similar to: TDM400P not answering or making calls

hi, i have problem with pass-through faxing with this scenario hylafax(iaxmodem) - iax - asterisk1 1.2.22 - sip - asterisk2 1.2.X(xen virtual) - linksys ATA i can fax to fax2mail on hylafax but after upgrade asterisk2 to 1.4 faxing is not working hylafax(iaxmodem) - iax - asterisk1 1.2.22 - sip - asterisk2 1.4.X(xen virtual) - linksys ATA configuration is same do you hava any idea what is

I'm testing a TDM400P with FXO module to receive incoming calls from an analogue line and send it to a SIP device. To recieve callerid, I need to use cidsignalling=dtmf and cidstart=polarity. The problem is that when a call is finished, the TDM400P seems to require about 20 seconds to prepare for the next incoming call. If a new call comes in within 20 seconds after the previous call was

The REV I card shows up in the PCI table as: 02:05.0 Network controller: Tiger Jet Network Inc. Intel 537 (or 02:05.0 Class 0280: e159:0001) Subsystem: Unknown device b119:0001 But the REV E/F shows up as: 02:0d.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface (or 02:0d.0 Class 0780: e159:0001) Subsystem: Unknown device b100:0003 One

Can anyone suggest where I might begin looking for an answer please? I have just installed a TDM400P (2x FXS and 1x FXO modules installed) The first problem is that it does not seem to be able to detect if the remote party has hung up when a call comes through on the FXO. For example, if someone calls in, and then hangs up at any time after it starts ringing, Asterisk carries on as though the

No matter what I do, I've tried now three different motherboards, my TDM400P keeps giving 'Freshmaker failed register test' after emitting a list of xx != 00 errors. Anyone have any clues for me? I'm wondering if I got a bad module or what. TIA -- Undocumented Features quote of the moment... "It's not the one bullet with your name on it that you have to worry about;

Greetings all, I'm new to asterisk... Finally got two IP phones and two TDM400P's (one with four FXO modules and one with four FXS modules)... Began experimenting a couple days ago and have ran into a very aggrevating problem. My system consists of the following hardware: Abit BL7-RAID motherboard Pentium 4 1.6GHz processor 512MB SDRAM 2 TDM400P cards 2 3Com 3c905

Hi , I have an asterix (1.2.7.1) box with 3 TDM400P and 10 FXO modules, and zaptel (1.2.5). The problem is that 6 modules can't be initaized and i get the folowing error: May 7 09:17:37 WARNING[7739] chan_zap.c: Unable to specify channel 9: No such device May 7 09:17:37 ERROR[7739] chan_zap.c: Unable to open channel 9: No such device here = 0, tmp->channel = 9, channel = 9 ztcfg output

Hi, We have two of these 4 port FXO cards. However, we are having some problems with incoming/outgoing calls. The latest version of Asterisk/zaptel from CVS is being used. Voicemail, internal SIP <-> SIP calls between Pingtel xpressa hard phones work terrific, echotest is fine, and so on. The zaptel and wcfxs modules load fine, and show all 8 FXO interfaces in dmesg:

Hi, I have received a new card TDM400P revision E, from digium. When I tried to modprobe wcfxs it gave me the following errors: Freshmaker version: 63 Freshmaker passed register test ProSLIC on module 0 insane (1) 255 should be 2 Module 0: Not installed ProSLIC on module 1 insane (1) 255 should be 2 Module 1: Not installed ProSLIC on module 2 insane (1) 255 should be 2 Module 2: Not installed

Has anyone got a sensible zaptel.conf and zapata.conf for 2 TDM400P's working with UK set-up. They're set-up with 7 analogue phones and 1 PSTN port. Currently zaptel.conf has fxoks=1-7 fxsks=8 loadzone=uk defaultzone=uk It's really zapata.conf that would be useful. Currently using the zaptel/asterisk that comes with Ubuntu (latest) which needed a bit of tweaking (1.2.16), but could

I'm having real problems with my connection to BT, it is a home line, but after a while it sets an alarm and only a restart of asterisk resets it could some one look at the below configs and suggest any changes to make this more reliable Thanks for your help Robb asterisk version 1.6.1.10 dahdi version SVN-trunk-r7445 dahdi_scan active=yes alarms=OK description=Wildcard TDM400P REV I

I installed the TDM400P and installed it on a system running on Fedora Core1, please refer to the steps below. I connected an analogue phone to the FXS port. When I pick up the speaker I don't hear the dialtone although when I press a number key I hear a DTMF generated. What could be the problem? I appreciate your help 1- First I installed the TDM400P in the PCI slot and connected

Hi all, I'm trying to install a TDM400P card, and I need some help. Please, see below... after dmesg command: [root@voip root]# dmesg via82cxxx: board #1 at 0xD800, IRQ 5 Zapata Telephony Interface Registered on major 196 PCI: Found IRQ 3 for device 00:09.0 PCI: Sharing IRQ 3 with 00:10.1 Freshmaker version: 71 Freshmaker passed register test Module 0: Installed -- AUTO FXS/DPO Module 1:

Hi i have buy a Digium TDM400P with 1 fxo modules TDM01B for connect my asterisk to a french analog line. In my zaptel.conf, i have: loadzone=fr defaultzone=fr fxols=3 when i load the module, i have in logs: Nov 24 06:13:40 gw kernel: Freed a Wildcard Nov 24 06:13:40 gw kernel: Zapata Telephony Interface Unloaded Nov 24 06:13:40 gw zaptel: Removing zaptel module: succeeded Nov 24

Hi all, I was wondering if anyone had any pointers on how to determine whether or not a module has gone wonky on the TDM400P? I have a 2 FXO (channels 3 and 4) and 2 FXS unit (channels 1 and 2). The bad (?) module in question is the FXO module on channel 3. I can't dial in to or out of that channel; dialing in gives a busy signal, dialing out just shows * hanging around after attempting a

Howdy, 1 x TDM400P card with 1 x fxo module. 1 x BT Pots line. Location - UK Calls work fine outbound but i'm unable to pickup the inbound calls. Asterisk debug: Asterisk -vvvvvvvvvvcg *CLI> -- Starting simple switch on 'Zap/1-1' -- Executing Wait("Zap/1-1", "1") in new stack -- Executing Answer("Zap/1-1", "") in new stack

Dear users. My current setup uses a euroISDN E1 with 8 cahnnels for incoming and outgoing calls from a digium te110p. Currently all phones use SIP. However, I need to add some faxes lines and some POS credit card machines. These will require POTS lines with a fixed DDI. I have purchased the tdm400p and 4 FXS modules. My problem is with the zaptel.conf and zapata.conf. I am a little confused as

I have a TDM400P with one FXO module and two FXS modules in it. I also have a Wildcard X101P. After trying hard to get things working on various Intel computers, but having echo problems that made it not really usable, I decided to try it on some older PowerPC (Macintosh) hardware running Yellow Dog Linux. Things started off smoothly. Both zaptel and asterisk seemed to compile okay, and both

I have an asterisk 1.2.9.1 machine with zaptel 1.2.6 running. On the TDM400P, I have 1 FXS port and 3 FXO ports. dmesg reveals: Zapata Telephony Interface Registered on major 196 Zaptel Version: 1.2.6 Echo Canceller: KB1 PCI: Found IRQ 10 for device 01:01.0 PCI: Sharing IRQ 10 with 01:05.0 Freshmaker version: 73 Freshmaker passed register test Module 0: Installed -- AUTO FXS/DPO Module 1:

I have a TDM21B (A new TDM20B that just arrived plus a X100M that I already had). This card sometimes works, and sometimes only the FXO module is seen. (correction to previous message that incorrectly listed X400M/S400M when I'm using only the single port versions of these modules (X100M/S110M). By "works", I mean all 3 modules have the green lights on the ports on and when