similar to: No subject

the CNAM info in the Q.931 call setup message. I've tried all permutations of switchtype (dms100 & national) and facilityenable that I can think of, but I still don't see CNAM coming out the other side. Telco confirms that "Name Out" is enabled on our PRI. Any pointers on what I'm missing, and/or how to debug further? zapata.conf: --- [channels] context=3Ddefault

Hi Group, I am currently facing a dead end and any help will be much appreciated. I have an a104d installed in an asterisk box, two of which is configured on ISDN pri. One is facing pstn and the other one is facing a hipath 300e Siemens. I am getting one way audio when a local on the hipath tries to make a pstn call but no issue on incoming calls from pstn going to the hipath locals. local

Hello gang, We just got MaBell to turn on our callerid. I tested the capability with a southwest bell box and a plain phone, so I know the line is sending the signal. I'm running Asterisk SVN-branch-1.4-r204834 using a TDM400P card. Here is my dahdi_cfg -vv output: dahdi_cfg -vv DAHDI Tools Version - 2.1.0.2 DAHDI Version: 2.1.0.3 Echo Canceller(s): MG2

I'm trying to upgrade from 1.4.24.1 to 1.6.0.9 with a TE120P card. I can't make any connection over the T1. From CLI: ERROR[26017]: chan_dahdi.c:14300 process_dahdi: Unknown signalling method 'pri_cpe' at line 37. cat chan_dahdi.conf cat chan_dahdi.conf [trunkgroups] [channels] language=en ;internationalprefix = 00 ;nationalprefix = 0 context=from-pstn switchtype=national

Dear Customer Support, i connected the asterisk to a e1 interface of our hipath4000. outgoing calls from a sip peer of my asterisk to an up0 telephone which iss connected to the hipath4000 are working. If you want to dial from an up0 device to the e1 interface where asterisk is connected to, you have to use the prefix 83. But when you enter the 3rd cipher this error appears at the cli

Actually I am using Asterisk 1.2.7.1, zaptel 1.2.5, libpri 1.2.2 I ve tried many values for rx/txgain togeher with echocancel and relaxdtmf. The detection is not working with call file, manager originate and not with the dial command to the mobile. I have no ideas left. I got it sometimes to work if I use a specific channel (i.e. Dial(ZAP/14/...) But with the same vaules on a second call there

Hello All I'm using asterisk 1.1.X and MFCR2 lib version 0.03pre2. when i call to E1 (connected with asterisk), chan_unicall don't detected event incoming call and show error. error messages: *CLI> Warning, flexibel rate not heavily tested! Rx CAS bits 0x9 [ 10000/ 0/ 0] Line unblocked -- R2 Channel 4 unblocked Rx CAS bits 0x9 [ 10000/ 0/ 0] Line unblocked -- R2

Hi Srs. we have to integrate a Nortel MATRA M6501-L with Asterisk with a TE410P. All call from outside get into asterisk and asterisk send to Nortel in a correct way. My problem is when a call is made from Nortel to Asterisk. If we digit a national Number in Spain([98]ZXXXXXXX or 6XXXXXXXX) all work find. But if we digit an international number call doesn't progress. I Have seen in

Hello, i have succesfullu setup asterisk with Sangoma E1 card, evrything works well but i don't know how to pass indications from telco switch to the user - when users call bad number telco switch shuld talk "unallocated number" but its only send PRI_CAUSE 1. How to pass voice indications thru asterisk to clients? My /etc/zaptel.conf: span=1,0,0,CCS,HDB3,CRC4 dchan=16

Hi All i'm using sangoma card. connected to E1, my wanpipe file as #================================================ # WANPIPE1 Configuration File #================================================ # # Date: Fri May 27 00:25:04 GMT+7 2005 # # Note: This file was generated automatically # by /usr/sbin/wancfg program. # # If you want to edit this file, it is # recommended

Hi All, I have just migrated from Asterisk 1.0.0 to Asterisk 1.0.5 and I have an X100P installed. The old asterisk was working, but now the new version isn't picking up any calls! However, I did notice that after installation, I performed modprobe zaptel and modprobe wcfxo and they worked fine, but when I executed ztcfg, I get the following errors: ioctl(ZT_LOADZONE) failed: Invalid

Hello to all, I have a problem with an asterisk qsig. I have three machines: Nortel CS1000 --- Card Sangoma PRI ---> Asterisk QSIG ---SIP Trunk---> Asterisk I use Snom phones on Asterisk. If I call from Asterisk to Nortel, Nortel reminds me of the name of the person i'm calling and I visualize on the display of Snom phone, but if I call from Nortel to Asterisk, the QSIG does not send

I have seen conflicting references in regards to the Digium Wildcard TE411P echo settings in zapata.conf. Does anyone have the official word on this? Should echo cancel be enabled in zapata.conf if the card has built in EC? If so, should a particular EC method be compiled into the zaptel build? My reference, which has echo: My zaptel is 1.2.5 context=from-pstn switchtype=national

I just managed to put in a TE410 card in an Asterisk box to work with OnRamp 20(E1 downunder). I am able to dial in but was not able to dial out. Can anyone offer me some advice please? In my extensions.conf, I just put in: [default] ... exten => 0,1,Dial(Zap/g1) and I get this on the console when I dialled 0. -- Executing [0 at default:1] Dial("SIP/5166-b76004f8",

And I'll resend this one too. Silly scalix. --Rob -----Original Message----- From: Rob Thomas Sent: Thursday, 22 June 2006 12:19 AM To: 'Asterisk Users Mailing List - Non-Commercial Discussion' Subject: RE: [Asterisk-Users] zapata.conf: recent changes? Looks like you've stopped compiling libpri. All those options that are being ignored, are being ignored because they're

I have a new Sangoma A102 and I'm trying to get it running in asterisk. A look through the dmesg log shows the card is detected and the various channels created. However, when I start asterisk I get the error below. Any ideas? My zapata.conf is below. Thanks, MD == Registered custom function SIPCHANINFO == Registered custom function CHECKSIPDOMAIN == Manager registered action

Hi I have recently upgraded my Asterisk system (from 1.2 to 1.4) and I have started to notice the following messages when I recieve a call on my Zap channel :- [Mar 11 09:20:17] WARNING[4294]: chan_zap.c:8851 zt_pri_error: 1 copying 5 bytes LLC I have a single PRI ISDN 30 link to a Siemens Realitis DX. Here is my zapata.conf :- [channels] echocancel=no echocancelwhenbridged=no rxgain=-5.0

I have spent some time this morning trying to add an Astribank to our current Asterisk, but it failed, so I just removed the hardware, restore the config files to the original setup and started asterisk.; I could see that no Zap channels are started so I did load chan_zap.so: pbx*CLI> module load chan_zap.so [Feb 26 10:32:18] WARNING[3809]: pbx.c:2968 ast_register_application: Already have an

We have a TE110P (single span PRI) and are having tons of echo on all calls, both incoming and outgoing. We didn't have any echo at all yesterday and nothing in any of the configs has changed. All of all calls follow this pattern: Cisco 7960 -> Asterisk -> PRI Here is my zapata.conf [channels] context=all-incomming switchtype=national resetinterval = 3600 priindication =

I have a Toshiba DK424 connected via T1 E&M to a TE110P card. Intermittently when a user dials a number I am getting 'getdtmf' errors on the Ast server and the calls do not go through. If they dial the number once or twice more, it works fine and I receive no DTMF problems. On another note, end users are complaining about intermittent disconnects. T1 is ESF/B8ZS - 24 chan. Other