similar to: No CID on Zaps - TDM400

Hi, I am using asterisk 1.2.5 and have some problems with asterisk connected with an E1 card to our PRI. Dialling in and out generally works. When someone dials in from a mobile phone, all numbers are sent as a block, and the called extension rings as intended. when someone picks up his phone handset, waits for a dial tone, and then dials in manually, the call will be redirected to the

Hello, I have another little problem with my ZAPs channels, in fact, when I received a call, I heard no sound while in the CLI, sound is played: -- Starting simple switch on 'Zap/4-1' -- Executing [s at from-zaptel:1] Answer("Zap/4-1", "") in new stack -- Executing [s at from-zaptel:2] BackGround("Zap/4-1", "hello-world") in new stack --

I am using asterisk version 1.2.6 with Zaptel version 1.2.5. I have a POTs line coming into a Digium TDM01B. It appears to not be getting CID at all. If I hook up a POTS phone to the line CID comes through fine. Inbound and outbound calls work fine but there is just no CID on inbound for this channel.The incoming route for the channel is Zaptel Channel 0. No DID or CID settings applied. My IP

Hello, I'm fairly new to asterisk and Trixbox, I'm setting up a Trixbox based email to fax gateway. At this time, I have a ZAP PRI link between the eFax server and my VoIPSwitch. The ZAP channels are configured, the B and D channels are up, and I have green link lights on either end of my cabling, but when I dial the number I have assigned to my eFax server, the call never seems to route

I've got a system where I'm integrating a Nortel Option 11c with a Trixbox 2.0.0 system using a Sangoma A101 T1 card. (Running on a Dell PowerEdge 350) We've got things mostly up and running and all seems well... except... If I call from a SIP extension (X-lite soft phone) dialing 9xxxx where xxxx is an extension on the Opt 11, the call goes through to the Opt 11 but I have terrible

Can't get a Digium TDM04B working. Asterisk is running. I seem to have setup the trunks OK. But whenever I make an outgoing call get the 'all circuits are busy now' message. If I call in nothing happens at all! Here is my zapata.conf file: ; ; Zapata telephony interface ; ; Configuration file [trunkgroups] [channels] language=en context=from-pstn signalling=fxs_ks fxsks=1-4

Hey all, posted this the other day, but re-read it & realized I didn't give enough info to be useful.. so I thought I'd try again.. I'm using AAH 2.0 (* 1.2.0) and am unable to transfer a call when I initiate the outgoing call. In AMPs general settings, I've tried changing the Dial command using tT but transfers are only available when I'm the recipient of the call, not

I have a TMD400 card installed in a PC with one fxs (installed in slot 2) and two fxos (installed in slots 3 & 4).? fxos work fine but I am unable to get a dial tone for any devices connected to the fxs.? I have correctly connected the power supply to the card and I have even tried moving the card from slot 1 to 2 on the board. Below is from the console when I try to route a call from FXO on

Hi All, It's broken !! (drat) Asterisk if failing to load with the following error (taken from end of /var/log/asterisk/full) after adding bristuff. Can anyone help please? Jul 17 19:57:54 VERBOSE[2503]: == Registered channel type 'Phone' (Standard Linux Telephony API Driver) Jul 17 19:57:54 VERBOSE[2503]: [chan_zap.so]Jul 17 19:57:54 VERBOSE[2503]: [chan_zap.so] =>

I don't know if is a common problem but what I've found: First my config: Zaptel.conf: defaultzone=uk fxoks=1-2 fxsks=3-4 loadzone = uk Zapata.conf [channels] language=en context=from-pstn usedistinctiveringdetection=no usecallerid=yes cidsignalling=v23 cidstart=polarity hidecallerid=no callwaiting=yes usecallingpres=no callwaitingcallerid=yes

I've been going nuts lately trying to get rid of an annoying echo problem that makes my asterisk server unusable when clients try to call me. Here's the breakdown of the issue - Hoping that someone can throw me a clue: My setup is as such: Single AMD Athon machine with X100P clone card and voip through multiple providers . * Inbound calls through the X100P that do not bridge to

hi you, I'm having problem with voice quality on my trixbox using TDM2400B.The trixbox is connected via 20 FXO ports on a TDM2400 with the hardware echo cancel module. Echo cancel almost works, but the users hear what they describe as a 'background crackle/buzz' coming back when they talk. anyone have the same problem? pls help me. thanks a lot. my trixbox and config

Hello I setup Asterisk@Home with purely VoIP and it worked fine. I then added an X100P card so I could call out / take inbound calls via PSTN and that went fine. But I have just added a TDM400P card (specifically a TDM30B) and now problems. Here is some of the output. Any ideas on what I should be looking at next? When I run genzaptelconf -s -d I get lots of erors on screen - bit I can

Hey All, I have an Asterisk box connected to a Nortel Option 11C via a T1. In the Asterisk box we have a Sangoma A101C and in the Nortel we have a TMDI card. The Nortel is also hooked to the PSTN via a T1 on a different NTAK09 PRI card. I've included the Zapata.conf and zaptel.conf files below. Our issue is that when a call is sent over the tie line between the two systems, the audio on the

Any ideas? 51] logger.c: [chan_zap.so] => (Zapata Telephony) Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing '/etc/asterisk/zapata.conf': Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing '/etc/asterisk/zapata.conf': Found Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing '/etc/asterisk/zapata-auto.conf': Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing

Hi ALL Have installed asterisk@home 1.0 On FWD DID's, appears that 2 calls are generated to the inbound extention. I have confirmed this on a number of friends boxes also. Does anyone have a fix for this ? I set the DID simply to a custom context and it did the same... Anyone have a way to fix this ? Here is the output...... -- Accepting AUTHENTICATED call from 65.39.205.121, requested

Hi, guys, For my server, if i use my handphone to call in the PSTN line by TDM400p card, the server could not receive the caller id correctly. anyone knows the problem? I am currently using asterisk 1.2.14 with freepbx 2.2.1. The CLI is as below, "Caller ID name is 'zap1' number is '4521'" , this 4521 is one of my FXS zap extension created. dialparties.agi: Starting New

Skipped content of type multipart/alternative-------------- next part -------------- asterisk1*CLI> soft hangup Zap/1-1 Requested Hangup on channel 'Zap/1-1' == Spawn extension (macro-exten-vm, s-BUSY, 2) exited non-zero on 'Zap/1-1' in macro 'exten-vm' == Spawn extension (ext-local, 220, 1) exited non-zero on 'Zap/1-1' -- Hungup 'Zap/1-1' --

OK, i've got asterisk @ home 1.3 up and running with Broadvoice. BUT I have one nagging problem to sort out. When you call my BV # the calling party gets no ring indication, just silence until either I answer the phone, or the call bounces over to voicemail. below is the console output when a call is recieved. what am i missing here? thanks Bernie -- Executing

Running Asterisk Head 1.0.9. Below is a trace of a call delivered to my system which had no caller ID. For some reason, dialparties.agi shoves the incoming provider's IP address into the caller ID so you never have a call that is screened for PrivacyDirector. Is anyone else seeing this issue as well? Have I missed a patch? This call shows on the display with a name of "Unknown"