similar to: How to stack Sangoma Remora cards

> -----Original Message----- > From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users- > bounces@lists.digium.com] On Behalf Of Lee Jenkins > Sent: Monday, May 28, 2007 8:57 PM > To: Chris Earle; Asterisk Users Mailing List - Non-Commercial Discussion > Subject: Re: [asterisk-users] Multiple TDM400p cards in one machine -- > nolonger an issue? > > Chris

Hi all, Years ago, I was pretty sure attempting to use two TDM400p cards in one machine was recommended against by Digium ... probably because the cards couldn't hack it, and/or interrupt problems etc I have seen some posts recently that seem to indicate it is in fact possible these days thanks to some updated firmware perhaps? ..... I just need to have two in the server because the 4 ports

Hi I have been having a rough time getting a Sangoma A200/Remora FXO/ FXS Analog AFT card set up properly. The main issue is that the card has four ports and as far as I can tell Asterisk is only seeing two. On the two that it recognizes the "Green" FXS ports are not green, they just are not lit. The "RED" FXO ports are indeed red, but from what I have read your not

Hi, I have A101DE Sangoma Card( http://www.sangoma.com/products/hardware_products/digital_voice_and_data_networking/a101.html ) lspci shows as 03:04.0 Network controller: Sangoma Technologies Corp. A200/Remora FXO/FXS Analog AFT card [root at asterisk ~]# lspci -vvv -s 03:04.0 03:04.0 Network controller: Sangoma Technologies Corp. A200/Remora FXO/FXS Analog AFT card Subsystem: Unknown device

Hello. I've developed an algorithm in R which I need to package. The implementation uses S4 objects and it's divided in 5 files. Everything is working fine when I load the files into the R console but when I try to make a package I get an error that I don't quite understand. Here's what I do: *1.* in R console, I do and get: > package.skeleton(name='remora') Creating

Hi - I just got a Sangoma A200 card with a single 2FXO module and what appears to be an empty module. I put the card in my Dell GX260, but the power light on the front of the box just blinks and won't power up. I did take the power cable from the CDROM to put on the card - I don't need the CDROM right now.. I'm looking for direction in getting this card working - I currently

Hi: I have a Sangoma A200 card installed in a server with two FXO modules and one FXS module. Analog sets connected to the FXS module have a "squeaky static" -- it's like static mixed with the sound of someone vigorously cleaning a window a few doors down. In other words, it's not a classic static noise, but it is noise, and it's distracting. Remote callers can hear this

Hello I have an office with a T1 that provides 4 (out of 8) analog PSTN lines thru an adtran board. I want to add 4 more analog lines. Currently I have a Digium TDM40B. I'm wondering what the best upgrade path is, where I define 'best' as the solution that is most likely to work without problems (like interupt conflicts) and work with my current echo tuning . I see my purchase

Hi, I'm trying to install asterisk(v1.2.22) with FreepBX(v2.2.3) with a 4-Port FXO Sangoma card A200. I'm using Fedora 7 (x86_64) kernel version 2.6.22.1-27.fc7, but i'm having these errors: $ ztcfg -vvvv Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) Channel 02: FXS Kewlstart (Default) (Slaves: 02) Channel 03: FXS Kewlstart (Default) (Slaves: 03) Channel 04: FXS

Hello All, I am trying to figure out which way to go for a quad port fxo solution with a good echo can on it. My options are the sangoma remora, a mediatrix fxo, or something similar. The issue is that I would need a good EC. This would be on about a 9000 foot loop, and the lines don't function well on a spa-3000 or zaptel tdm 4 port card. Anyone have experience that drives them in a

I've spent the last week or so troubleshooting echo problems at my Wife's business, and I've been able to clear up about 99% of the echo, but there is still a little residual echo that I can't seem to "tweak out". The users describe it as "buzzing or crackling", but what it sounds like to me is a slight echo, but just of one syllable of the word.

Hi list, I'm about to install Asterisk on an Old HP NetServer LC2000 Server (year 2001), it has 2 Pentium III 1GHz CPUs (Coppermine FSB 133MHz 256K L2 Cache), 768MB PC-133 ECC RAM, 3 UltraSCSI LVD2 18.2GB 10K RPM HDD in RAID5, 100Mb NIC for server. This Server will support 35 SIP phones (users) and 10 FXO ports (for telco lines) and 2 FXS ports (internal analog phones) with a Sangoma Remora

Hey Guys! We had echo issue before so we replaced old PRI card with Sangoma A102D HWEC. Now my question is i set rx/txgain level 0.0 default do i need to touch this value or default is best. I have read on google and people say it should around 14844 on ztmonitor for rx/tx level same. I just use milliwatt and test my default 0.0 rx/tx level and it come around 4600. Do you think i need to make

Hi list, I've just compiled and installed Asterisk 1.4.16 and when I try to run "zap show" I get the message "*No such command 'zap show'*". I have a Sangoma Remora A400D with 2 FXS / 10 FXO ports, I've installed the latest wanpipe too. zaptel-1.4.7.1 was compiled from the wanpipe installation, so I don't know what's happening here!!! Any ideas???

Hi all, I have a trixbox2.6.1 on my one server, i have configured sangoma A200/Remora FXO/FXS Analog AFT card on that server, from my zap line the incoming faxes are coming, i have setup the did for zap channel. my question is when i am getting any faxes, asterisk shows me rxfax execution and suddently asterisk crashes and i can't get email notification for received faxes. any one help me

I'm a long time user of Digium carts and stupid me i wanted to give Sangoma a try. We got Sangoma A400 with 6 FXO ports. Asterisk version: 1.4.35 Zaptel version: 1.4.11 Wanpipe version: 3.5.11 we tried to use fxtune but looks like it wont work with Sangoma card, ( please correct me if i'm wrong) Echo is really bad and also we have background noise on all lines. We tried both mg2 and

Hi, I have Sangoma A101DE 1 Port E1/T1 With Hardware Echo Cancellation ( PCI Express ) Card installed on the box. *Its not detected.* Details are as below :- [root at asterisk ~]# lspci 00:00.0 Host bridge: ATI Technologies Inc RS480 Host Bridge (rev 01) 00:01.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge 00:04.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge 00:05.0 PCI bridge: ATI

http://www.highpoint-tech.com/datasheets/RR2220%20datasheet_050430.pdf Anyone know if this is any good under Centos 4.3 ? I see there is a current RHEL 3 and 4 driver. Would that driver survive kernel upgrades, I'm guessing it would being modular ? (please don't tell me that 3ware is the only make to use, tw_cli is not exactly user friendly). Anyone using this -

Hello List, This is what I want to do: When a call comes in I want to ring an extension that happens to be loud speaker. The users can the press *8 to answer the call. Is there a SIP device that I can connect to Asterisk as an extension that can accomplish something like this? -------------- next part -------------- An HTML attachment was scrubbed... URL:

Has anyone used either the 8 port or 4 port FXO device from Grandstream? (GXW-4108 or 4104). They seem to be the lowest cost multi port FXO devices that I can find, so I'm getting ready to buy the 8 port version. I just want to see if there are any opinions on the device before I commit to the purchase. If people have not used the Grandstream, are there any issues with using