Displaying 20 results from an estimated 3000 matches similar to: "TDM400 and TDM800 fxo stop answering"
2007 Nov 02
1
AEX800 (TDM800 Express) - not detected
I have a AEX800 PCI Express card - sort of a TDM800 with PCI-Express.
(or AEX844 - 4FXS & 4FXO)
I downloaded Asterisk Now - and have got this loaded on a new
motherboard (Intel with 3 PCI, 3 PCI Express - etc).
(Downside on PCI-Express is the physical support the express slot gives
(very little) compared with an 'old' standard PCI slot!!!)
With only this card in the box....
2007 Aug 04
0
zttool says tdm800 is OK, but it won't recieve calls.
I have a TDM800 that is installed and working. (TDM800 + 2 X QUAD FXO).
Zttool says it is configured, ok, and there are no issues.
Ztcfg -vvv shows that all the channels are configured.
Zap show channels in the CLI show all 8 channels configured as they are
supposed to be.
When I plug in a pots line from the telco and make a call to that line,
asterisk does not respond. (No Starting
2007 May 28
2
Multiple TDM400p cards in one machine -- no longer an issue?
Hi all,
Years ago, I was pretty sure attempting to use two TDM400p cards in one
machine was recommended against by Digium ... probably because the cards
couldn't hack it, and/or interrupt problems etc
I have seen some posts recently that seem to indicate it is in fact possible
these days thanks to some updated firmware perhaps? ..... I just need to
have two in the server because the 4 ports
2006 Mar 21
2
TDM400 FXO module not answering or dialing out.
Hi all,
I have hit a wall configuring a TDM400, I have set these up before without
issue but today I just can't seem to figure out what I am doing wrong.
On an incoming call the following is produced in the Asterisk console with
verbose 4
-- Starting simple switch on 'Zap/2-1'
Mar 22 16:12:34 NOTICE[2051]: chan_zap.c:6063 ss_thread: Got event 18 (Ring
Begin)...
Mar 22
2007 Apr 02
1
Yeastar Cards
I am in the process of buying a TDM800 card from Yeastar (
http://www.yeastar.com/products.asp?TypeName=TDM800%20PCI%20Card&cTypeName=1 )
Any one has tested this cards? How reliable are them? I am specially interested
in the FXO/FXS module.
--
Gustavo Felisberto
(HumpBack)
Web: http://dev.gentoo.org/~humpback
Blog: http://blog.felisberto.net/
------------
It's most certainly GNU/Linux,
2009 Mar 04
1
Question on phone line "pass through"
Hi all,
I have a TDM2400 full of FXS cards and a TDM800 full of FXO cards.
If I have a fax machine on the FXS port dialing out through asterisk
on the TDM800 FXO, should I be expecting any problems?
Or should this just work as expected? (ie, flawlessly with the
asterisk box essentially transparent to the whole operation).
I am doing it this way to allow many faxes and modems to share a dial
2007 Sep 17
1
Problem with asterisk-perl-0.08 and Asterisk >= 1.2.20
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Hello,
I've been using for a long time asterisk-perl-0.08 for prepaid card
applications, and I've identified a problem with the last releases of
asterisk-1.2, installed with Trixbox.
The command get_variable() raises a signal SIGPIPE when it is called
(whatever the variable to get).
I made tests with Asterisk 1.2.20, 1.2.21 and 1.2.22, and I
2010 May 24
4
convert zaptel to dahdi?
I am trying to get a zaptel install converted to dahdi.
I can get dahdi installed, and the pseudo device even shows up; however, dahdi show channels shows me nothing. There is a TE122 and a TDM800 in there, and neither show up.
dahdi show status shows both cards, and dahdi tools show that the cards are there, working, and have no alarms.
What am I missing?
Michael Munger, dCAP, MCPS, MCNPS,
2007 May 03
3
FXO recommendation
Hi all,
With the gamut of FXO cards out there, I'm looking for a recommendation for
home use. I have a nicely working Asterisk 1.4 system that just requires an
FXO card to connect my NTL PSTN to it. My previous X101P clone seems to have
kicked the bucket.
Any suggestions would be greatly appreciated.
Regards
Kyle
--
Kyle Gordon
kyle@lodge.glasgownet.com
http://lodge.glasgownet.com
2007 Aug 22
1
Zaptel 1.2.20.1 and 1.4.5.1 released
The Asterisk.org development team has announced the release of Zaptel
versions 1.2.20.1 and 1.4.5.1. These releases are to correct an error in
the install target in the Makefile of the 1.4.5 and 1.2.20 Zaptel
releases, as well as a handful of other issues. See the respective
Changelogs for more details.
Both releases are available as a tarball as well as a patch against the
previous
2007 Aug 22
1
Zaptel 1.2.20.1 and 1.4.5.1 released
The Asterisk.org development team has announced the release of Zaptel
versions 1.2.20.1 and 1.4.5.1. These releases are to correct an error in
the install target in the Makefile of the 1.4.5 and 1.2.20 Zaptel
releases, as well as a handful of other issues. See the respective
Changelogs for more details.
Both releases are available as a tarball as well as a patch against the
previous
2005 Mar 10
1
Delay on outgoing calls
Hi, I've a wildcard TDM400P card with 2 fxo and 2 fxs modules.
I've set this extension in my extensions.conf for obtain the external
line:
exten => 0,1,Dial(Zap/g2,10)
The dial application is executed immediatly but next this there is a
delay before I can hear the tone.
This is the output in the CLI:
-- Starting simple switch on 'Zap/1-1'
-- Executing
2005 Jul 04
1
Enable verbose output for TxFax/RxFax
Hi, I'm using asterisk with a digium TDM400P: I can't send/recive faxes
with a Philips fax machine.
It seems that the fax machine doesn't recognize the carrier.
How can I see the spandsp logs? I've enabled debug on the asterisk CLI,
but I can't see any output while the txfax/rxfax application runs.
Stefano Arata.
2008 May 20
7
Busy out a zap channel?
Is there a way to busy out a Zap channel? I have a customer who is
having problems with a line connected to a TDM800 card and we would like
to busy out that line. Since that line is the head of the hunt group I
cannot simply disable that channel, I need to busy the line so calls
will come over the other lines.
--
?Telecomunicaciones Abiertas de M?xico S.A. de C.V.
Carlos Ch?vez Prats
Director
2007 Feb 04
1
TDM400 stopped bridging outgoing FXO call
My TDM400/zaptel 1.2.10/Asterisk 1.2.13 suddenly stopped bridging outgoing
FXO calls. If I make a call (from an FXS channel) to a PSTN destination,
and the other side answers, Asterisk will show continued ringback on the FXS
channel, while the PSTN side hears silence. No error message appears.
If a call from PSTN terminates on the same FXO, Asterisk can still ring the
FXS channel, and when
2004 Sep 27
3
TDM400 FXO outgoing call only
I have an analogue line connected to an FXO module on a TDM400. I want
to use the FXO line only for outgoing calls - incoming calls are
answered by other equipment, but even if I don't specify an "s"
extension, the FXO module still seizes the line for all incoming calls.
Is it possible to configure the FXO module to ignore ring events
completely? Wiki resources etc have been no
2005 Feb 17
1
TDM400 FXO not responding to inbound rings after 30ish days?
I am having an issue where my TDM400P FXO module stops acknowledging
incoming rings after running for about a month.
My system is an AMD Athlon XP 2800+ with 256MB RAM, ABIT NF7S
motherboard, Slackware (Linux 2.4.26) and Asterisk from CVS Stable (1.0).
All outbound dialing continues to work during this condition. Stopping
and restarting Asterisk does not resolve this issue. The only resolution
is
2005 Feb 17
0
TDM400 FXO not responding to inbound rings a fter 30ish days?
> Any assistance would be greatly appreciated.
If your install doesn't have to be 24/7, cron a reboot at 2 am. Since I did,
it's a nonissue for me.
2005 Feb 18
0
Monitoring a telco line for MWI through a TDM400 FXO
Folks,
I've tried to find a reference, but I've had no luck, and would
appreciate your thoughts:
I'd like to be able to monitor a telco line for Message Waiting
Notification, however I cannot figure out if this capability is
available.
Detecting either FSK or Stuttered Dial tone would serve, but I can't
find anything in the list archives or Wiki with clues as to how this
might
2007 Feb 08
1
TDM400 with 1 FXO
Hi All,
I cannot get my TDM to work correctly.
In my /etc/zaptel.conf file I have
loadzone = us
defaultzone=us
fxoks=1
In my /etc/asterisk/zapata.conf file I have
[trunkgroups]
[channels]
context=from-pstn
usecallerid=yes
hidecallerid=no
callwaiting=yes
usecallingpres=yes
callwaitingcallerid=yes
threewaycalling=yes
transfer=yes
canpark=yes
cancallforward=yes