit in the Middle of the Jungle/Rain Forrest Infrastructure - Datacenter is Non Climate Controlled, Prone to Flooding, and has Sketchy Power, LAN - NEW Cabling in main Office building, Hodge Podge of DYI wiring across remaining buildings. Phones - Total of about 50 extensions. Only about 25 - 30 phones will be IP phones, 20-30 more will have to be analog due to the distance.

Hi list, I'm having problems transferring certain calls made by the attendant between the PSTN and to an internal extension. Although, transfers between the majority of the calls ends successfully. Debugin this, I've found that calls made to certain "numbers" (Telephony Providers), aren't detected as ANSWERED in the CDR, so they are not properly accounted (for billing),

supervision. Verify if for those "numbers" the CO revert the line polarity when callee answer. callprogress=no is a good test too. Jorge Ra??l G??mez C. wrote: > Hi list, > > I'm having problems transferring certain calls made by the attendant > between the PSTN and to an internal extension. Although, transfers > between the majority of the calls ends successfully.

Hi list, I'm wondering if it's possible to transfer a call that is still ringing??? Actually, the problem is that my telco provider doesn't offer an uniform method for answer/disconnection supervision, and by that I mean, some of it's line (I think) offer a polarity reversal, but other lines (of the same service provider) do not offer anything at all, so the answer of a call

I have been working with SYSLINUX/PXELINUX Mostly v.2.x recently v3.0 &v3.1 to remote-boot IBM PC's off of 1.44Floppy Images with great success. I have searched through several distributions and the SYSLINUX package seems to be by far the easiest to work with.. (thanks) My question would be: Is it possible to boot a diskless client PC with Complete hard disk images? or even better hard

Hello. I've developed an algorithm in R which I need to package. The implementation uses S4 objects and it's divided in 5 files. Everything is working fine when I load the files into the R console but when I try to make a package I get an error that I don't quite understand. Here's what I do: *1.* in R console, I do and get: > package.skeleton(name='remora') Creating

Hi, How can can you stack sangoma cards such as http://www.sangoma.com/datasheets/p_a200-specs in a given PC enclosure ? It seems to me that it introduces mechanical constraints that seem difficult to comply with as space between cards is set by Remora expansion card. Your advice ? Cheers -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hello, I'm preparing a setup before installing it within the next few days. In this setup, I'm using a SPA112 as an ATA for an analog phone. The target phone is a Gigaset A400 DECT handset. In my lab, I've got another A400 handset and an old Matracom 46 handset. When I connect my Matracom 46 handset to my SPA112, I can send and receive calls. When I connect my A400 handset to the

Hello I have an office with a T1 that provides 4 (out of 8) analog PSTN lines thru an adtran board. I want to add 4 more analog lines. Currently I have a Digium TDM40B. I'm wondering what the best upgrade path is, where I define 'best' as the solution that is most likely to work without problems (like interupt conflicts) and work with my current echo tuning . I see my purchase

Hi, I have A101DE Sangoma Card( http://www.sangoma.com/products/hardware_products/digital_voice_and_data_networking/a101.html ) lspci shows as 03:04.0 Network controller: Sangoma Technologies Corp. A200/Remora FXO/FXS Analog AFT card [root at asterisk ~]# lspci -vvv -s 03:04.0 03:04.0 Network controller: Sangoma Technologies Corp. A200/Remora FXO/FXS Analog AFT card Subsystem: Unknown device

Hi I have been having a rough time getting a Sangoma A200/Remora FXO/ FXS Analog AFT card set up properly. The main issue is that the card has four ports and as far as I can tell Asterisk is only seeing two. On the two that it recognizes the "Green" FXS ports are not green, they just are not lit. The "RED" FXO ports are indeed red, but from what I have read your not

Hi - I just got a Sangoma A200 card with a single 2FXO module and what appears to be an empty module. I put the card in my Dell GX260, but the power light on the front of the box just blinks and won't power up. I did take the power cable from the CDROM to put on the card - I don't need the CDROM right now.. I'm looking for direction in getting this card working - I currently

I'm a long time user of Digium carts and stupid me i wanted to give Sangoma a try. We got Sangoma A400 with 6 FXO ports. Asterisk version: 1.4.35 Zaptel version: 1.4.11 Wanpipe version: 3.5.11 we tried to use fxtune but looks like it wont work with Sangoma card, ( please correct me if i'm wrong) Echo is really bad and also we have background noise on all lines. We tried both mg2 and

Hello All, I am trying to figure out which way to go for a quad port fxo solution with a good echo can on it. My options are the sangoma remora, a mediatrix fxo, or something similar. The issue is that I would need a good EC. This would be on about a 9000 foot loop, and the lines don't function well on a spa-3000 or zaptel tdm 4 port card. Anyone have experience that drives them in a

I'm having (I think) timing issues in relation to bridged T1-T1 calls via dynamic spans. Fax calls are intermittently working, but voice is fine. My box has a Sangoma A400 inside it as the primary Zaptel timing source. My T1 PRIs that are hooked to the box come in via a foneBRIDGE2 (dynamic TDMoE spans). PRI #1 is the telco and PRI #2 is an existing Comdial FX-II. For some reason, bridged TDM

I have a RoR app that currently uses file_column for image upload and display. The app is part of a website that uses CPG for running a photo gallery, and I''d like to know if anyone has interfaced a RoR app to CPG by any chance. I want to dump file_column and let CPG handle my images. -- Posted via http://www.ruby-forum.com/.

Hello Chris, On Thu, 01 Feb 2018 17:00:03 +0000 Chris Murphy <lists at colorremedies.com> wrote: > You can to use efibootmgr for this. NVRAM boot entry is what changed, not > the contents of the EFI System partition. > > efibootmgr -v > > Will list all entries and Boot Order. You need to use --bootorder to make > sure the CentOS entry is first. Interesting.. thanks